How to Use Power Drill to Make Raising and Lower Scissor Jacks for Camper Quicker

Question

Question:

I was wondering if I can use a drill such as a impact drill to raise and lower the jacks quicker

asked by: Joe

0

Expert Reply:

Yes, you can use a drill to make raising and lowering the scissor jack set part # JSC-24 a bit quicker. You'll just need the drill adapter part # UF48-979005 too and you'd be set. This basically is a socket attached to a power drill shank. The size socket that comes with this is 3/4 inch.

See review video I attached for this as well.

expert reply by: Jameson C

0

Answer 1

The Curt Trailer Hitch Receiver #13333 referenced in your question is confirmed to fit your 2004 Dodge Ram 1500 as long as you replace what you have with the standard OEM bumper. The Curt hitch is going to attach to the truck's factory bumper…

view full answer...

Answer 2

Determining the correct weight distribution system is dependent on the total tongue weight of your trailer. Ideally you want your total tongue weight to be in the middle of the range of the weight distribution system you choose. To measure the total…

view full answer...

Answer 3

The best way to determine which weight distribution system with sway control to use on a setup is to base it on the tongue weight of the setup. You will also need to consider any weight that is behind the rear axle of the tow vehicle as tongue weight…

view full answer...

Answer 4

Because it's oddly shaped, it's difficult to provide an overall length, as it will depend on where you measure from and your dimension includes the factory mirror width as well. However, when installed, the #LO34FR Longview Slip On Towing…

view full answer...

Answer 5

I find the K-Source Snap & Zap Custom Towing Mirrors #KS80730 are the best solution for your 2024 Ram 1500. These mirrors are custom fit so they easily snap in place over your factory mirrors. Since there are no hardware or wedges to lose or…

view full answer...

Answer 6

The K-Source Snap & Zap Custom Towing Mirrors #KS80730 are our best towing mirrors for your 2024 Ram 1500. These are custom fit to snap onto the non-extending factory mirrors. They do not use additional hardware or wedges for a snug fit which can…

view full answer...

Answer 7

Hey Steve, Yes The Big Truck Big Rv Scale #BTBRV004 is hydraulically operated to measure the tongue weight. No electronics or springs inside of it, overall a great scale. What kind of trailer are you towing?

view full answer...

Answer 8

Hey Ellie, the length of the etrailer scissor jack part #e56VV when folded down is 24-7/8 inches.

view full answer...

Answer 9

Yes, the 921 bulb #VA0415-00 will work well for you. The 912 and 921 bulbs are interchangeable as they have the same T-5 wedge base. The 921 has a wattage of 16.8 and draws 1.4 amps. The 912 is 12 watts and draws 1 amp. So the 921 should burn…

view full answer...

Answer 10

We definitely have options for that, Joe! The Lippert Ground Control 3.0 you asked this question from is actually what I would recommend. If is featured in a bunch of OEM set ups and is by far the best one on the market. It can handle campers with a…

view full answer...

Answer 11

The Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer #UF19-950500 referenced in your question has a support capacity of 5,000 pounds. This tripod will allow you to quickly and easily stabilize your unhitched fifth-wheel trailer. It features an…

view full answer...

Answer 12

Since the king pin stabilizer is only a stabilizer and not actually bearing the full weight you won't actually need to match the pin weight of the trailer and could go with a lower rated (1200lb capacity) stabilizer. The difference between the…

view full answer...

How to Use Power Drill to Make Raising and Lower Scissor Jacks for Camper Quicker

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching