Trailer Hub That Uses Bearings LM11949 and LM67048
Updated 10/23/2017 | Published 10/21/2017
Products Featured in This Question
Question:
I put on new electric brakes on my trailer, the mount had the four bolt backing plate, and realized the hub/drums that were on there were only for hydro brakes so i need new drums. the innner diameter of my innner bearing is 1.25in and the inner diameter of the outer bearing is .75in as measured with my electronic caliper. there was no number i could see stamped on the bearing, it is on a tandem axle tilt bed trailer with 5 on 4 1/2 bolt pattern.
asked by: Brian F
Expert Reply:
Both replacement trailer brakes and hub/drums should be selected based on the axle weight rating.
The best way to select replacement hub/drums is to pull one of the hubs and remove its inner and outer bearings to obtain their part numbers. This is the easiest method to find a compatible hub. When not available measurements can be used but these need to be very precise, to the nearest thousandth of an inch, such as 1.234-inches.
We do carry one bearing with an inside diameter of 0.75-inches, part # LM11949, which is typically rated for a 3K axle. We have several bearings with an inside diameter of 1.25-inches, all shown on the other linked page. These bearings are typically found on a higher-rated axle, one in the 5K to 8K range.
None of our 5-on-4-1/2-inch bolt pattern hub/drums use these bearings but we do have one 5-on-4-1/2 idler hub, part # DX22XR, that does use bearings # LM11949 and # LM67048.
Product Page this Question was Asked From
Replacement Trailer Wheel Bearing - LM11949 - Qty 1
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- .75 Inch I.D.
- Bearing LM11949
- Race LM11910
- 3000 lbs Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter Trailer Idler Hub Assembly for 2,500-lb Axles - 5 on 4-1/2
- Shop: Trailer Hitch
- Shop: Base Plate for Tow Bar
- Search Results: 2500 lb trailer axle
- Q&A: Replacement Trailer Hubs For Spindle That Uses 1-1/4" Inner Bearing and 3/4" Outer Bearing
- Q&A: Replacement Hub/Drum Assembly Needed For A Older Boat Trailer
- Q&A: Recommended Trailer Hub with 1-1/4 Diameter Inner Bearing and 3/4 Diameter Outer Bearing
- Q&A: Trailer Hub Availability that Uses Bearing Numbers LM67048 and LM11949
- Q&A: Trailer Hub That Fits a Spindle With 1-1/4" Inner Bearing and 3/4" Outer Bearing
- Q&A: Removing and Replacing Trailer Spindles
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Trailer Hub Assembly - 2,200-lb E-Z Lube Axle - 5 on 4-1/2 - 13" - 15" Wheels - Galvanized
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Shop: Agricultural Spindle for 3,000-lb Trailer Axles - 1-5/8" Diameter
- Shop: Dexter Trailer Idler Hub Assembly for 2,700-lb Axles - Pre-Greased - 5 on 4-1/2 - Galvanized
- Search Results: spindle
- Search Results: 3/4 inch axle hub
- Search Results: dx22xr
- Shop: Vehicle Tow Bar Brake System
- Search Results: trailer hitch
- Search Results: 49090
- Search Results: 9599018
- Q&A: What Fuse of 2012 Honda CR-V Needs to be Removed to Flat Tow
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
on Trailer Bearings Races Seals Caps
