Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White
(369 reviews)
Price: $414.96
In Stock
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White
Item # BD500200
Retail:$523.54
Our Price: $414.96
You Save: $108.58
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (369)
- Q & A (0)
- Photos
Bulldog Camper Jacks - BD500200
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jack
- Electric Jack
- 1 Jack
- 22 Inch Lift
- Bulldog
- Bolt-On
This electric A-frame jack offers 22" of total lift. The drop leg has a spring-loaded pull pin for quick release. 3 LED lights allow easy setup at night. Built-in level included. Extends 6" in 28.5 seconds with 1,000 lbs of tongue weight.
Features:
- Tongue jack positions quickly and easily with integrated drop leg
- Powered drive provides quiet operation and efficient use of electrical power
- No more hand cranking
- Spring-loaded pull pin quickly releases the drop leg into position
- Built-in level has springs for simple, accurate leveling
- 3 LED lights make it easy to set up at night
- Side-mounted spot lights are angled rearward to illuminate weight distribution brackets
- 4" - 6" Overlap of tubes at full extension provides additional support for side loading
- Easy-to-access on/off and retract/extend toggle switches make for simple operation
- Corrosion-resistant, sealed, maintenance-free surfaces
- Easily accessible emergency manual override in case of power loss
- White housing with sleek design protects motor
Specs:
- Bracket height:
- 9-3/4" Retracted
- 31-3/4" Extended
- Total lift: 22"
- Screw travel: 14"
- Drop leg travel: 8"
- Travel speed (w/ 1,000-lb tongue weight):
- Extends 6" in 28.5 seconds
- Retracts 6" in 25.4 seconds
- Inner tube diameter: 2"
- Outer tube diameter: 2-1/4"
- Lift capacity: 4,000 lbs
- 5-Year limited warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
500200 Bulldog A-Frame Jack with Powered Drive, 22" Lift, 4,000 lbs
Replaces Bulldog BD500185
Installation Details
California residents: click here
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- etrailer mistake
- Arrived Damaged
Customer Reviews
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White - BD500200
Average Customer Rating: 4.8 out of 5 stars (369 Customer Reviews)
This electric A-frame jack offers 22" of total lift. The drop leg has a spring-loaded pull pin for quick release. 3 LED lights allow easy setup at night. Built-in level included. Extends 6" in 28.5 seconds with 1,000 lbs of tongue weight.by: David08/26/2023
I have had problems with inadequate clearance between the lift gate of my Ford F150 and tongue jack motors on prior travel trailers. Some lifts allow the motor to be rotated sideways, but the bulky Lippert that came with my new Winnebago TT didn't. The Bulldog is made to be mounted either forward or sideways and has a particularly narrow body. Installation was a snap, and I drilled holes to rotate the bubble level to be aligned fore and aft. I opted not to use the clever Plunger Pin Kit which is mounted to be pulled from the side because when the unit is mounted sideways, the pin with its fairly stiff spring would have to be deployed and operated either fore or aft beneath the hitch or the tongue assembly. So I am using the original lynchpin assembly for the drop leg.
Now I have plenty of clearance between the Bulldog lift, the F150 drop gate and the propane tanks and cover.
by: Denis04/07/2018
I am extremely pleased with everything about the purchase. The jack was described very accurately, I had a question before delivery about the fit on my R-Pod which was answered very thoroughly and the jack arrived on time. The installation was quick and easy. The jack operates very smoothly. The features of the LEDs, the quick pull pin for the drop foot and the bubble level are perfect for my application.
by: Dave12/19/2023
The Bulldog Jack has been great!
by: Shorty S.01/25/2017
I installed this electric jack on my 3-horse bumper pull trailer. I'm using power straight from the truck's RV 7 wire hook-up. I, along with my family are so glad I installed this every time we hook up to the trailer. The adjustable leg is also an added benefit. I also purchased the termination box and this allowed for a superior installation by putting all the terminations in a water proof box versus open wire joints. Thanks etrailer for your support and your quality products.
by: RightStuffer10/23/2017
I have a 2007 14' V-noise extra wide and tall trailer, and the jack was needing to be replaced. I figured it was a good time to think about a powered lift option. After spending several days doing research, I determined that the Bulldog Powered Drive Trailer Jack, was the best product to meet my needs. etrailer has this product for the best price online, and offered free shipping, so for basically $100 more than a high quality none powered replacement jack, It was a no-brainer.
My wife and I installed the unit on my trailer that was still on my tow vehicle in less than 45 minutes, and everything we needed minus a weather proof inline connector was included. It was so easy to install, and looked so good after installation.
Because of the size and weight of my trailer, hooking and unhooking my trailer used to be a real chore for me, since I am older and have back problems. Then it was time for the true test, dropping the trailer for the first time.
WOW! The spring loaded pin for the drop leg made it so easy! No more need for the several wood blocks we needed to lug around. Also it was now dark, so I turned on the lights. What a difference! The video does not do the lights justice. They clearly illuminate the rear of the tow vehicle, and front of the A-frame of the trailer.
Then, by simply pushing the weather proof button, a chore I used to dread, that left me sore and sweaty, was now effortless! Quiet, smooth operation, and built in stops for extra protection.
Very solid high quality construction, with all the features you need and want. The all weather design, powder coated metal parts make it easy to understand the reason why the manufacturer offer a 5-year warranty.
I am only left with one question...why did I wait so long to buy this great product at the lowest price from Etrailer?
by: HB 05/31/2018
I purchase this item to replace a 12 year old power jack. I’m spoiled and I’ll never go back to a manual jack. The jack feels and looks like a high-quality unit. All hardware was individual packaged. Installation went smoothly following the excellent directions.
I’ve run the jack up and down a couple of times and it functions smoothly and quietly. The drop-leg is an excellent design.
I look forward to many years of service from this jack.
Hb
5/31/2019
I have found a flaw in the jack. The metal rod used to release the foot is made from pretty junky metal. It got hung-up in my chains while I was lowering the jack and bent. The deflection was pretty minimal - I caught it very quickly - yet when I bent the long leg of the rod back, it broke off. For the price, I’m not impressed with this aspect of the jack. It has rendered the [] leg useless as I had to secure it in place so it didn’t fall out.
by: Steven 09/12/2022
The trailer tongue jack arrived undamaged and fits perfectly.
by: Jeffrey 08/23/2021
The Bulldog Powered Trailer Jack was a perfect fit for my Jayco White Hawk travel trailer. Installation was easy and the switches are easy to operate and are clearly marked. The customer service reps were awesome!
by: Michael07/04/2019
I bought an electric trailer jack. The price was fair, shipping was fast, and item was exactly as described.
Great service!
by: Bonnie G06/03/2020
I love my trailer jack. I was so tired of cranking and this is so easy. Just what I wanted!
by: Jeffrey 08/21/2021
Easy to install, works well. Used it to replace another jack that died after 5 years. It would be good if they included the electric hook up instructions with it. If I didn’t have the earlier jack connections I would have had a much more difficult time installing.
by: John 04/23/2021
Quick easy installation, all hardware provided, lights are just enough to see what your doing, only reason it's not 5 stars is because I've used it long enough to test. But it will be used daily, so testing won't take long, oh by the way shipping was 10 stars, haven't had a package arrive like it was supposed to in long time. Thanks everyone involved etrailer!
by: Trev J01/07/2018
Shipped on time, easy to install, great product and service, very happy.
Trevor J.
1/8/2019
Very good
by: William 07/24/2020
Easy installation and works great
by: Nathan.08/02/2020
It has been perfect. It gets used daily and never misses a beet.
by: James Barnes04/04/2017
Was used for our camper. Haven't used it at this time,but pretty certain it will be the best product ever purchased.
by: Alonzo03/12/2021
Alonzo
3/13/2022
I love it Great product
by: Olen 02/02/2022
great product the package was in bad shape when delivered by UPS hope everything is there.
by: Christopher 06/30/2023
by: Jon 12/22/2023
by: Jim06/28/2021
by: Bob 06/03/2023
by: Jean-Paul03/18/2021
by: David 06/29/2021
by: Mario 05/27/2021
25
368
Show More Reviews
See what our Experts say about this Bulldog Camper Jacks
- How to Wire the Bulldog Powered-Drive Trailer Jack # BD500200 on a Trailer with No BatteryThe Bulldog Powered-Drive Trailer Jack, item # BD500200, only has one wire, the power wire. This jack attaches to ground through the mounting hardware and the trailer frame. When wiring the jack to your 7-Way trailer connector you will need to make sure that the ground wire from the 7-Way trailer connector is attached to the trailer frame to provide ground. You will then attach the power wire to the 12 volt accessory circuit inside the 7-Way connector or splice into the wire the is attached...
view full answer...
- Dimensions for Installation of a Bulldog Electric Powered Trailer Jack with Propane Tanks on TongueThe distance from the top of the mounting plate to the bottom of the housing on the Bulldog Powered-Drive Trailer Jack, # BD500200, is 13 inches.
view full answer... - Can the Bulldog Powered-Drive Trailer Jack # BD500185 be Powered by 7-Way 12 V CircuitThe Bulldog Powered-Drive Trailer Jack, item # BD500200, only has one wire, the power wire. This jack attaches to ground through the mounting hardware and the trailer frame. When wiring the jack to your 7-Way trailer connector you will need to make sure that the ground wire from the 7-Way trailer connector is attached to the trailer frame to provide ground. You will then attach the power wire to the 12 volt accessory circuit inside the 7-Way connector or splice into the wire the is attached...
view full answer... - How to Prevent a Bulldog Powered 4,000 lb Jack from Damaging Gears Due to Over-ExtensionI spoke with my contact at Bulldog and he said they do not offer replacement parts to rebuild the gear box for the Bulldog Powered-Drive Trailer Jack, # BD500200. Typically the gears get damaged due to over extension or retraction. Before installing a new jack, power it up and extend it all the way with no load, back it up a bit and mark the leg. Do the same for the retraction. This way you will have visual marks of when to stop extension or retraction.
view full answer... - Replacement Powered A-Frame Trailer Jack for a 2005 Jayco Eagle Travel TrailerThere are a few things to consider when replacing a jack on a trailer. If you are replacing an A-frame jack, the mounting whole pattern is pretty much standard (3 inches apart on center). However, the shape of the mounting bracket could be round or more tri-angular. You also need to consider the tongue weight of the trailer and the amount of lift you need plus any clearances that may interfere with the jack. The best thing to do would be to get the measurements and capacities of your...
view full answer... - Wiring Options for Installation of a Bulldog Powered-Drive Trailer Jack # 500185Ideally you would wire the Bulldog Powered-Drive Trailer Jack, part # BD500200, to a separate battery. Normally trailers with powered jacks have an auxiliary battery that is used to power accessories. If there is not a separate battery on your trailer, you could power the jack from the 12 volt power source in your 7-pin trailer connector.. Here is how you would wire it to your 7-pin connector: On the 7-pin connector that is on your tow vehicle there should be a red or black wire that...
view full answer... - How To Maintain Charge In Trailer Battery That Will Run A Powered Trailer Jack On A Pace TrailerYou will want to use a standard 12 volt deep cycle trailer battery to operate the Bulldog Powered-Drive Trailer Jack, part # BD500200. You will NOT want to use a trailer breakaway battery. The breakaway battery is not designed to power other trailer accessories or lighting, it is just designed to operate the breakaway system. To keep the trailer battery charged you will need to run a 10 gauge power wire like the, part # 10-1-1, from the 12 volt power pin (# 4 terminal at 11:00 position)...
view full answer... - What is Quietest Electric A-Frame Trailer JackWe've found that the Bulldog trailer jacks like the part # # BD500199 (Black) or # BD500200 (White) are the quietest so either of these would be your best option.
view full answer... - How to Manual Raise and Lower a Bulldog Powered A-Frame Trailer JackIt depends on which Bulldog powered A-frame trailer jack you have. For example, # BD500200. has a cap on top and you can use a socket wrench and socket to manually crank the jack up and down. Jacks # BD500187 and # BD500188 come with a handle. But both of these have a cap on top that you will remove to access the manual override.
view full answer... - Recommended Heavier Duty Upgrade For FIC 3500 Electric A-Frame Trailer JackElectric A-frame trailer jacks often have the same bolt pattern, yes. Just keep in mind that a higher-capacity jack doesn't necessarily mean more speed, it's all about the jack itself. For example, the 3,500 lb Ultra-Fab Electric A-Frame Jack # UF38-944017 extends 6" in 25.3 seconds (with 1,000 lbs of tongue weight), while the 4,000 lb Bulldog Trailer Jack # BD500200 extends 6" in 28.5 seconds (with 1,000 lbs of tongue weight). That said, since you mentioned wanting a heavier-duty jack,...
view full answer... - Replacement Pull Pin For Bulldog Powered Drive Trailer jack BD500200It sounds like you are looking for the Replacement Spring Loaded Pull Pin # BD500388 for your Bulldog Powered Drive Trailer Jack # BD500200. If this is not what you are looking for just let me know. I included a video for both of the parts mentioned for you to take a look at.
view full answer... - Recommended Electric Tongue Jack For 2012 Dutchman Coleman 289 RLThe Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 4,000 lbs - White # BD500200 has the standard mounting flange and is probably closest to the jack you currently have. The drop leg will allow this jack less travel to reach desired height. You could also look at the Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black Item # JET-5000 which has a capacity of 5,000 pounds. Going higher with capacity will help the jack to last...
view full answer... - How Does Bulldog Powered A-Frame Jack Raise and Lower ManuallyYour Bulldog powered A-frame jack part # BD500200 would have come with a manual override lever like the part # BD500203 which you could use to manually raise and lower the jack as needed. If you check out the 5:36 mark of the review video I attached for this you'll see how the manual crank is used once removing the cap on the top of the jack.
view full answer... - Bulldog Powered-Drive Trailer Jack # BD500185 Recommendation for a 26 ft Travel TrailerAs long as your 26 foot travel trailer has an a-frame style trailer tongue and has tongue weight less than 4,000 lbs (it will) the Bulldog Powered-Drive Trailer Jack # BD500200 that you referenced would work great for you. Check out the review video I attached for more info as well.
view full answer... - Wil The Bulldog Powered Drive Trailer Jack # BD500200 Fit A Trails West Horse Trailer To know if the Bulldog Powered Drive Trailer Jack # BD500200 will fit your trailer you'll just need to measure the bolt pattern and outer tube thickness of your current jack to see what size will fit. This jack has a 2-1/4" outer tube diameter, which is the most common thickness, but I have had a few people with a slightly smaller cutout hole so I recommend checking beforehand. There are two sets of mounting holes on this jack that are both spaced 3-1/4" apart center-to-center and are...
view full answer...
- Travel Length and Extended Length of Bulldog 4,000 lb Powered Drive Trailer JackThe specifications we have for the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs # BD500199 (Black) and # BD500200 (White) are the correct ones. We take these measurements ourselves and the 31-3/4" extended height and total lift of 22" (14" of screw travel and 8" of drop leg travel) are the correct specs. Bulldog replaced an older jack with this Powered Drive jack, and the specs you referenced are for the older, discontinued jack so Bulldog may not have...
view full answer... - Recommended Electric A-Frame Jack To Replace Manual Jack On Haulmark Tandem Enclosed TrailerIt sounds like the Bulldog A-Frame Jack, part # BD500200 is just what you are looking for. The BD500200 has an outer tube diameter of 2-1/4 inches which matches what you are replacing and this jack has 2 toggle switches. One is used to control the up and down movement of the jack and the other switch turns the LED lights on and off. The mounting plate features mounting holes that allow you to mount it so the controls are at the front of the jack or mount it so that the controls are on...
view full answer... - Why Wouldn't 12 Volt Accy Circuit of 2022 Ford F-150 be ActiveYour 2022 Ford F-150 does have the 12 volt accessory circuit on the 1:00 pin but your truck needs to sense a trailer connection for the circuit to activate. A lot of people with your truck struggle with this feature as sometimes trailers with LED lights create issues with the 12 volt circuit activating or not. For a lot of people it's just simpler to bypass the factory wiring for this circuit by running 10 gauge wire like part # 10-1-1 from battery to the 7-way through a breaker # 9510.
view full answer... - A-Frame Electric Trailer Jack for Car HaulerThe Bulldog Powered Drive Jack part # BD500200 would be an excellent choice for your car trailer. It has a 4,000 lifting capacity which would easily handle the tongue weight capacity of your trailer and would make life much easier than hand cranking your current hand winch!
view full answer... - Can I Wire and Electric Trailer Jack Directly to the Truck BatteryYou could technically wire an electric trailer jack directly to your truck's battery, but that isn't really the most practical setup. I've seen one guy pull out his jumper cables every time he wanted to use the jack in this fashion, but I can't say the safety factor didn't worry me. Another thing to consider is that the wire gauge used on electric trailer jacks isn't the most ideal for running up to the front of a truck due to the wire length required and the amp draw of the jack motor....
view full answer... - Availability of a Powered Trailer Jack with a 3-1/4 Inch Center to Center Mounting PatternThe powered A-frame jacks we carry (see link) have a standard mounting hole pattern used by most trailer manufacturers. For example, the Bulldog Powered-Drive Trailer Jack, # BD500200, has two sets of mounting holes. One is 2-1/2 inches on center, the other is 3 inches on center. However, you could use a drill to elongate the mounting holes accommodate a 3-1/4 inch pattern.
view full answer... - Need Replacement Extend and Retract Switch for Bulldog 4000 LB Powered-Drive Trailer Jack # BD500200Yes, we do offer a replacement extend/retract switch for your Bulldog 4000 LB Powered-Drive Trailer Jack, # BD500200. You will need part # BD500363.
view full answer... - Could the Bulldog Jack part # BD500185 Use a Previous Powered Jacks Wiring to InstallThe Bulldog Jack part # BD500200 should install just fine with the previous jack's wiring as long as the wire from the previous jack has the same gauge as the wire from this jack. If the previous wire looks much thinner then I would recommend you not reuse it and run new wire. I attached an install video for you to check out as well.
view full answer... - Troubleshooting Bulldog Power Jack BD500186 that Drains Trailer Battery After Several UsesFirst you will want to use a circuit tester like part # PTW2993 to test the 12 volt accessory circuit of your 7-way. There should be voltage on this circuit, if not check the fuses of your tow vehicle as most likely one has blown. This is probably the issue. If there is voltage there you will want to test the wire that leads to the battery with the trailer connector connected but the wire disconnected from the battery so that you can tell if the voltage on the circuit is coming from the...
view full answer...
Do you have a question about this Camper Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Jeffrey L
Edited by:
Lindsey S
Video Edited:
Jacob T
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Mike S
Updated by:
Isabelle B
Updated by:
Noah M
Installed by:
Cole B
Written by:
Shelly K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Shorty S.
1/25/2018
Still lifting and lowering my trailer as designed. Having used the jack up to 6-8 times a month, I is withstanding the rigors of hauling. The little bubble level on top of the jack is pretty much useless in my application besides, the bubble is now about the length of the vial. Short of that, Id recommend to others. I am please with this product and sometimes wonder if I should have purchased the next size up.