Inner Channel Dimensions Of Channel Tongue Trailer Coupler # CT-5003-Z

Question

Question:

What are the inside dimensions of the channel on this coupler? Thanks.

asked by: Brian W

0

Expert Reply:

The inner dimensions of the Channel Tongue Trailer Coupler # CT-5003-Z are 5" from the bend to the rear of the coupler, 3-1/6" wide and 2-1/8" tall. I have created a diagram with these measurements below.

expert reply by: Bud M

0

Inner Channel Dimensions Of Channel Tongue Trailer Coupler # CT-5003-Z
(click to enlarge)

Answer 1

To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On #CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video to help as you plan this installation.

view full answer...

Answer 2

The mounting holes of the etrailer.com trailer coupler are spaced 3-1/16 inches apart on center. The holes themselves are a 1/2 inch in diameter.

view full answer...

Answer 3

Yes, the mounting holes for the Channel Tongue Trailer Coupler #CT-5003-Z measure 1" from the center down to the bottom of the channel.

view full answer...

Answer 4

I had the Demco Channel Tongue Trailer Coupler - Zinc - 2" Ball #DM12717 measured and included a diagram with the spacing you are looking for, and a little more if needed. With that being said, from the center of the first bolt hole to the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Inner Channel Dimensions Of Channel Tongue Trailer Coupler # CT-5003-Z

Product Page this Question was Asked From

Continue Researching