Is There a Repair Kit for Fulton Straight Tongue Coupler
Updated 08/15/2024 | Published 08/12/2024
Products Featured in This Question
Question:
Hi. This is in response to a thread already in progress. Link below. When I originally posted the question there wasn’t a spot for picture upload. Anyways, heres a pic of the top and bottom of the coupler. Notice theres no locking mechanism on the adjusting nut. The trailer is a Load Rite 14700LRT https://www.etrailer.com/question-771637.html?fb=yes
asked by: Ben P
(click to enlarge)
Expert Reply:
Hey Ben, that looks like a Fulton coupler but we do not have any repair kits that fit it. However, we do have a replacement coupler with the part # F343000301.
Product Page this Question was Asked From
Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 5,000 lbs
- Straight Tongue Trailer Coupler
- Standard Coupler
- 2 Inch Ball Coupler
- Bolt-On
- 5000 lbs GTW
- 3 Inch Channel
- Trigger Latch
- 2-Bolt
- Marine Grade
- etrailer
more information >
Continue Researching
- Shop: Fulton Fas-Lok Coupler, 1-7/8" Ball, 2" Channel - 2,000 lbs
- Q&A: Tips for Difficult to Latch and Unlatch Trailer Coupler
- Search Results: hitch pins and clips
- Search Results: ct~2001~z
- Q&A: Troubleshooting Coupler that is Difficult to Latch onto Hitch Ball
- Q&A: Replacement Parts For Fulton Straight channel Coupler For 1-7/8 Inch Trailer Ball
- Q&A: Latch Repair Kit for a 1-7/8 Inch Trailer Coupler
- Q&A: Do All Trailer Coupler Latch Repair Kits Fit All Couplers
- Search Results: coupler pins
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 1-7/8" Ball - Bolt On - 2,000 lbs
- Shop: Replacement Pin and Clip with Lanyard for Curt QuickPin No-Latch Trailer Coupler
- Shop: Replacement Pin with Chain Lanyard for Bulldog Flat-Mount, Wedge-Latch Trailer Couplers - Qty 1
- Shop: Curt Coupler Safety Pin, 1/4"
- Shop: Replacement Coupler Pin Kit for Dexter Brake Actuators
- Shop: Coupler Pin w/ Chain- 1/4" Diameter x 1-3/8" Long
- Video: Breaking Down the Fulton Fas-Lok Coupler, 1-7/8" Ball, 2" Channel
- Video: Channel Tongue Trailer Coupler Review
- Q&A: Wiring Instructions for the Tradesman Vaquero Hydraulic A-Frame Trailer Jack
- Q&A: Replacement For Shelby 5135 Coupler With 3 Channel
- Article: Trailer Wiring Diagrams
- Article: Trailer Lighting Requirements
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Holiday 2025 | Best Gifts for Towers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
Ben
8/15/2024
Hi. Thanks for looking. It's a 2" channel (assume that means the bar width underneath), not 3". If I was to replace, I was thinking either part #CT-2001-Z, or E112000340 (which is a Fulton). Would either of those work? Did you see the picture of the nut underneath which I had sent in? Does it look 'right' not having a locking mechanism around the nut?