Bolt Size Recommended For Channel Style Tongue Trailer Coupler Installation

Question

Question:

What size bolt should be used to bolt this to the trailer?

asked by: Andy

0

Expert Reply:

To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On # CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video to help as you plan this installation.

expert reply by: Jason S

0

Answer 1

The "D" designation that you see on the ST225/75-15 tires for your travel trailer indicate a bias ply tire, as opposed to the radial ply tires on your cargo trailer. The primary difference between bias and radial tires is how they're…

view full answer...

Answer 2

I do have an option for you but latch repair kits are coupler specific and there are very few out there. Furthermore, the Lippert 2" Latch Coupler Repair Kit 678750 is no longer available and I know this isn't what you want to hear but the…

view full answer...

Answer 3

No, the only cameras that we currently have confirmed to work with a GMC Infotainment system are the cameras made by GM. You'll also need to check exactly which brand your 2022 Alliance Paradigm 5th wheel is prewired for. If you have a…

view full answer...

Answer 4

It looks like a Hayes Brake magnet part number 73400. We do not carry this part but I did a quick internet search and was able to find a couple places that sell them. From the research I did it looks like this is an older style of brake magnet used…

view full answer...

Answer 5

Hey M, thanks for reaching out! Since you aren't seeing wires like what we show in the Redarc Tow-Pro Elite Brake Controller #RED44FR install video on a 2019 Ford Ranger, are you seeing a plug anywhere? The wiring is tucked up pretty far into the…

view full answer...

Answer 6

Hey Del, thanks for reaching out. I don't recall ever seeing that before, a coupler with a bolt going through the top like that. I suppose it doesn't hurt, but it definitely isn't necessary. Typically, two bolts, or at the most three…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey John, thanks for reaching out. You will want to use some 1/2" grade 5 bolts and locknuts for mounting the Demco Channel Tongue Trailer Coupler #DM15945. Since the current coupler uses only 2 bolts, you will be fine to use two bolts with the…

view full answer...

Answer 9

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 10

The etrailer Trailer Coupler #CTA-400 uses the Replacement Mounting Bolt with Nut for Adjustable Channel Couplers #MBT58500-LN58. This is a 5/8" grade 8 bolt. I have attached a diagram below which shows the full dimensions.

view full answer...

Answer 11

The Grade 8 mounting bolts that come with the Trailer Coupler #CTA-280 have a 5/8" diameter and an overall length of 5-1/8" including the head. Without the head of the bolts they measured 4-13/16".

view full answer...

Answer 12

The Kenda 5.30-12 Bias Trailer Tire with 12" White Wheel #AM30859 will fit your Harbor Freight trailer as long as it uses the same 5 on 4-1/2" bolt pattern. The larger pilot hole diameter is not a problem since the wheels are lug centric…

view full answer...

Bolt Size Recommended For Channel Style Tongue Trailer Coupler Installation

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching