In-stock alternatives that can ship today
Corrosion-resistant, straight-tongue trailer coupler features a trigger-style latching mechanism that securely locks in place around your 2" hitch ball.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're taking a look at the Titan Zinc Plated Lever Lock Coupler.Now this unit mounts to your trailer and allows you to connect your trailer to your tow vehicle.The lever lock coupling mechanism ensures easy, secure connection to a two inch hitch ball.So basically when you're ready to use it, what you'll need to do is you'll need to remove the included pin, it's tethered on there so you don't misplace it or lose it. That can be replaced with a locking pin if desired. But then you slide this ball, it's like a half ball right here, you put your finger on the finger indention area, slide it over and then lift up the lever.Now that fully opens the coupler to receive a two inch ball. Once the ball engages, it will push back down that lever, it will click into place. That audible click lets you know that it's fully engaged and you're ready to reinstall your pin and get on the road.Now the unit itself is made from a durable steel construction with zinc plating to resist rust and corrosion, it's a bolt on installation, two mount holes on each side of the unit. Parts are made in the U.S.A.
Again, it's designed for a two inch ball.The space right here, inside edge to inside edge measures about three inches so that lets us know this is for a three inch wide channel tongue. The bolt holes on the unit, these are separated apart from one another on center by three inches and they have a half inch diameter. Mounting hardware not included.All your capacities are engraved right here on the top. So, this unit features a 5,000 pound gross load capacity, 750 pound tongue weight capacity.Then when it comes to the overall length of the unit measuring from the very front to the very back you can see it measures about 11 inches long.That's going to do it for today's look at the Titan Zinc Plated Lever Lock Coupler.
Average Customer Rating: 4.7 out of 5 stars (20 Customer Reviews)
Corrosion-resistant, straight-tongue trailer coupler features a trigger-style latching mechanism that securely locks in place around your 2" hitch ball.
Used this coupler to replace the aging and obsolete folding surge coupler on my dated and neglected Nautique Ramlin trailer. Deleted the surge system and this bolted up perfectly. Super easy and smooth operation for locking onto the tow ball.
Creates a locking challenge. Needs a special lock. The open slide is not smooth and sometimes hard to work. The coupling is a challenge on any slope. Sometimes we need to drag the trailer to a flatter spot to get it to engage.
Exactly the part it says it is. Working well for me.
PRO: Arrived well packaged and undamaged. Good tight fit on the 2" ball.
CON: I was replacing an older Titan coupler. The new coupler's bolt holes did not match the old coupler's hole pattern - off by 1/32" to 1/8", so the bolts will not fit thru the matching holes in the trailer. Rather than a 15 minute replacement, I now have to drill out the trailer bolt holes to make the new coupler fit, meaning that I will not have the close tolerance bolt-to-hole fit. This looser fit can ultimately cause wear on the bolts. I now plan to put in a bolt replacement maintenance exam/replacement reminder every year (to be safe).
Awesome coupler. Solid contact with the ball, super low profile, easy to use latch , this is exactly what I wanted as I run a bike rack above the coupler, plenty of clearance for unhitching the trailer without removing the rack.
I have two different vehicles with two different hitch ball diameters. I purchased this coupler to allow me hassle free use of either vehicle with the trailer equipped with the coupler.
The couple is a very clever design and should allow me the flexibility that I was looking for. I haven't had a chance to use it yet, but it looks great and I am considering putting them on all of my smaller trailers.
This coupler worked out great for my trailer tongue. I like the type of mechanism that is used to connect to the trailer ball. The old trailer coupler has been very problematic when I tried to make a connection.
Only place I'll shop. Outstanding service and delivery.
Works perfectly. Bolted on easily.
Product is exactly what I ordered and it came within two days. Will definitely buy from etrailer again.
Product as advertised!
What’s not to like.
Fast shipping
Do you have a question about this Straight Tongue Trailer Coupler?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.