See what our Experts say about this etrailer Straight Tongue Trailer Coupler

• Replacement For Shelby 5135 Coupler With 3 Channel
  I recommend etrailer.com Channel Tongue Coupler part # CT-5003-Z to replace the Shelby 5135 coupler. The etrailer.com coupler has a channel width of 3" and takes a 2" ball. It also has 3" from center of bolt hole to center of bolt hole which are the dimensions of your Shelby coupler.
  view full answer...
  
• What Do I Need to Change My Hydraulic Drum Brakes to Electric Drum Brakes on My Boat Trailer?
  Hello Greg, Yes, you can use the same drum for the electric brakes that you used with your hydraulic brakes. Based on the measurements you provided, it looks like you have a #84 spindle, which typically means you're working with a 3,500 lb axle. Here’s what you’ll need for the conversion: You will need: - etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K # AKEBRK-35-SA - Deka Jacketed 2 Wire, 10 Gauge, Brake Wire # 10-2-1 sold by the foot so...
  view full answer...
• Parts Needed to Add Electric Brakes to ShoreLand'r Boat Trailer
  Hey Ryan! We don't have a way to identify your axle using the VIN so you will have to check and see what axle you have before we can find the right parts. I would start by checking the axle tag. It may have the capacity listed or, at least a serial number the axle manufacturer could use to identify it. If not, you will need to check and see what bearings you have. The part numbers may be stamped in the side or you can measure the inner diameter with a digital caliper # PTW80157. If you...
  view full answer...
• Availability Of Latch Repair Kit For Fulton 2" Ball Coupler
  Hey Mike, thanks for reaching out. Sounds like you are needing a latch repair kit for a Fulton coupler. Unfortunately, we no longer offer any replacement parts or repair kits for these. If your coupler is in need of a new latch, your best option will be to replace the coupler entirely. The Channel Tongue Trailer Coupler # CT-5003-Z is a great option for replacing a standard 2" ball coupler. It will fit a standard 3" tongue and has a standard 3" bolt hole spacing. This is what I recommend...
  view full answer...
• How To Lock Out Older Surge Coupler After Converting To Electric Brakes
  Hey David. Is there a brand or part number stamped anywhere on that older actuator? If so, we can narrow down how to lock it out manually as most have that feature. That said, the best and safest option is to just replace the old one with a new standard non-surge actuator since you already converted the brakes to electric. You'll need to cut off the old one and weld a new one on. You'll want to measure how wide that one is, or in other words, how wide the channel is where the coupler...
  view full answer...
• Is There a Repair Kit for Fulton Straight Tongue Coupler
  Hey Ben, that looks like a Fulton coupler but we do not have any repair kits that fit it. However, we do have a replacement coupler with the part # F343000301.
  view full answer...
• Replacement Cost Efficient Coupler for Shelby 5138
  A replacement for your Shelby 5138 is the Fulton Fas-Lok Coupler, 2" Ball, 3" Channel - 3,500 lbs # F223000301. This is a great quality coupler that is cost effective as you referenced. I've attached a review video of this product to assist. If you are wanting a stronger coupler at a great cost, I recommend the Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 5,000 lbs # CT-5003-Z. This is a quality product at a very low cost that I highly recommend.
  view full answer...
  
• Replacement Coupler, Bearings and Hubs for a Detail K2 Utility Trailer
  Hey Steve, for your Detail K2 trailer you can use the Channel Tongue Trailer Coupler # CT-3002-Z for a replacement coupler. This coupler is rated for up to 3,500 lbs, has a Zinc finish, and has a bolt on install. For a bearing kit, it looks like it uses the Bearing Kit, L44649 Inner/Outer Bearings # BK1-150 and for hubs you'll wan to use the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles # 8-259-5UC1. Please feel free to let me know if there is anything else I can help you with!
  view full answer...
• Parts Needed To Convert Trailer From Surge Brakes To Electric Brakes
  Hello Allen, thanks for reaching out. We do have the parts you will need to convert your trailer from surge to electric brakes, but there is no way to look up your trailer online to know exactly what parts you will need. The main thing we need to nail down is which brake assemblies and hubs you will need. If you can provide me with the casting number from your hubs, I should be able to use that to look up the info I need. Basically I need to know the weight capacity of your axle, your...
  view full answer...
• Tips for Difficult to Latch and Unlatch Trailer Coupler
  Hey Ben, so this is pretty common with older couplers that get a bit of dirt and corrosion in them over time. If you haven't tried already I would really go to town soaking the coupler latch assembly with as much WD40 that you can to see if you can get it to free up. Normally that works pretty well. A latch repair kit could work well too assuming we have the correct kit for your coupler. But I would need to see pictures and know the brand of what you have as well. Otherwise you could...
  view full answer...
• Is Welding or Bolting on a Trailer Coupler Easier
  Hey Tim, bolt on couplers can definitely be easier to install but that's only if you can find something that's an exact replacement and uses same bolt pattern. Which due to the age of your trailer I would bet that we don't have something that would bolt right up without having to redrill holes or make some changes etc. So welding a coupler on is going to be a lot easier. Is the trailer an a-frame trailer or a pole tongue? What ball size would you like the coupler to be designed for.
  view full answer...
• Replacement Coupler for Trailer Switching from Surge to Electric Brakes
  The Channel Tongue Trailer Coupler # CT-5003-Z has a 3" wide channel designed to fit a 3" wide tongue. If you're saying it is 3-1/2" wide this wouldn't fit either. To save yourself some money I would just drill into the old coupler and run bolts through it to permanently lock it out. This is a common solution when making this conversion, I apologize for not throwing that into my original answer. You can return it, and I linked the full policy down below under "Featured Help Information."...
  view full answer...
• Can The 3 Hole Demco Coupler Be Used On a 3" Channel Tongue With Only 2 Mounting Holes?
  Yes, you would be able to drill out the 3rd hole for the Demco Coupler # 12564 and use it on your 3" wide channel. It sounds like you have a coupler like our etrailer # CT-5003-Z which only used the 2 mounting holes due to the light weight of the trailer. Our coupler is only rated for trailers up to 5,000lbs while the Demco is rated up to 10,000lbs.
  view full answer...
• How to Determine the Correct Coupler for a 1975/6 21' Kit Companion Travel Trailer
  Hey Thomas, I've attached an FAQ on how you can identify your coupler but basically you just need to take note of its type (A-frame, Straight tongue, etc.), the trailer side connection, how it installs and the capacity. So from what I can see, your 21’ Kit Companion travel trailer uses an A-frame style coupler with a standard hitch ball setup. I did also check the capacity and it looks like your trailer has a GVWR of 5,000 lbs, so something like the Demco A-Frame Trailer Coupler w/ Jack...
  view full answer...
• Repair Kit Availability for Shelby 5135 2 inch Coupler
  I do have a solution for you but unfortunately, the CA-5100-RK isn't compatible with your Shelby 5135 coupler. While there isn't a repair kit available for your coupler, replacing the entire unit is just as cost effective. For a very similar replacement, I recommend the etrailer.com Channel Tongue Trailer Coupler # CT-5003-Z. This takes a 2 inch ball, is rated for 5,000 lbs and fits a 3 inch wide channel just like your Shelby coupler. I've attached a photo showing the mounting hole distance...
  view full answer...
  
• Inner Channel Dimensions Of Channel Tongue Trailer Coupler # CT-5003-Z
  The inner dimensions of the Channel Tongue Trailer Coupler # CT-5003-Z are 5" from the bend to the rear of the coupler, 3-1/6" wide and 2-1/8" tall. I have created a diagram with these measurements below.
  view full answer...
  
• Is There a Replacement Latch for the Shelby 5135 Trailer Coupler
  I do have an option for you but Shelby is no longer in business so replacement parts are not on the table. That said, we do have a full replacement option for you in the Channel Tongue Trailer Coupler part # CT-5003-Z which is a direct fit so there's no drilling required.
  view full answer...
• Bolt Hole Distance on etrailer.com Trailer Coupler
  The mounting holes of the etrailer.com trailer coupler are spaced 3-1/16 inches apart on center. The holes themselves are a 1/2 inch in diameter.
  view full answer...
  
• Mounting Hole Distance to Bottom of Channel for etrailer.com Channel Tongue Trailer Coupler
  Yes, the mounting holes for the Channel Tongue Trailer Coupler # CT-5003-Z measure 1" from the center down to the bottom of the channel.
  view full answer...
  
• Replacement Coupler Solution for Shelby 5135
  Since Shelby couplers aren't available you would need to buy an all new coupler like with the part # CT-5003-Z that you mentioned. This fits 3 inch channel like what you have and also is designed for the same 2 inch hitch ball size.
  view full answer...
• Replacement Channel Tongue Coupler for a Valley/Shelby 5135 2" Coupler
  Unfortunately, replacement parts for the Valley/Shelby 5135 2" coupler are no longer available. My only option would be to replace it with the Channel Tongue Trailer Coupler item # CT-5003-Z. The Channel Tongue Coupler item # CT-5003-Z also fits a 3" channel and works with a 2" ball. It has mounting bolts 3" on center but can also be welded on. What kind of trailer do you have? You can add this information, along with any other questions you have, where it says Add Comment.
  view full answer...
• Bolt Size Recommended For Channel Style Tongue Trailer Coupler Installation
  To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On # CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video to help as you plan this installation.
  view full answer...
• Recommended Repair Kit for Shelby 5136 Coupler
  I have a solution for you, but there is not a repair kit available for the Shelby 5136 coupler. However you can replace the coupler, and I recommend using the Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 5,000 lbs # CT-5003-Z to do so. This will bolt on to a 3 inch channel tongue and fits a 2 inch hitch ball, so it will fit in place of your older Shelby 5136 coupler. I've also linked a short review video of this coupler for you to check out, but replacing...
  view full answer...
• Locks For a Master Tow Car Dolly With 2" Ball Demco Coupler
  Based on information I could find on the Master Tow car dollies I see they use a 2" coupler like our # CT-5003-Z. For this I recommend getting the Master Lock Set # 3794DAT which will provide you with a coupler lock, storage lock and receiver lock all keyed alike. The InfiniteRule Lock # IR66FR you found is a great lock but is for their EZ Latch Coupler # 12564 if this is what you have.
  view full answer...

Do you have a question about this Straight Tongue Trailer Coupler?