Replacement Trailer Hubs Using L68149 and L44649 Bearings

Question

Question:

i have measurements on my hubs. i need 2 replacement hubs. can you tell me which ones? .99 at threads, outer 1.06, inner 1.378, seal 1,737

asked by: David A

0

Expert Reply:

It sounds like you have inner and outer bearings # L68149 and # L44649 respectively. That's a very popular combination on a # 84 spindle but the seals are normally 1.719 inches inner diameter. I would verify that number.

If this is correct there's a still a number of options that could be your correct hubs depending on whether you have drums, what bolt pattern they are, and whether you have EZ Lube spindles or not. I'll list all the optoins for you.

5 on 4-1/2 bolt pattern:

Standard spindle idler hub part # AKIHUB-545-35-K
E-Z Lube spindle idler hub part # AKIHUB-545-35-EZ-K

Standard spindle hub and drum part # AKHD-545-35-K
E-Z Lube spindle hub and drum part # AKHD-545-35-EZ-K

6 on 5-1/2 bolt pattern:

Standard spindle idler hub part # AKIHUB-655-35-K
E-Z Lube spindle idler hub part # AKIHUB-655-35-EZ-K

Standard spindle hub and drum part # AKHD-655-35-K
E-Z Lube spindle hub and drum part # AKHD-655-35-EZ-K

These aren't the only bolt pattern options but they're the most common by far. If yours is different or something else doesn't add up let me know. Also, if you aren't sure of your bolt pattern I've added an article to help you determine what you have.

expert reply by: Charles S

0

Answer 1

Sup Jesse - cool name! The #AKHD-545-35-EZ-K hub is going to use the 1.98" bearding buddies. For that we have #BB1980A for chrome or #BB1980A-SS for stainless Steel, which is what I recommend.

view full answer...

Answer 2

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 3

The exact replacement for the hub you have is the part #84545UC1-EZ. This will install on your spindle and has a 5 on 4-1/2 inch bolt pattern like you need as well.

view full answer...

Answer 4

Yes the Timbren Axle-Less Trailer Suspension System #ASR1THDS01 will work with Dexter Trailer Idler Hub Assembly #84545UC1-EZ. The idler hub can mount a 15" wheel, and has a 5 on 4 1/2" bolt pattern for the lugs which are 1/2" in…

view full answer...

Answer 5

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 6

The next largest size is #RG04-040 which has an OD of 1.99 inches. If you can provide me with the reference number from your outer wheel bearing, I'd be happy to check into the availability of a suitable grease cap.

view full answer...

Answer 7

The Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased is offered with two different grease caps, part #AKHD-545-35-K for standard or part #AKHD-545-35-EZ-K for easy lube spindles. I suppose you could order…

view full answer...

Answer 8

Your trailer likely uses bearings #L68149 and #L44649 but you should check them to be sure. If this is the case I recommend hub and drums #AKHD-545-35-EZ-K if you have E-Z Lube axles with the zerk fitting on the spindle. If you don't have E-Z…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

As long as the seal in the bearing kit part #BK1-150 is flush with the hub it is okay to have a small gap between the seal and inner bearing. When installing the seal you only insert it enough so that it is flush with the hub. The seal's job is…

view full answer...

Answer 11

A true 1 inch spindle is a BT8 spindle, like #TRU94FR. The next closest one would be the BTR spindle which is commonly referred to as a 1-1/16 inch spindle, like #TRU44FR and is more common than the BT8. Both of these are typically used with 2,000 lb…

view full answer...

Answer 12

If you know the trailer axle capacity that's a pretty good way to determine what spindle you have. Or if you get me the bearing numbers. You can also measure the spindle where the bearings ride and with that info I can let you know what you…

view full answer...

Replacement Trailer Hubs Using L68149 and L44649 Bearings

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching