Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1

Ask the Experts about this etrailer Camper Jacks

• Looking for Replacement Stabilizer Scissor Jack for RPod 179
  The stabilizer jacks aren't trailer specific, but the mounting hole spacing is pretty standard across the board. I'd recommend removing the damaged jack and comparing the mounting plate hole spacing to what's shown in the provided photos. The # TJSC-24 or the # UF48-979006 are likely fits as the hole spacing is pretty similar between the two. The # UF48-979006 has a 6500 lb capacity and a 24 inch lift while the # TJSC-24 has a 2500 lb capacity and a 18-3/4 inch maximum lift. I've linked...
  view full answer...
• How to Determine if Scissor Jack Will Fit Camper
  The Scissor Stabilizer Jack # TJSC-24, which also comes in a 2-pack # TJSCHD-24 and a 4-pack # TJSCHD-24-4, is a universal fit so you would need to double check our measurements to ensure they fit your travel trailer. When they are collapsed they measure 5" tall and then they can extend up to 23-3/4" tall to help stabilize your trailer. I am attaching a link to our returns policy that you can reference in regards to your question about a possible return.
  view full answer...
• Recommended Scissor Jack for Boat Trailer
  We do have a nice selection of scissor jacks available like the Ram # TJSC-24 that you referenced, however none of them feature an aluminum or stainless steel construction. These scissor jacks do have a black powder coated finish though that will do a really nice job of resisting corrosion. They have a weight capacity of 2,500 pounds and will work well for your application to add stability to your parked trailer. Another potential option is the Ultra-Fab Stackable Stabilizers # UF48-979004....
  view full answer...
• Can The Frame Of the Trailer Be Installed In the Slot On the Scissor Stabilizer Jack
  In regards to the Scissor Stabilizer Jack part # TJSC-24, the slot is not designed to support the frame. I must recommend you attach the two ears to the bottom of the frame as you can see in the attached video. I have also attached for you some general dimensions of said ears below as well.
  view full answer...
• Replacement Stabilizer Jacks for Forest River R-Pod 190
  The Scissor Stabilizer Jack # TJSC-24 would be a great solution and what I recommend if you're looking for a stabilizer jack that provides 18-3/4" of extension for 23-3/4" of total lift. These can be used as either front or rear stabilizers and are designed to hold up to 2500-lbs of weight. These stabilizers are sold as a pair, so you'll be able to replace both of the rear stabilizers on your R-Pod 190 travel trailer.
  view full answer...
• Replacement Scissor Jacks for Starcraft Launch Ultra Lite
  We have great stabilizer jacks sold in pairs that would work great on your 2015 Starcraft Lanch Ultra Lite with the part # e99012. These have a weight capacity of 5,000 lbs and a lift height of 24 inches.
  view full answer...
• Stabilizer Recommendations for 2016 Rockwood Ultra Lite
  For a travel trailer like your 2016 Rockwood Ultra Lite the best solution to prevent the movement is the Electric Ground Control TT system part # LC672136 which with the push of a button will level and stabilize the trailer better than other options. But it's not a cheap solution. Scissor jacks like the part # TJSC-24 are one option but like you found they don't totally get rid of the movement as well as something like the Ground Control or something like the Ultra Fab # UF39-941704.
  view full answer...
• Alternate to Obsolete Atwood Stabilizer Jack 82301
  There is absolutely an alternative to the Atwood 82301, stabilizer jack you referenced. That particular jack had a 650 lb lift capacity, 1,000 lb support capacity, 3" center to center mounting holes, a retracted height of 11-1/2" and an extended height of 17-3/4" for 6-1/4" of drop leg travel. Any type of stabilizer jack with similar capacities will work, such as the Ram Scissor Stabilizer Jack # TJSC-24. It has a 2,500 lb lift capacity, a collapsed height of 5" and extended height...
  view full answer...
• Replacement Scissor Jack for a 2008 KZ Coyote Lite CL168
  We have exactly what you need. I was able to confirm that your Gross Vehicle Weight Rating for your 2008 KZ Coyote Lite CL168 is 4000lbs. With that said using 4 of Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs gives you a total weight rating of 10,000 lbs which is more than enough to handle the job. The Etrailer Scissor Stabilizer Jack - 18-3/4" Travel Part # TJSC-24 is the way to go as long as the frame of your camper is not more than 23 3/4 inches form the ground. These are...
  view full answer...
• Replacement Scissor Jack for a 2016 R-Pod 178 Trailer
  It does appear that your 2016 R-Pod 178 uses the Ram scissor jack, # TJSC-24, so it would be the correct replacement. Should you also ever need a replacement handle it is # TJSC-24-HD.
  view full answer...
• Jack for Tire Replacement on Lifted Jeep
  Our scissor jacks should not be used to lift a car to replace a spare tire as they were not designed for that application. Instead, depending on how far you need to lift, you may be able to use the Powerbuilt Unijack # ALL620470, which can lift up to 4,000 lbs and a range between 8-5/8" and 18-3/8", or Powerbuilt Unijack # ALL620471 which has a lift capacity of 6,000 lbs and a lift range between 11" and 21". After lifting your vehicle the jack locks into place with a safety bar so you would...
  view full answer...
• Replacement Stabilizer Scissor Jack for 2018 Forest River R-Pod 189
  The R-Pod 189 usually comes fitted with four corner-mounted scissor jacks that bolt to the frame. We have a number of such bolt-on stabilizer jacks that are shown on the linked page. Many of these are sold as pairs but we also have single jacks too, such as the item you referenced, part # TJSC-24, which offers up to 18-inches of extension. This 2500-lb-rated item has plenty of weight capacity for stabilizing one corner of your 189 so as long as the extension matches your other jacks...
  view full answer...
• Recommended Jack to Change Tires on a Trailer
  Scissor jacks for trailers or RVs such as # TJSC-24 are not meant to lift the trailer/RV off the ground. They are meant as support only. What I recommend is a bottle jack such as # ALL647501. This is a 24,000 pound jack that has a lift range of 8-1/4 inches to 16-5/16 inches. Need more lift? Bottle jack # ALL647503 is rated for 40,000 pounds and has a lift range from 9-11/16 inches to 17-5/8 inches. The great thing about bottle jacks is they are compact, easy to store, and can also be...
  view full answer...
• Will Ram Scissor Jack # TJSC-24 Work on R-Pod Travel Trailer
  The Ram Scissor Jacks part # TJSC-24 weigh 12 lbs. These would work great on your R-Pod travel trailer. These are universal in design and will easily install on your 179 camper.
  view full answer...
• Hole Size and Spacing on the Foot of Ram Scissor Stabilizer Jack - 2,500 lbs. # TJSC-24
  I went out to the warehouse to measure the hole diameter and spacing on the foot (base) of the Ram Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Item # TJSC-24. The holes are 1/2 inch in diameter and are spaced 6-13/16 inches apart on center.
  view full answer...
• Replacement Rear Scissor Jack Recommendation for R-Pod 180 Camper
  The R-Pod 180 that you have has scissor jacks attached to the frame in all four corners of the trailer. Since it looks like your trailer sits pretty high off of the ground the pair of jacks I recommend are the Ultra Fab # UF48-979031 which have 30 inches of lift and a stabilization capacity much higher than your trailer would require at 6,500 lbs.
  view full answer...
• Stabilizer Scissor Jack for Winnebago Micro Minnie 1706 fb that has Proper Height Range
  Sounds like the reason your current scissor jacks aren't able to stabilize your trailer effectively is because your trailer is taller than it's height range. Your best solution will be a scissor jack setup that has a higher height range like the Ultra Fab kit part # UF48-979002 which can provide up to 24 inches of height and will make a huge difference in stabilizing your trailer. I attached a review video for more info on this as well.
  view full answer...
• Will Scissor Stabilizer Jacks Work on Flagstaff T12RBST Trailer
  I have no doubts the Scissor Stabilizer Jack # TJSC-24 will work as a perfect replacement for the scissor stabilizer jacks on your 2017 Flagstaff T12RBST camper trailer because it has a large 10" x 3-1/4" mounting base with numerous different bolt hole options, as you can see by the cut out of the base I added. It also has a 2,500 lb capacity and extended height of 23-3/4" which is more than enough for your camper. That said, as a disclaimer we do not have any way of knowing the exact scissor...
  view full answer...
• Distance Between the Mounting Holes of the Ram Scissor Stabilizer Jack # TJSC-24
  I am attaching a photo of the mounting locations on the Ram Scissor Stabilizer Jack # TJSC-24 that I believe you were referencing. They are from the edges of the mounting holes but I believe your mounting hole locations would match up just fine. Let me know if you were talking about a different set and I can see what those are as well. Attached is a review video for you to check out as well.
  view full answer...
• How Much Does the Ram Scissor Stabilizer Jack # TJSC-24 Weigh
  The Ram Scissor Stabilizer Jack # TJSC-24 has a shipping weight of 12 lbs. When you take away a few lbs for the shipping materials that leaves you with about 10 lbs just for the jack itself.
  view full answer...
• Nut / Socket Size Used to Raise and Lower the Ram Scissor Stabilizer Jack # TJSC-24
  The Ram Jack # TJSC-24 measures 3/4 inches. A 19 mm wrench or socket can also be used. The recommended manual crank handle for this unit is # TJSC-24-HD this has the proper size socket for use with these jacks. I have linked the above mentioned products to this page for your convenience.
  view full answer...
• Using Ram Scissor Stabilizing Jacks on Uneven Ground
  The foot of the Ram Scissor Stabilizer Jack # TJSC-24 should not be loosened to adjust for uneven ground. While it is true that the feet do not adjust with the terrain you do need to do your best to ensure that the feet are as solidly on the ground and as level as possible in order for them to give you the best performance to stabilize and level your trailer.
  view full answer...
• Does Ram Scissor Stabilizer Jack # TJSC-24 Have Height 18-3/4 inch or 23-3/4 inch
  I apologize for the confusion, but what's going with the Ram Scissor Stabilizer Jack # TJSC-24 is that it will move a total of 18-3/4 inches which gives it an overall height of 23-3/4 inches. So while the two numbers are confusing they are both "correct" in their own way.
  view full answer...
• Scissor Jacks for 1959 Canned Ham Camper Trailer
  The Scissor Jacks part # TJSC-24 that you referenced would work great on your 1959 Canned Ham camper. These are tall and have more than enough capacity which means they'd work really well to stabilize your camper.
  view full answer...
• Where Are the etrailer Scissor Stabilizer Jacks Made
  The majority if not all of the Scissor Stabilizer Jacks like part # TJSC-24 are going to be made overseas. That said, this is not a sign of poor quality because if you look at the reviews you will see a reflection of a quality well made product. If interested, we also have other options with more lift such as ones from Ultra-Fab part # UF48-979006, Lippert part # LC285325, and Stromberg Carlson part # JSC-24-IND.
  view full answer...
• Brainstorming Sidewind Trailer Jack for 2 Inch Receivers On Cargo Trailer Corners For Stabilization
  Interesting. We don't have that specifically, but there are a couple of routes you could go. Most trailers will use the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 # TJSC-24 for stability in the corners so you could mount a receiver shank to that and use # TJSC-24-HD as a sidewind crank. It sounds like you were picturing more of a trailer tongue style option, so you could use a jack like the Fulton Square, Fixed-Mount Marine Jack - Drop Leg - Sidewind - 30" Lift -...
  view full answer...
• Does the Ram Scissor Stabilizer Jack # TJSC-24 Come With Mounting Hardware
  The Ram Scissor Stabilizer Jack # TJSC-24 does not come with attachment hardware. I recommend going with the largest bolts that will fit, grade 5 or higher, if you will be bolting the jacks on. They can also be welded on, which will be the strongest option. Welding should be performed by a qualified professional.
  view full answer...
• Will Ram Scissor Stabilizer Jack # TJSC-24 Fit A Rockwood A213HW A-Frame Camper?
  For your Rockwood A213HW A-frame camper, the Ram Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 # TJSC-24 will fit and work well. This stabilizing jack will extend up to 23-3/4 inches and will collapse to 5 inches. From what I can find online for your trailer, it looks like you have 12 inches of clearance from the ground to your frame so this stabilizing jack will work very well for your application. The mounting flange is 10 inches by 3-1/4 so the location of your installation...
  view full answer...