See what our Experts say about this Yakima Roof Rack

• Will a Yakima Roof Rack System Fit My 2020 Toyota Highlander LE?
  I confirmed with Yakima that mounting points that are on your bare roof of your 2020 Toyota Highlander will fit a roof rack system. After you pop off the tab that covers the mounting points, there is a screw that you will use to attach a roof rack system. I went ahead and attached a video that shows how you would attach a Yakima roof rack system on the 2020 Toyota Highlander. For the parts you need for that setup, you will need the following parts: - Yakima JetStream Crossbars - Aluminum...
  view full answer...
• Recommended Roof Rack For A 2023 Toyota RAV4 With A Thule Hullavator
  Hi Cathy, To ensure that you can get the extra extension to mount the Thule Hullavator # TH898 you'll want to go with a Yakima roof rack system. Yakima crossbars run their mounting track the entire length of the crossbar so you can go with ones that are longer than your typical length without worrying if the mounting feet will be able to connect. You'll want the following components: Yakima JetStream Crossbars - Black - 60" Long # Y00426 or silver # Y00429 SkyLine Towers for Yakima Crossbars...
  view full answer...
• Square Bar Roof Rack that Fits 2020 Ram 1500 Quad Cab
  Thule offers a square bar roof rack that fits your 2020 Ram 1500 quad cab with the part # TH712500, # TH710501, and # TH145199. Then for a square bar roof rack the Thule Portage part # TH819 would work great.
  view full answer...
• Recommended Roof Rack for a 2022 Honda Insight
  Hey Andy! The 50" crossbars on the Yakima BaseLine Roof Rack Kit item # Y88UB can be swapped out but the next largest size is the 60" Long item # Y00429 so I do not think that's going to be a viable option. By law the crossbars are not supposed to stick out past the rear view mirrors. If you want to pursue this option you'll need the following parts: BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item...
  view full answer...
• Can I Put A 60" Long Crossbar On A 2022 Subaru Outback
  Hello Joe, thanks for reaching out. Yes, it is possible to put a 60" (or longer) crossbar on your 2022 Subaru Outback. I will need to verify a bit more vehicle information before I can recommend the correct parts. Does your outback happen to be the Wilderness edition? Let me know. Also please verify that your Outback has the factory installed raised rails running from front to back. Let me know and I will be able to narrow down the right roof rack. For example, if you do have the Wilderness...
  view full answer...
• Which Yakima Roof Rack Fits 2022 Ford Maverick
  Hi Alvin, Nice choice going with the Yakima rack as they make really high-quality gear. As for the correct parts for your 2022 Ford Maverick, you can actually get everything combined with just one part number depending on the bars you want. You mentioned the FX, and that is a flush-style roof rack system, which means the bars only go the width of your roof with no overhang. The FX uses bars and towers that are combined, so they aren't actually separate; to go that route you'd just need...
  view full answer...
• Recommended Roof Rack for a 2023 GMC Yukon XL
  To add a roof rack to your 2023 GMC Yukon XL, you will want the roof rack by Yakima which includes the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 Black or item # Y00429 in Silver SightLine Towers for Yakima Crossbars - Flush Side Rails - Qty 4 item # Y64AR SightClip Fit Kit for Yakima SightLine and RidgeLine Roof Rack Towers item # Y44UV I have attached a couple of pictures below that will show you what this roof rack looks like and how to...
  view full answer...
  
• Best Roof Rack For 2024 Kia EV9 With Raised Side Rails
  The best roof rack for your 2024 Kia EV9 with raised side rails is from Yakima, and consists of the following part numbers: - Yakima JetStream Crossbars - Silver # Y00429 or Black # Y00426 - TimberLine Towers for Yakima Crossbars # Y33TR I really like the Yakima brand due to how quiet the bars are; they have what are called "WindRidges" on top that control the flow of the air both over and under the bar, which minimizes both vibration of the bar and wind noise. It is also highly durable,...
  view full answer...
• Parts Needed To Install 60" JetStream Bars On A 2021 Toyota Tacoma Double Cab With Factory Rails
  We can definitely help set you up. To install a pair of 60" Yakima JetStream bars on your 2021 Toyota Tacoma Double Cab with factory rails, all you will need is a set of TimberLine Towers # Y33TR, and your crossbars. We have the 60" JetStream bars available in silver # Y00429 or in black # Y00426.
  view full answer...
• Will Rhino-Rack Crossbars Fit On Yakima BaseLine Towers?
  The top channel on most crossbars like the Rhino-Rack and Yakima are similar but you should never mix and match towers and crossbars between different manufacturers. Their components are designed to work specifically with each other and your Yakima towers may not work properly with the Rhino-Rack crossbars. Instead you will want to stay with the Yakima crossbars from the list below to ensure they fit together properly and you have a manufacturer who will stand behind the warranty for the...
  view full answer...
• How to Determine Correct Roof Rack For 2024 Kia Telluride
  I'm going to go ahead and respectfully disagree that we're idiots, Paul. I'm confident we can figure out the combination for a roof rack on your 2024 Kia Telluride, and there are three possible options Kia has for your roof - flush-mounted rails, raised side rails, and a bare roof. I made some diagrams below showing test fits on a Kia Telluride with photos from the nice folks at Yakima so you can see the difference (please note these are just test fit photos, and not exactly how the rack...
  view full answer...
  
• Yakima Crossbar Length For 2022 Lexus GX 460 & Hullavator
  I checked with Yakima regarding the crossbar length, and they do say 50, which is odd for your 49 inch rails. With that distance between your rails, don't use the 50 inch bars, use the 60 inch long JetStream bars, either Silver # Y00429 or Black # Y00426. The rest of the parts for the Yakima rack on your 2022 Lexus GX 460 remain the same; Towers # Y53TR, Landing Pad 30 # Y25ZR and Lock Cores # Y07204.
  view full answer...
• Recommended Roof Rack for a 2024 Acura MDX w/ No Roof Rails
  Yes, we do! To add a roof rack to your 2024 Acura MDX with a naked roof you will need the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 for Black or item # Y00429 for Silver BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06163 BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06178 This aero bar roof rack system has a 165 lbs capacity....
  view full answer...
• Recommended Roof Rack for a 2024 Nissan Pathfinder w/ Raised Rails
  I would be happy to! To add a Yakima roof rack to your 2024 Nissan Pathfinder you will need the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 for Black or item # Y00429 for Silver TimberLine Towers for Yakima Crossbars - Raised, Factory Side Rails - Qty 4 item # Y33TR This aero bar roof rack system has a 165 lbs capacity. I recommend adding the Yakima Same Key System item # Y07204 to prevent theft. A great perk of Yakima's products is you can...
  view full answer...
• Parts Needed to Use Yakima JetStream Bars with a 2024 GMC Yukon XL W/ Flush Rails
  Niels, to continue using your Yakima JetStream Crossbars # Y00429 with your 2024 GMC Yukon XL with flush rails, you'll just need the SightClip Fit Kit for Yakima SightLine and RidgeLine Roof Rack Towers # Y44UV and the SightLine Towers for Yakima Crossbars # Y64AR.
  view full answer...
• Recommended Roof Rack System For 2021 Kia Telluride LX with Naked Roof
  The only company at the moment (June 2023) that makes a roof rack system for your 2021 Kia Telluride LX with a naked roof is Yakima, so for a roof rack system you'll need the following components: Crossbars # Y00429 Feet # Y28TR Fit Kits # Y06125 and # Y06165 I'd also recommend adding the locks # Y07204 to secure the roof rack to your roof to deter theft. Out of all of the crossbar options for your vehicle this is by far the best due to the Aero design to cut down on wind noise the most,...
  view full answer...
• Does Thule Force XT XL Rooftop Cargo Box Fit Yakima Roof Rack on 2023 Acura MDX
  Yes, the Thule Force XT XL # TH6358B will fit very easily on the Yakima roof rack for your 2023 Acura MDX. There won't be any issues with the fit of your cargo box on this rack it will fit perfectly so you can continue to use it. The only thing you need to do is pick the right Yakima rack for your '23 MDX, depending on if it has a bare roof or flush-mounted rails. Bare Roof - Yakima JetStream Crossbars - Silver # Y00429 or Black # Y00426 - BaseLine Towers # Y28TR - BaseClip Fit Kit # Y06163...
  view full answer...
• Recommended Roof Rack for a 2024 Acura RDX w/ a Naked Roof
  Congrats on the new SUV! Yes, we do have a way to attach a roof rack to your 2024 Acura RDX even though you do not have roof rails. It is the roof rack by Yakima and it includes the following parts: Yakima JetStream Crossbars - Aluminum - 60" Long - Qty 2 item # Y00426 for Black or item # Y00429 for Silver BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 item # Y06174 BaseClip Fit Kit for Yakima BaseLine...
  view full answer...
• Yakima Roof Rack that Fits 2019 Honda Passport with Raised Rails
  Since your 2019 Honda Passport has raised rails the roof rack feet that fit it are the ones that wrap around the bars whereas the flush bar roof styles are the ones that have options that attach directly to it. So for a Yakima there is the Jetstream part number # Y00429 and # Y33TR which is an aero shaped bar setup that wraps around your raised rails. This is a very solid setup that will work great and is no less reliable than any other option.
  view full answer...
• Roof Rack For A 2017 VW Golf Sportwagen To Use With The Thule Hullavator
  We can definitely set you up with a roof rack for your 2017 Volkswagen Golf Sportwagen that is compatible with the Thule Hullavator # TH898. The Hullavator requires the crossbar to overhang past the tower by 4" to 8", so it will be best to use a solid aero bar setup with a slightly longer crossbar. For that I recommend the Yakima Jetstream roof rack. This will consist of the following parts: Yakima TimberLine Towers for Yakima Crossbars # Y33TR Yakima JetStream Crossbars - Aluminum - Silver...
  view full answer...
• What Roof Rack Do You Recommend for a 2007 Honda Element SC?
  Absolutely! For a great roof rack system that will fit your SC version of the 2007 Honda Element, I recommend the following parts: - Yakima JetStream Crossbars - Aluminum - Silver - 60" Long - Qty 2 # Y00429 - SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4 # Y53TR - Landing Pad 9 for Yakima SkyLine and Control Towers - Qty 4 # Y00229 - (Optional for extra security) Yakima Same Key System (SKS) Lock Cores (QTY 2) # Y07202 With the above...
  view full answer...
• Roof Rack Recommendation for 2021 Toyota Highlander with Naked Roof
  Hey Ronnie, I attached a link to this page that shows all of the roof racks that are a fit for your 2021 Toyota Highlander with a naked roof but my favorite option is the Yakima Jetstream part # Y00429, # Y28TR, # Y06153, # Y06132 as we had chance to install all of the racks we carry and we all agreed the Yakima racks are the nicest and the easiest to use. This is a through bar design which means the bars are longer than the feet of the rack which is great for if you need max bar space. If...
  view full answer...
• Roof Rack for Thule Canyon XT Roof Cargo Basket on 2020 Subaru Ascent
  Your 2020 Subaru Ascent will require a roof rack to carry any cargo basket, including the Thule Canyon XT Roof Cargo Basket # TH859XT. Assuming you have raised side rails that run front to back on your Ascent, here is the roof rack that will work with your Subaru: - Yakima JetStream Crossbars # Y00429 (Silver) or # Y00426 (Black) - TimberLine Towers for Yakima Crossbars # Y33TR As for the paddleboards, there isn't anything designed to carry them in a cargo basket so you can use whatever...
  view full answer...
• Rooftop Cargo Carrier Recommendation for 2020 Toyota Highlander with Panoramic Roof
  For a great option for your 2020 Toyota Highlander with panoramic bare roof, I recommend the Thule Force XT XXL # TH6359B. This box has the largest internal dimensions out of all of our cargo boxes. It also comes with a dual-opening lid that can be accessed from either side of your vehicle. I confirmed that your trunk can fully open with this box mounted on your roof. If you already have crossbars, I recommend measuring your bars to make sure they do not exceed 3-1/2" wide x 1-11/16"...
  view full answer...
• Can Thule Hullavator Install on Yakima Crossbars
  The Thule Hullavator Pro # TH898 can fit round bars by grabbing around the crossbar and can fit aero shaped bars if the bars have a channel on top of them. Which the Yakima aero shaped bars don't have top channels so to go the Yakima route will require round bars which includes the part numbers # Y00408, # Y53TR, # Y03536, and # Y00241 and you'd be set.
  view full answer...
• Recommended Roof Rack For Attaching A Thule Hullavator To A 2021 Toyota Highlander
  To attach the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs # TH898 to your 2021 Toyota Highlander you'll need a roof rack that has a T-Slot in the crossbars for the Hullavator to slide into. Currently the only brand of roof racks we carry for your vehicle that are compatible with your flush mounted rails is Yakima. I recommend the following parts to complete your roof rack: Yakima HD Crossbars - 55" Long # Y01156 SkyLine Towers # Y53TR Landing Pad 28 # Y66VR HD...
  view full answer...
  
• What is the Difference Between Yakima HD Tracks and Regular Yakima Tracks?
  The difference between the Yakima HD Crossbars like the # Y74MR and the regular Yakima Tracks like the # Y01135 is that they are compatible with different feet and adapters. With the HD tracks, they will fit the Yakima Skyline towers, OverHaul HD system, or OutPost HD systems. In order to use these components, you need to use the Landing Pad 26 for Yakima SkyLine Towers - Qty 2 # Y75ZR or the Yakima HD Track Adapter Kit for Yakima OverHaul HD and OutPost HD Truck Racks - Qty 4 # Y75RR....
  view full answer...
• Recommended Roof Rack for Mounting a Thule Hullavator Pro on a 2021 Toyota RAV4
  The Thule Hullavator Pro, part # TH898, does in fact need crossbars that extend 4" - 8" beyond the feet. To use the flush rails on your 2021 Toyota RAV4, you will need a roof rack that has feet that are compatible with the rails. With those two stipulations in mind, the Thule WingBar Evos don't look like they will provide enough clearance with their 47" of crossbar length. Instead, I recommend the Yakima HD Crossbars, part # Y01156. They are 55" long, so they will have the extension you...
  view full answer...
• What Roof Basket will Attach Directly to My Raised Rails on My 2022 Toyota 4Runner?
  I have a great option for you if you do not like the height of the Yakima LockNLoad # Y05045 with the Timberline Towers # Y33TR on your raised factory side rails on your 2022 Toyota 4Runner. Unfortunately, I confirmed with Yakima that you will need to have the Timberline Towers in order to attach the LockNLoad to your rails. They cannot be mounted without those towers directly to your rails. In order to complete this setup, you also need 2 sets of the LockNLoad SL Adapter for Yakima SkyLine...
  view full answer...
• Can 60 Thule AeroBlade Bars be Used on a 2015 Jeep Grand Cherokee with the E Group Package
  To determine if you can use the 60" WingBar Evo Crossbars, part # TH711500 or part # TH711520, will fit on your 2015 Jeep Grand Cherokee you first need to measure the center to center distance between the mounting holes where the Podium feet will sit. I have attached a picture showing where you want to measure. If this measurement falls between 46-1/2" - 59-3/4" then the 60" bars will fit. For your E Group package you also need the Podium Foot Pack # TH460R and the Fit Kit # THKIT3142 to...
  view full answer...
  
• Recommended Roof Rack For Installing A Yakima ShowDown Kayak Carrier On A 2021 Toyota Highlander
  For your 2021 Toyota Highlander with flush mounted rails I recommend the Roof Rack by Yakima which includes: Yakima HD Crossbars - Aluminum - Black - 55" Long - Qty 2 # Y01156 SkyLine Towers for Yakima Crossbars # Y53TR Landing Pad 28 for Yakima SkyLine And Control Towers - Qty 4 # Y66VR HD Bar SL Adapter # Y03541 The Yakima ShowDown Kayak or SUP Carrier and Lift Assist w/ Tie-Downs # Y04081 will clamp onto the crossbars of this roof rack system for an easy peasy installation. You will...
  view full answer...
• Recommended Roof Rack for Hullavator and Kayak Carrier on 2019 Honda Pilot
  Thank you for all of the information! While you are able to use the Hullavator # TH898 with your setup as far as weight goes, this kayak carrier does require the crossbars to stick out 4" - 8" out past the roof rack feet. Since the Thule SquareBars have a limited amount of space under them for the feet you can only use the 53" Bars # TH712400 but this wouldn't give you the required spacing for the Hullavator. I recommend using the Yakima 60" JetStream Crossbar # Y00426 instead with the...
  view full answer...
• Roof Rack Option For A 2016 Lexus GX460 With Factory Flush Rails
  Good morning, Doug. I do have a potential solution for you, but I am sorry to say that Thule does not make a fit kit for the 2016 Lexus GX460. So, there is unfortunately no way to mount your Thule Evo bars on this vehicle. Our best option would be to get a whole new roof rack. Yakima does make a fit kit for the 2016 GX460 flush rails, so one of their JetStream racks would be a great option that is comparable to Thule. The complete Yakima roof rack consists of the following parts: - Yakima...
  view full answer...
• Recommended Yakima Roof Rack Upgrade for Subaru Factory Roof Rack
  The factory roof rack on the 2016 Subaru Outback Wagon has minimal options to fit the factory roof rack which is different than the factory side rails or flush mounted rails. You can use the Landing Pad 15 for Yakima Control Towers - Qty 4 # Y00241 which will allow you to simply remove your factory crossbars and mount these pads in their place. Then you can use the SkyLine Towers for Yakima Crossbars # Y53TR and round bar adapter # Y03536 if you want to use round bars like the 48 inch...
  view full answer...
  
• Yakima Roof Rack for 2023 Subaru Outback With Thule Hullavators
  Hi Tina; I also prefer Yakima so I'm glad we're on the same page. For your 2023 Outback and Hullavators I recommend the JetStream roof rack. You will need the following: -Yakima JetStream Crossbars # Y00426 -SkyLine Towers for Yakima Crossbars # Y53TR -Landing Pad 27 for Yakima SkyLine And Control Towers # Y46VR The JetStream crossbars are extremely quiet so you won't have a bunch of road noise added to your day to day driving. If you want to keep your rack secure you can also add the...
  view full answer...
• How to Carry the Yakima MajorShady 270 Awning on a 2024 Subaru Outback Wagon
  The Yakima MajorShady 270 Awning # Y82AV installs via the T-Slots in a roof rack so we'll need to get you an aftermarket roof rack since your 2024 Subaru Outback Wagon OEM crossbars don't have that T-Slot system. For something that's cost-effective and gets the job done I recommend the Malone AirFlow2, but if you're wanting something with higher quality and will be a better setup for longevity then I recommend the Yakima JetStream system. Here are the parts you'll need for each: Malone...
  view full answer...
• Installation of Yakima Roof Rack on 2019 Jeep Grand Cherokee With Flush Mount Rails
  Assuming your 2019 Jeep Grand Cherokee has the black and chrome flush-mounted rails that run front to back, you are correct that the roof racks you mentioned do install into the same place the factory bolts are. I have added links to an installation video of the Yakima JetStream roof rack on a Jeep Grand Cherokee with flush mount rails so you can see exactly how the rack installs. The Yakima JetStream (which is shown in the accompanying photo installed on a Jeep Grand Cherokee) consists...
  view full answer...
  
• How to Carry SUP and SkyBox 21 on Roof of 2006 Land Rover LR3
  Could you let me know if your Land Rover LR3 has factory installed tracks that run from the front to back or if the OEM roof rack is more of a raised type? I tried doing some research but was having trouble finding anything that looked like it was an actually OEM roof rack. If you could send me some pictures of your roof rack system that would help me know what you have.
  view full answer...
  
• Roof Rack With Black Crossbars for Pace Edwards BedLocker Rails on 2019 Ford F-350
  Hi Michael; you can use the same fit kit # THKIT3101 and mounting feet # TH460R. However, the longest WingBar Evo is 60" # TH711520 which probably won't be long enough for your truck bed. That is why Conner originally chose the # TH713700 which are 79" long. For bars that are black I recommend switching to a Yakima setup. You will need the following: -Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 -SkyLine Towers for Yakima Crossbars # Y53TR -Yakima CoreBar Crossbars -...
  view full answer...
• 2021 Jeep Grand Cherokee L Yakima Roof Rack for Flush Rails
  I'd be more than happy to help out! The parts you need to get the Yakima JetStream roof rack installed on your 2021 Jeep Grand Cherokee L flush rails include the following: 50" JetStream Crossbars - # Y00425 SkyLine Towers - # Y53TR Landing Pad 19 - # Y00245 Lock Core Kit - # Y07204 (optional) This gives you the exact parts that were used in the linked video. If you let me know what you are planning on using this roof rack for I'd be more than happy to make a recommendation for you!
  view full answer...
• Roof Rack for 2019 Subaru Outback with Rails to Carry Hullavator and Hull-a-Port
  The 47 inch bar would definitely not work for two Hullavators; thanks for calling that to our attention and that information has been edited. You would need crossbars that are a minimum of 76 inches for a pair of Hullavators.
  view full answer...
• Will Thule Hullavator Fit a Yakima Roof Rack on a 2018 Subaru Outback
  The Thule Hullavator, # TH898, will fit on a Yakima roof rack so if you like the spacing and looks of the Yakima racks you can certainly go that route for your 2018 Subaru Outback. With the Hullavator the roof rack crossbars need to stick out past the mounting feet by at least 4 inches. What this means you will need to use longer bars than what would normally be recommended for the vehicle. If you go with a round bar system then you will need the following parts: Crossbars # Y00409 SkyLine...
  view full answer...
• Parts Needed For A Yakima Roof Rack On A 2021 Ram ProMaster City With Factory Mounting Points
  Hi Phillip, To connect to the factory mounting points on the roof of your 2021 Ram ProMaster City you'll need Landing Pad 22 # Y00248 along with SkyLine Towers for Yakima Crossbars # Y53TR. From there you can go with crossbars like the Jetstream # Y00425 (50") or # Y00426 (60"). I've attached a picture below from Yakima's website showing this fit.
  view full answer...
• Recommended Roof Rack For A 2023 Toyota RAV4 With A Thule Hullavator
  Hi Cathy, To ensure that you can get the extra extension to mount the Thule Hullavator # TH898 you'll want to go with a Yakima roof rack system. Yakima crossbars run their mounting track the entire length of the crossbar so you can go with ones that are longer than your typical length without worrying if the mounting feet will be able to connect. You'll want the following components: Yakima JetStream Crossbars - Black - 60" Long # Y00426 or silver # Y00429 SkyLine Towers for Yakima Crossbars...
  view full answer...
• Best Roof Rack for 2020 Kia Soul with Fixed Mounting Points
  The best roof rack for your 2020 Kia Soul with a naked roof (fixed mounting points) is from Yakima because it will give your Kia a roof rack that combines effectiveness and style while minimizing any wind noise that can occur with lesser roof racks. This roof rack is made up of: - Yakima JetStream Crossbars # Y00425 - SkyLine Towers for Yakima Crossbars # Y53TR - Landing Pad 22 # Y00248 - Same Key System Lock Cores (Optional) # Y07204 This roof rack will look stellar atop your 2020 Kia...
  view full answer...
• Roof Rack for Carrying a Canoe/Kayak on a 2014 Subaru Impreza with a Naked Roof
  While we do have roof racks for your 2014 Subaru Impreza, the (discontinued) Custom Fit Kit WB-K473 you referenced is for various years and models of GM pickups and there isn't a Whispbar roof rack currently in production that fits your vehicle. If you like the higher quality of a Whispbar product then you'll want to go with a Yakima roof rack as they actually manufacture the Whispbar brand. From what you were looking at I'm guessing you have a Sedan that isn't the WRX. For this you'll...
  view full answer...
• Will Malone SteelTop Roof Rack Fit 2025 Subaru Outback
  Hi John; is your 2025 Outback the Wilderness model? The Malone SteelTop Roof Rack # MPG203 only fits the rails on the Wilderness. This will not fit the factory rails on the regular Outback models. If that is what you have, let me know in the comments below and I can see what else is available. Are you looking for a specific crossbar length?
  view full answer...
• Yakima Roof Rack Parts for 2018 Subaru WRX
  Yes, the Yakima roof rack you mentioned that consists of part numbers # Y00425, # Y53TR, and # Y00233 is a confirmed fit for the roof of your 2018 Subaru WRX and would be a great option. This would then be compatible with the Yakima Forklift part # Y02098 that you mentioned.
  view full answer...
• What is the Difference Between Yakima Landing Pads 1 and 4
  The difference between Landing Pad 1 # Y00221 and Landing Pad 4 # Y00224 is the hardware. For LP1 the 'A' plate dimension is 7/8" x 11/16" and for LP4 the 'C' plate dimension is 1 3/16" x 13/16" so they fit different vehicles.
  view full answer...
• How to Carry SUP and SkyBox 21 on Roof of 2006 Land Rover LR3
  Could you let me know if your Land Rover LR3 has factory installed tracks that run from the front to back or if the OEM roof rack is more of a raised type? I tried doing some research but was having trouble finding anything that looked like it was an actually OEM roof rack. If you could send me some pictures of your roof rack system that would help me know what you have.
  view full answer...
  
• Parts Needed to Use a Yakima OverHaul HD Ladder Rack and Roof Rack with a Pace Edwards Ultra Groove
  I believe that I know what you are wanting to do. You are wanting the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover # Y01151-5855 which fits your Sierra and is compatible with your Pace Edwards Ultra Groove tonneau cover. This provides you with a ladder rack that uses Yakima HD bars. Then you also want to use the HD bars on roof rack towers to provide a lower rack using the t-slots in your Ultra Groove Rails. In that case, the Landing Pad 4 for Yakima SkyLine and...
  view full answer...
• Will Yakima Landing Pad 1 and 4 Fit Rhino-Rack RTC-Style Roof Rack Tracks
  Yes, I test fit the Rhino-Rack RTC-Style Roof Rack Tracks # RTC12JW with the Landing Pad 1 # Y00221 and the Landing Pad 4 # Y00224 and found that they are compatible with each other. All of these parts come in a quantity of 2. To complete your setup you also need 4 of the Yakima Control Tower # Y8890027 and a set of round bars that match your application. We have a variety of round bar lengths for you to choose from. These include the following: 48" Round Bars - # Y00408 58" Round Bars...
  view full answer...
• Recommended Yakima Roof Rack for 2007 Land Rover LR3 with Factory Track System
  The Thule Fit Kit # THKIT3112 is the confirmed fit for your 2007 Land Rover LR3. Since they do not fit in the way you desire, I recommend the Yakima Landing Pad 4 for Yakima Control Towers - Qty 2 # Y00224 ( you will need 2 kits), the Skyline towers # Y53TR and the Jetstream Crossbars # Y00425. I also recommend the locks to secure your roof rack # Y07204. This system will mount differently into your factory rails for a confirmed fit.
  view full answer...
• Recommended Crossbars and Roof Basket for a 2008 Hummer H3 With Factory Rails
  For your 2008 Hummer H3, I recommend checking out the Yakima MegaWarrior Extra Large Roof Rack Cargo Basket # Y07080-82. This cargo basket will easily attach to a set of crossbars like the Yakima HD Crossbars # Y01156, measures 74" long x 48" wide x 6-1/2" tall, and has a maximum weight capacity of 130-lbs. To finish the crossbar setup, you'll also need the SkyLine Towers for Yakima Crossbars # Y53TR, HD Bar SL Adapter for Yakima BaseLine, SkyLine, TimberLine, and RidgeLine Towers #...
  view full answer...
• Landing Pads For Rails Of A Carry On Utility Trailer For Yakima Control Towers
  If the rails you are referring to on your utility trailer are the track style, then your Yakima Control Towers will fit with Landing Pad 4 for Yakima Control Towers - Qty 2 # Y00224. If you will me drilling into metal support rails then you will want the Landing Pad 7 for Yakima Control Towers for Metal Roofs - Qty 2 # Y00227. You may also be interested in the Round 78" CrossBars for Yakima Roof Rack System (QTY 2) # Y00411 or the Round 86" CrossBars for Yakima Roof-Rack System (QTY 2)...
  view full answer...
• Roof Rack Recommendation for a 2008 Hummer H3 with Factory Tracks
  For a roof rack that is confirmed to fit the tracks on your 2008 Hummer H3 you would want the Yakima part numbers # Y00408, # Y53TR, # Y03536, and # Y00224. You can also lock this rack with the lock core set part # Y07204 which would help prevent theft. Sorry to hear about your factory rack getting stolen.
  view full answer...
• Replacement Yakima Landing Pad For Roof Rack Tower
  The landing pad you have is either going to be in the kit Landing Pad 1 # Y00221 or Landing Pad 4 # Y00224. The landing pad 1 has a more square shaped channel nut while the landing pad 4 has a more rectangular channel nut.
  view full answer...
• Roof Rack for 2007 Hummer H3 with Roof Rack Channels
  For your 2007 Hummer H3 with the roof tracks like you pointed out we have the Yakima Skyline roof rack part numbers # Y00425, # Y53TR, and # Y00224 as a confirmed fit. This attaches to the slots you have and gives you a high quality rack that due to it's bar shape will be very aerodynamic.
  view full answer...
• Parts Needed to Carry Spare Wheel on Roof of 2008 Hummer H3
  If you installed a Yakima roof cargo basket like the # Y07070 you could use the Spare Tire Carrier part # Y07076 to carry the spare on your roof. You would need a roof rack installed on your 2008 Hummer H3 as well like the Yakima round bar roof rack part # Y00408, # Y53TR, # Y03536, and # Y00224. We don't have a good solution to cover where the old spare was installed. If you make it near St. Louis MO we could help out with the install too!
  view full answer...
• Roof Rack Recommendation for 2005 Chrysler Town and Country Van
  Your 2005 Chrysler Town and Country van could be equipped with three possible roof configurations (factory tracks, raised side rails or nothing at all). From your description is sounds like you have the factory tracks. For this roof style we have rack options that can be seen on the link provided. A cost-effective basic round bar system is offered from Yakima and consists of parts # Y00408, # Y00224, # Y53TR and # Y03536. Round bars offer excellent compatibility with accessories like bike...
  view full answer...
• Roof Rack Recommendation for 2009 Hummer H2
  For a 2009 Hummer H2 we have the Yakima Roof Rack part numbers # Y00409, # Y53TR, # Y03536, and # Y00224 which is a confirmed fit and will work well. We don't have anything for a 2011 model as there wasn't a 2011 model made in the US nor do we have anything that was made by Hummer.
  view full answer...
• How to Install Rhino-Rack Pioneer Platform Rack on a 2003 Hummer H2
  To install a platform rack on your 2003 Hummer H2 we first need a roof rack and for that I recommend the Yakima JetStream system that includes the following parts: - 60" JetStream Crossbars # Y00426 - SkyLine Towers # Y53TR - Landing Pad 4 # Y00224 This installs directly to the fixed mounting points on your Hummer which then allows you to use the Rhino-Rack Pioneer Platform Tray # RR82TB along with 2 of the Mounting Kit # RR43105 to get it installed. The Pioneer Platform # RR85ZW...
  view full answer...
• Roof Rack Fits for 2003 Chevrolet Suburban
  The current Yakima round bar roof rack that fits your 2002 Dodge Grand Caravan consists of parts # Y00408, # Y53TR, # Y03536 and # Y00224. All roof rack fits for the 2003 Suburban are shown on the linked page but no Yakima branded racks are among them. You can select your roof type using the drop-down menu tool at the top of the page to see roof racks that will work on your 2003 Suburban. If you have factory roof tracks then a cost-effective square bar rack confirmed to fit is the Inno...
  view full answer...
• Roof Rack Spacing On Roof Of 2006 Dodge Caravan With Sliding Doors
  When installing the Yakima roof rack on your 2006 Dodge Caravan with the sliding doors, the location of the feet and bars is not something that can be adjusted for each load. They are designed for a specific location so you would need to use other accessories like a roof basket for your specific load to give further support. To order the roof rack custom made for your Caravan, you will need part # Y00425, # Y53TR, and part # Y00224. I have attached a product review video for this roof...
  view full answer...
• Parts Needed to Carry the Thule Roof Mounted Cargo Basket # TH859XT on a 2005 Dodge Caravan
  To carry the Thule Canyon XT Roof Mounted Cargo Basket # TH859XT on your 2005 Dodge Caravan you will just need a roof rack (if you don't already have one). The Thule basket is compatible with round, square, aero, elliptical, and most factory crossbars. Should you have the factory installed tracks that front to back I recommend the Yakima roof rack which consists of their JetStream Crossbars # Y00425, the SkyLine Towers # Y53TR, and the Landing Pad 4 # Y00224. For a 2005 Caravan that has...
  view full answer...
• Recommended Bike Carrier for Hummer H3
  The Swagman Pick-Up Truck-Bed-Mounted Bike Carrier is designed for pick up truck beds, so it is not a fit for your Hummer H3. However, I do have several bike carrier options for your Hummer. Our most popular bike rack for the Hummer H3 is the Swagman Original # S64400 4 Bike Rack for 2" Hitches. I have linked to a video review of the bike rack for you to check out. I have also linked you to a FAQ article that shows how to measure the distance between your hitch pin hole and the furthest...
  view full answer...
• Recommended Roof Rack and Mud Flaps for 2007 Hummer H3
  For your 2007 Hummer H3, I recommend the Yakima JetStream Roof Rack, which consists of parts # Y00425, # Y00148 and # Y00224. This rack features two 50 inch, aerodynamic crossbars with a weight capacity of 165 pounds. They have a lightweight, durable and rustproof aluminum construction that will be perfect for your particular driving conditions. The asymmetrical shape will provide an extremely low profile and quiet system when installed on your Hummer. The SkyLine Towers will attach to...
  view full answer...
• Recommended Roof Rack for a 2012 Land Rover Range Rover Sport
  The roof rack I recommend for a 2012 Land Rover Range Rover Sport will be dependent on roof configuration. If you have a bare roof then I recommend the Thule WingBar Evo Crossbar System part # TH711520, part # TH710501, and part # TH145116. If you have factory installed tracks then I recommend the Yakima Jetsream Crossbar System part # Y00426, part # Y53TR, and part # Y00224. These are both excellent top-of-the-line options.
  view full answer...
• What is the Difference Between Yakima Landing Pads 1 and 4
  The difference between Landing Pad 1 # Y00221 and Landing Pad 4 # Y00224 is the hardware. For LP1 the 'A' plate dimension is 7/8" x 11/16" and for LP4 the 'C' plate dimension is 1 3/16" x 13/16" so they fit different vehicles.
  view full answer...
• How to Carry SUP and SkyBox 21 on Roof of 2006 Land Rover LR3
  Could you let me know if your Land Rover LR3 has factory installed tracks that run from the front to back or if the OEM roof rack is more of a raised type? I tried doing some research but was having trouble finding anything that looked like it was an actually OEM roof rack. If you could send me some pictures of your roof rack system that would help me know what you have.
  view full answer...
  
• Parts Needed to Use a Yakima OverHaul HD Ladder Rack and Roof Rack with a Pace Edwards Ultra Groove
  I believe that I know what you are wanting to do. You are wanting the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover # Y01151-5855 which fits your Sierra and is compatible with your Pace Edwards Ultra Groove tonneau cover. This provides you with a ladder rack that uses Yakima HD bars. Then you also want to use the HD bars on roof rack towers to provide a lower rack using the t-slots in your Ultra Groove Rails. In that case, the Landing Pad 4 for Yakima SkyLine and...
  view full answer...
• Will Yakima Landing Pad 1 and 4 Fit Rhino-Rack RTC-Style Roof Rack Tracks
  Yes, I test fit the Rhino-Rack RTC-Style Roof Rack Tracks # RTC12JW with the Landing Pad 1 # Y00221 and the Landing Pad 4 # Y00224 and found that they are compatible with each other. All of these parts come in a quantity of 2. To complete your setup you also need 4 of the Yakima Control Tower # Y8890027 and a set of round bars that match your application. We have a variety of round bar lengths for you to choose from. These include the following: 48" Round Bars - # Y00408 58" Round Bars...
  view full answer...
• Recommended Yakima Roof Rack for 2007 Land Rover LR3 with Factory Track System
  The Thule Fit Kit # THKIT3112 is the confirmed fit for your 2007 Land Rover LR3. Since they do not fit in the way you desire, I recommend the Yakima Landing Pad 4 for Yakima Control Towers - Qty 2 # Y00224 ( you will need 2 kits), the Skyline towers # Y53TR and the Jetstream Crossbars # Y00425. I also recommend the locks to secure your roof rack # Y07204. This system will mount differently into your factory rails for a confirmed fit.
  view full answer...
• Recommended Crossbars and Roof Basket for a 2008 Hummer H3 With Factory Rails
  For your 2008 Hummer H3, I recommend checking out the Yakima MegaWarrior Extra Large Roof Rack Cargo Basket # Y07080-82. This cargo basket will easily attach to a set of crossbars like the Yakima HD Crossbars # Y01156, measures 74" long x 48" wide x 6-1/2" tall, and has a maximum weight capacity of 130-lbs. To finish the crossbar setup, you'll also need the SkyLine Towers for Yakima Crossbars # Y53TR, HD Bar SL Adapter for Yakima BaseLine, SkyLine, TimberLine, and RidgeLine Towers #...
  view full answer...
• Landing Pads For Rails Of A Carry On Utility Trailer For Yakima Control Towers
  If the rails you are referring to on your utility trailer are the track style, then your Yakima Control Towers will fit with Landing Pad 4 for Yakima Control Towers - Qty 2 # Y00224. If you will me drilling into metal support rails then you will want the Landing Pad 7 for Yakima Control Towers for Metal Roofs - Qty 2 # Y00227. You may also be interested in the Round 78" CrossBars for Yakima Roof Rack System (QTY 2) # Y00411 or the Round 86" CrossBars for Yakima Roof-Rack System (QTY 2)...
  view full answer...
• Roof Rack Recommendation for a 2008 Hummer H3 with Factory Tracks
  For a roof rack that is confirmed to fit the tracks on your 2008 Hummer H3 you would want the Yakima part numbers # Y00408, # Y53TR, # Y03536, and # Y00224. You can also lock this rack with the lock core set part # Y07204 which would help prevent theft. Sorry to hear about your factory rack getting stolen.
  view full answer...
• Replacement Yakima Landing Pad For Roof Rack Tower
  The landing pad you have is either going to be in the kit Landing Pad 1 # Y00221 or Landing Pad 4 # Y00224. The landing pad 1 has a more square shaped channel nut while the landing pad 4 has a more rectangular channel nut.
  view full answer...
• Roof Rack for 2007 Hummer H3 with Roof Rack Channels
  For your 2007 Hummer H3 with the roof tracks like you pointed out we have the Yakima Skyline roof rack part numbers # Y00425, # Y53TR, and # Y00224 as a confirmed fit. This attaches to the slots you have and gives you a high quality rack that due to it's bar shape will be very aerodynamic.
  view full answer...
• Parts Needed to Carry Spare Wheel on Roof of 2008 Hummer H3
  If you installed a Yakima roof cargo basket like the # Y07070 you could use the Spare Tire Carrier part # Y07076 to carry the spare on your roof. You would need a roof rack installed on your 2008 Hummer H3 as well like the Yakima round bar roof rack part # Y00408, # Y53TR, # Y03536, and # Y00224. We don't have a good solution to cover where the old spare was installed. If you make it near St. Louis MO we could help out with the install too!
  view full answer...
• Roof Rack Recommendation for 2005 Chrysler Town and Country Van
  Your 2005 Chrysler Town and Country van could be equipped with three possible roof configurations (factory tracks, raised side rails or nothing at all). From your description is sounds like you have the factory tracks. For this roof style we have rack options that can be seen on the link provided. A cost-effective basic round bar system is offered from Yakima and consists of parts # Y00408, # Y00224, # Y53TR and # Y03536. Round bars offer excellent compatibility with accessories like bike...
  view full answer...
• Roof Rack Recommendation for 2009 Hummer H2
  For a 2009 Hummer H2 we have the Yakima Roof Rack part numbers # Y00409, # Y53TR, # Y03536, and # Y00224 which is a confirmed fit and will work well. We don't have anything for a 2011 model as there wasn't a 2011 model made in the US nor do we have anything that was made by Hummer.
  view full answer...
• How to Install Rhino-Rack Pioneer Platform Rack on a 2003 Hummer H2
  To install a platform rack on your 2003 Hummer H2 we first need a roof rack and for that I recommend the Yakima JetStream system that includes the following parts: - 60" JetStream Crossbars # Y00426 - SkyLine Towers # Y53TR - Landing Pad 4 # Y00224 This installs directly to the fixed mounting points on your Hummer which then allows you to use the Rhino-Rack Pioneer Platform Tray # RR82TB along with 2 of the Mounting Kit # RR43105 to get it installed. The Pioneer Platform # RR85ZW...
  view full answer...
• Roof Rack Fits for 2003 Chevrolet Suburban
  The current Yakima round bar roof rack that fits your 2002 Dodge Grand Caravan consists of parts # Y00408, # Y53TR, # Y03536 and # Y00224. All roof rack fits for the 2003 Suburban are shown on the linked page but no Yakima branded racks are among them. You can select your roof type using the drop-down menu tool at the top of the page to see roof racks that will work on your 2003 Suburban. If you have factory roof tracks then a cost-effective square bar rack confirmed to fit is the Inno...
  view full answer...
• Roof Rack Spacing On Roof Of 2006 Dodge Caravan With Sliding Doors
  When installing the Yakima roof rack on your 2006 Dodge Caravan with the sliding doors, the location of the feet and bars is not something that can be adjusted for each load. They are designed for a specific location so you would need to use other accessories like a roof basket for your specific load to give further support. To order the roof rack custom made for your Caravan, you will need part # Y00425, # Y53TR, and part # Y00224. I have attached a product review video for this roof...
  view full answer...
• Parts Needed to Carry the Thule Roof Mounted Cargo Basket # TH859XT on a 2005 Dodge Caravan
  To carry the Thule Canyon XT Roof Mounted Cargo Basket # TH859XT on your 2005 Dodge Caravan you will just need a roof rack (if you don't already have one). The Thule basket is compatible with round, square, aero, elliptical, and most factory crossbars. Should you have the factory installed tracks that front to back I recommend the Yakima roof rack which consists of their JetStream Crossbars # Y00425, the SkyLine Towers # Y53TR, and the Landing Pad 4 # Y00224. For a 2005 Caravan that has...
  view full answer...
• Recommended Bike Carrier for Hummer H3
  The Swagman Pick-Up Truck-Bed-Mounted Bike Carrier is designed for pick up truck beds, so it is not a fit for your Hummer H3. However, I do have several bike carrier options for your Hummer. Our most popular bike rack for the Hummer H3 is the Swagman Original # S64400 4 Bike Rack for 2" Hitches. I have linked to a video review of the bike rack for you to check out. I have also linked you to a FAQ article that shows how to measure the distance between your hitch pin hole and the furthest...
  view full answer...
• Recommended Roof Rack and Mud Flaps for 2007 Hummer H3
  For your 2007 Hummer H3, I recommend the Yakima JetStream Roof Rack, which consists of parts # Y00425, # Y00148 and # Y00224. This rack features two 50 inch, aerodynamic crossbars with a weight capacity of 165 pounds. They have a lightweight, durable and rustproof aluminum construction that will be perfect for your particular driving conditions. The asymmetrical shape will provide an extremely low profile and quiet system when installed on your Hummer. The SkyLine Towers will attach to...
  view full answer...
• Recommended Roof Rack for a 2012 Land Rover Range Rover Sport
  The roof rack I recommend for a 2012 Land Rover Range Rover Sport will be dependent on roof configuration. If you have a bare roof then I recommend the Thule WingBar Evo Crossbar System part # TH711520, part # TH710501, and part # TH145116. If you have factory installed tracks then I recommend the Yakima Jetsream Crossbar System part # Y00426, part # Y53TR, and part # Y00224. These are both excellent top-of-the-line options.
  view full answer...

Do you have a question about this Roof Rack?