In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
...this particular light is on indefinite backorder. I recommend replacing both of your lights with a similar light like the Optronics # STL36RPG and # STL37RPG.
These lights have a wraparound style like...
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
Hey Keith, sorry for confusion but the TecNiq Round Side Marker Light #TN54TR that you referenced does not come with a grommet and you'd need that separately with the part #TN43TR.
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
Hey Pete, we can help but there aren't any custom fit gooseneck hitches that fit your 2008 Chevy Silverado but we can still help. The B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks - 30,000 lbs #BWGNRK1500 has multiple…
Todd, you’re in good shape. The Firestone Air Bag Kit #F44XV kit is a confirmed fit on 2WD or 4WD 2025 F-250s, and it is compatible with in-bed hitches, including goosenecks. Firestone’s brackets mount to factory locations on the frame, and nothing…
...and item # STL37RB for the driver side.
The Wesbar light is about 7" long x 3-3/4" tall x 3" deep. These Optronics lights are 7-7/8" long x 3-1/4" tall x 2-7/8" deep, so they are slightly longer than...
You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
...this particular light is on indefinite backorder. I recommend replacing both of your lights with a similar light like the Optronics # STL36RPG and # STL37RPG.
These lights have a wraparound style like...
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
Hey Keith, sorry for confusion but the TecNiq Round Side Marker Light #TN54TR that you referenced does not come with a grommet and you'd need that separately with the part #TN43TR.
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
Hey Pete, we can help but there aren't any custom fit gooseneck hitches that fit your 2008 Chevy Silverado but we can still help. The B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks - 30,000 lbs #BWGNRK1500 has multiple…
Todd, you’re in good shape. The Firestone Air Bag Kit #F44XV kit is a confirmed fit on 2WD or 4WD 2025 F-250s, and it is compatible with in-bed hitches, including goosenecks. Firestone’s brackets mount to factory locations on the frame, and nothing…
...and item # STL37RB for the driver side.
The Wesbar light is about 7" long x 3-3/4" tall x 3" deep. These Optronics lights are 7-7/8" long x 3-1/4" tall x 2-7/8" deep, so they are slightly longer than...
You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Optronics LED trailer lights are a top choice for enthusiasts looking to upgrade their lighting. Known for their brightness and easy installation, these lights are perfect for replacing dim incandescent bulbs. Whether you're upgrading an RV, horse trailer, or utility bed, Optronics offers reliable, energy-efficient lighting solutions.
Optronics LED lights are praised for their brightness and energy efficiency. They offer a significant improvement over incandescent lights, drawing less power and providing a brighter, more reliable light. They're easy to install, often fitting directly into existing mounts, making them a great choice for DIY upgrades.
These lights excel in various trailer types, from RVs to horse trailers. They provide excellent illumination for loading and unloading, and their bright, white light enhances visibility. Users have noted their effectiveness in both interior and exterior applications, making them versatile for any trailer setup.
Installation is straightforward, often requiring just a plug-and-play setup. However, ensure you have the necessary grommets and pigtails for a secure fit. Taking time with the layout and using the right tools, like a hole saw for mounting, can make the process smoother and ensure a watertight seal.
Switching to LED lights reduces power draw significantly, from 14.5 amps to just 2.5 amps, which is easier on your trailer's electrical system. LEDs also offer a longer lifespan and a brighter, more consistent light output, enhancing safety and visibility during night-time operations.
Yes, Optronics LED lights are versatile and can be used for both brake and backup lights. They provide a bright, clear signal that improves safety on the road. Their design allows them to fit over existing mounts, making them an ideal choice for upgrading both functions simultaneously.
Filters
