Replacement Stabilizer Jacks for 2020 Rpod 195

Question

Question:

We pretty quickly and easily bent back two scissor stabilizer jacks on our rpod. We plan to replace either just the two or all four. Is there a better solution ... maybe even one that stores cranks up higher for better clearance? Thanks. You guys always offer the best advice.

asked by: Ann

0

Expert Reply:

I recommend to add Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2 # JSC-24 to the Rpod which will give you about 24" of height. When collapsed the jacks are 4" which is about 3/4" shorter than the other options to help with ground clearance. We do not carry a scissor stabilization jack that would store but that is a great idea.

To make the Rpod more stable I recommend to use the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers part # LC191025 which will attach the scissor jacks and then to the bottom of the trailer frame to help to stabilize the trailer. The JT's Stromg Arm kit will really help with excess chassis movement. They are great for eliminating the need to tip toe around when someone in the trailer is still sleeping.

expert reply by: Heather A

0

Answer 1

The JT's Strong Arm Jack Stabilizer Kit for Travel Trailers #LC191025 only comes with 6 sets because the a majority of the weight of the trailer is supported by the axles/wheels which are towards the end of the end of the trailer, so only one…

view full answer...

Answer 2

Hey Robert. Our highest capacity scissor jacks are going to be the etrailer Scissor Stabilizer Jacks. They come in a 4-pack item #e74RV or a 2-pack item #e96VV and have a 7,500 lbs capacity per jack. We do have ones rated for 10,000 lbs apiece. What…

view full answer...

Answer 3

Hey Steve, Yes The Big Truck Big Rv Scale #BTBRV004 is hydraulically operated to measure the tongue weight. No electronics or springs inside of it, overall a great scale. What kind of trailer are you towing?

view full answer...

Answer 4

Yes, the 921 bulb #VA0415-00 will work well for you. The 912 and 921 bulbs are interchangeable as they have the same T-5 wedge base. The 921 has a wattage of 16.8 and draws 1.4 amps. The 912 is 12 watts and draws 1 amp. So the 921 should burn…

view full answer...

Answer 5

These manual scissors jacks are for stabilization and not for leveling, so if you want to level out your Class C Winnebago Vita motorhome then you will need leveling blocks, the Ultra-Fab Leveling Blocks for Trailers and RVs #UF48-979051. Then for…

view full answer...

Answer 6

Since the king pin stabilizer is only a stabilizer and not actually bearing the full weight you won't actually need to match the pin weight of the trailer and could go with a lower rated (1200lb capacity) stabilizer. The difference between the…

view full answer...

Answer 7

The Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer #UF19-950500 referenced in your question has a support capacity of 5,000 pounds. This tripod will allow you to quickly and easily stabilize your unhitched fifth-wheel trailer. It features an…

view full answer...

Answer 8

For a pair of stabilizer jacks that would have more than enough capacity that would work well on your R-Pod I would recommend the Stromberg Carlson Trailer Scissor Jacks part #JSC-24. These have a 5k capacity per jack and would do a great job as long…

view full answer...

Answer 9

The stabilizer jacks aren't trailer specific, but the mounting hole spacing is pretty standard across the board. I'd recommend removing the damaged jack and comparing the mounting plate hole spacing to what's shown in the provided photos.…

view full answer...

Answer 10

The R-Pod 189 usually comes fitted with four corner-mounted scissor jacks that bolt to the frame. We have a number of such bolt-on stabilizer jacks that are shown on the linked page. Many of these are sold as pairs but we also have single jacks too,…

view full answer...

Replacement Stabilizer Jacks for 2020 Rpod 195

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching