Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you’re parked for the night, a steady base makes all the difference. This set includes two steel scissor jacks rated at 5,000 lbs each, giving you a combined 10,000-lb capacity to stabilize your trailer or camper. They raise and lower smoothly, keeping your setup level and solid so you can move around inside without the shake or sway.
Campsites and storage lots aren’t always level, but these jacks make it easy to adapt. Each one adjusts from a compact 4" retracted height up to 24" extended. The wide bow-tie base keeps the jack steady on soft surfaces like dirt or sand so you don’t have to hunt for extra blocks or boards.
Whether you prefer to bolt directly to existing brackets or weld them on for a permanent setup, these jacks are ready for either. The mounting tabs include elongated holes for flexible spacing, making installation straightforward with basic tools. Once mounted, crank them up or down using the included handle whenever you need to stabilize your trailer.
These jacks are made of sturdy steel to handle years of real use at the campsite or in storage. The design focuses on durability and stability rather than bulk, so they hold strong without taking up extra space underneath your rig. Each pair comes backed by a 1-year limited warranty for added peace of mind when you’re setting up anywhere.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today you'll be getting a look at and seeing how to install the Stromberg Carlson Leveling Scissor Jack Set, with a quantity of two, part number JSC-24. They're also available in a quantity of one, with part number JSC-24-IND.You can bet on this pair of jacks. These scissor jacks from Stromberg Carlson are great for stabilizing and leveling your camper. As you can see, if your trailer is out of level, you can use your scissor jacks to level it. Check it out. Much better.
As you can see, without your scissor jacks engaged, there's a lot of movement in your trailer. With your scissor jacks engaged, all that extra movement is gone. They're adjustable between four and 24 inches and they have a 5000 pound weight capacity per jack. You can easily raise and lower them with the included crank handle. It's going to work out great on most surfaces.
As you can see, we're on concrete here. The bow-tie base is going to keep it steady even on soft surfaces.They're a bolt-on or weld-on installation. We'll go ahead and show you how to bolt them on now. Here you can see our old rusted out stabilizer jack. It's bent.
We're going to be replacing it. I've gone ahead and removed the old stabilizer. Let's bring in our new one. With our new one, you can see it's got multiple mounting locations. It's completely universal.
Now, you may or not be able to use your same mounting holes and locations. What you need to do is hold it up and figure out where it's going to work best. Now, once you've found a good location to install your stabilizer jack, you want to be sure that you can still easily access your drive nut, which is going to raise and lower your stabilizer jack.You'll want to raise your jack up to where it's making contact with your frame where you want to install it. Then you can mark your holes. Now, there are six holes on each side. I'm only going to be using four total, two on each side. You can use whichever holes work out best for you. Once you've got your holes marked, go ahead and move the jack out of the way, and then you can begin drilling out your holes. I'm going to be drilling out quarter-inch holes. If you'd like to, you can use a pilot bit and then drill out your final size. All right. With all those drilled out, you can go ahead and install your stabilizer jack. You will have to provide your own hardware.I'm just using some quarter-inch bolts with some flat washers and lock nuts. Now you can bring your jack back in and align your holes. Now you'll just loosely install all your hardware. Now we can tighten up our hardware. Now you can raise up your jack and it's ready for when you need it. That's going to complete your look at the Stromberg Carlson Leveling Scissor Jack set.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews
Sue R.
9/3/2017
Working just fine, plan on buying two more for another trailer.
Dan B.
8/1/2016
The Jack stabilizers are working out great on my camper, I had them welded on and I use a socket on my cordless drill to crank them up and down.
Bob C.
9/6/2017
No problems. Product works great.
Michael A.
8/4/2016
I just returned from a month long vacation trip on which I used the Stromberg Carlson jacks every day except two. I have not had any issues with the Stromberg jacks as they are the quality I am wanting.
Lindsay
6/9/2024
I have been using these camper jacks for a year now and love them. These are a very sturdy upgrade over the factory installed jacks.
Do you have a question about this Camper Jack?
Condition: Badly Dinged
Notes: Item has minor cosmetic scratches and has slightly bent mounting tabs that can be bent back into place.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
3/28/2022
You mentioned that the welds had broken and i wanted to ask if you would be able to send a picture of them?