Trailer Lights

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…

Hey Darren, the studs of the Optronics Fusion LED Trailer Light #OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to…

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…

Hey Sal, the Optronics Fusion LED Trailer Light #OPT45KB is for just 1, not set of 2. These are super nice, but if you want some other options to consider, we also have the Fusion LED Hardwired Trailer Light #OPT57NR which does have the same…

Hey Eli! The first thing you want to do is make sure you have brake flanges on those axles. You also need to take a look at the axle tags and find the axle capacity. More than likely they're 3,500 lb axles so I'll answer based on that. If you…

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…

Hey Steven! I measured the Peterson LED Clearance and Side Marker Light #PET95FJ using a caliper and the measurements with the grommet came out to 1.91" tall and 3.26" wide. Rounded to the nearest fraction on a tape measure, that would come…

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…

Hey Darren, the studs of the Optronics Fusion LED Trailer Light #OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to…

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…

Hey Sal, the Optronics Fusion LED Trailer Light #OPT45KB is for just 1, not set of 2. These are super nice, but if you want some other options to consider, we also have the Fusion LED Hardwired Trailer Light #OPT57NR which does have the same…

Hey Eli! The first thing you want to do is make sure you have brake flanges on those axles. You also need to take a look at the axle tags and find the axle capacity. More than likely they're 3,500 lb axles so I'll answer based on that. If you…

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…

Hey Steven! I measured the Peterson LED Clearance and Side Marker Light #PET95FJ using a caliper and the measurements with the grommet came out to 1.91" tall and 3.26" wide. Rounded to the nearest fraction on a tape measure, that would come…

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…