Looking For Replacement Trailer Hubs For 5 on 4-1/2" Lug Pattern With LM11949 Bearing And LM11910 Ra
Updated 07/17/2024 | Published 07/10/2024
Products Featured in This Question
Question:
I am looking for a pregreased hub assembly for a straight spindle 3/4” 5 stud 4 1/2” trailer. The bearing and racers on old hub is LM 11949 and LM11910. Do you have this?
asked by: Jason
Expert Reply:
Hey Jason, LM11949 is a bearing that works with LM11910 race, and we do have idler hubs that match these specs while also fitting your 5 on 4-1/2 lug pattern. That said, you'll also want to check the inner bearing to verify that it is LM67048 (1.25" inner diameter). If it is, then Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 # DX22XR is the correct idler hub.
Keep in mind, these are not pre-greased so you will have to do that when they arrive. It is not hard to do by hand with LubriPlate Poly HP-2 Wheel Bearing Grease # L11465, but you can also make it easier by user a bearing grease packer like Powerbuilt Deluxe Bearing Packer # ALL647646.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- LM67048 / LM11949
- Standard Grade
- For 2500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: pre greased hub
- Shop: Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Search Results: timken bearing kit
- Search Results: trailer hubs and drums
- Search Results: tapered spindle hub
- Search Results: bearing grease
- Shop: Loadstar ST185/80D13 Bias Trailer Tire - Load Range D
- Search Results: trailer hub
- Search Results: trailer bearings races seals caps
- Q&A: Hub and Drum Assembly for 1 1/4 inch by 3/4 inch Axle
- Q&A: 5 on 4-1/2" Idler Trailer Hub For Utility Trailer With 1-1/4" to 3/4" Tapered Spindle
- Q&A: Is There A Hub/Drum Assembly That Uses The Same Bearings And Seals As The Dexter DX22XR
- Q&A: Availability Of Trailer Hub With .75" Outer And 1.25" Inner Bearings
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Dexter Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Trailer Hub Assembly - 3,000 lbs Axles - 4 on 5 - Agricultural
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Idler Hub - AKIHUB-545-35-K
- Q&A: Pre-Greased Hub Assembly with L44649 Inner and Outer Bearings
- Q&A: Should There Be A Gap Between The Seal and The Inner Bearing In My Hub
- Video: The Low-Down on the Timken Bearing Kit, 15123/25580 Bearings, 15245/25520 Races, 413470 Seal
- Q&A: Replacement Trailer Hubs Using L68149 and L44649 Bearings
- Video: Complete Breakdown of the Trailer Idler Hub Assembly for 2K Axles
- Video: Feature Review Loadstar ST185/80D13 Bias Trailer Tire
Jason
7/17/2024
I might not have made this clear. Both inner & outer bearing & racers are the LM11949 & 11910. The spindle is a straight 3/4” spindle it does not taper. I would need the whole hub assembly. Bearings, seals, racers, cap, & hub. Its for a 1982 shorelander trailer with i believe 10 or 12” tires.