Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The #AL91RB and #AL91AB will work with the Mounting Bracket #A91BB and then for a pigtail you can use the Right Angle…
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…
Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
Stuart, since you’ve already confirmed the truck and trailer wiring through the junction box and verified the grounds, the fact that the running lights, brake lights, backup lights, and turn signals all work individually points us toward the tail…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Hey Mike! We don't have an all-in-one part that comes with the brackets and pigtail so you need to order those parts separately. The #AL91RB and #AL91AB will work with the Mounting Bracket #A91BB and then for a pigtail you can use the Right Angle…
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Trailer Lights with Reflectors for confident visibility
Light up your rig's outline and boost nighttime visibility by pairing trailer lights with reflectors. Choose stick-on pieces or conspicuity tape to mark frames, gates, steps, or racks; each segment of red or white marking tape must be from 6" to 18" long, and reflectors can be installed in a repetitive pattern of 2 or 3 white reflectors alternating with 2 or 3 red reflectors with the center of each not more than 4" from the next.
Pick shapes and colors that match your existing reflectors; red and amber options are common. For stick-on styles, clean and dry the surface and apply firm, even pressure. If you expected a raised dome but got a flat reflective sticker, verify the style before ordering. If an adhesive-backed unit loosens, replace it and consider a screw-on style for that location.
Yes, reflectors can be used in place of tape when installed in the right pattern. Use a repetitive pattern of 2 or 3 white reflectors alternating with 2 or 3 red reflectors, with centers no more than 4" apart. If you use tape instead, segments of red or white should be 6" to 18" long, and in a continuous strip one color can't exceed 2/3 of the total length.
Add reflectors where they'll catch headlights directly. Mounting them on the back side of light boxes or a drop-down gate made a low utility trailer easier to see while backing at night. Clean the surface and align them at driver eye level when possible. Check that the adhesive is fully set before use.
Stick-on reflectors can hold very firmly and be super reflective. They've stuck well to slick surfaces and can be hard to remove without a scraper. Clean the mounting area before applying and press firmly. If you notice an adhesive failure or a reflector separating from its backing, replace it and consider a different mounting style for that spot.
Oblong
Oval
Rectangle
Round
Trailer Lights Parts or Accessories
Filters
