Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…
Hey Eli! The first thing you want to do is make sure you have brake flanges on those axles. You also need to take a look at the axle tags and find the axle capacity. More than likely they're 3,500 lb axles so I'll answer based on that. If you…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Hey Darren, the studs of the Optronics Fusion LED Trailer Light #OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to…
Hey Aaron, it sounds like you are looking for an awning rail, is that correct? For that we have the P and F awning rail part #PF88FR which is compatible with the Solera awnings.
Hey Rick. Unfortunately that's correct the Wesbar Tail Light 271594 has been discontinued. Our best option for replacing it is the LED Trailer Tail Light item #STL36RB for the passenger side and item #STL37RB for the driver side. The Wesbar light…
The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…
We sure do Brian. We've actually got two center caps that are going to work with the Kenda Karrier KR53 ST205/75R15 Radial Trailer Tire with 15" Black Aluminum Wheel item #KE58JV. Which one you go with is going to come down to personal…
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Robert
Bloomington, IL
Rampage Trailer Lights for your setup
Looking for a straightforward light system that does the job? Rampage trailer lights keep things simple and practical for everyday towing. They're at home on a trailer and can even go on the back of a scooter for added rear lighting when you need a versatile solution.
Yes, they can be mounted on the back of a scooter. Verify you have a solid spot to secure the straps and enough room for the lights. Once fitted, check that the attachment stays put through a few bumps before heading out.
Some Rampage trailer light setups include strapping for attachment. Check how the straps route and tighten on your trailer or gear, then do a quick pull test to confirm they're snug. If the strapping feels uncertain, re-position and re-tension until it holds the way you want.
Installation can be straightforward. One setup went right onto the back of a scooter, while another needed a bit of adjustment to the strapping to make it work. Plan a test fit and take a minute to dial in strap tension so the lights stay secure.
Match the mounting method to your setup. If the system uses strapping, confirm you have anchor points and enough strap length. For smaller applications like a scooter, make sure there's flat space and clearance for the lights to sit securely.
Filters
