Dimensions for Installation of a Bulldog Electric Powered Trailer Jack with Propane Tanks on Tongue

Question

Question:

Please, what is the measurement from the bottom of the housing to the top of the mounting plate on the Bulldog electric tongue jack model BD500200? I want to make sure it clears the propane tank covers when installed. Thank you!

asked by: QUANAH

0

Expert Reply:

The distance from the top of the mounting plate to the bottom of the housing on the Bulldog Powered-Drive Trailer Jack, # BD500200, is 13 inches.

expert reply by: Robert G

0

Answer 1

To determine if this powered drive trailer jack will fit on your existing trailer and current set up you will need to measure from the center of the current mounting jack rearward. The Bulldog powered drive trailer jack that you referenced needs at…

view full answer...

Answer 2

The inner leg of the Bulldog Powered Drive Trailer Jack #BD500200 that you referenced is a solid tube. It does not have a welded seam that runs up the leg of the jack.

view full answer...

Answer 3

From the center of the shaft to the front outside edge of the motor housing is 3-1/2 inches. I included some of the mounting plate when I measured for height, which is 8-1/4 inches, since that sticks out over the shaft as well. I also measured from…

view full answer...

Answer 4

The Diameter of the main tube is 2-1/4 inches on the Bulldog Powered-Drive Camper Jack, item #BD500200. There are 6 holes in the mounting plate for either 2-1/2 inch mounting pattern or 3 inch mounting pattern. These are the standard bolt patterns…

view full answer...

Answer 5

I had our warehouse measure the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White #BD500200 and it measures at 4-1/4" wide as shown in the included diagram. I included a video of the #BD500200 for you to…

view full answer...

Answer 6

The specifications we have for the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs #BD500199 (Black) and #BD500200 (White) are the correct ones. We take these measurements ourselves and the 31-3/4" extended…

view full answer...

Answer 7

The Bulldog Powered Drive a-frame trailer jack #BD500200 is circuit protected internally so additional fuses or breakers are not required. The jack should be ran off of a trailer mounted battery and not off of the 12 volt circuit through the trailer…

view full answer...

Answer 8

The Bulldog Powered-Drive Trailer Jack #BD500200 would do well as a powered jack for your 6500 lb trailer. It would also work to jack up your trailer to install the weight distribution system you have. This jack can lift trailers with up to 4,000 lbs…

view full answer...

Answer 9

For your Bulldog Electric camper jack #BD500200 will run just fine off of any 12V battery. Often the trailers that use these jacks will have other components they will run as well like lighting, vent fans, etc so it is recommended to use a deep cycle…

view full answer...

Answer 10

Sounds like the inner screw of the Bulldog Powered Trailer Jack part #BD500200 that you have is damaged which would require the jack to be replaced. If it's less than 5 years you might be able to get it warrantied but otherwise you'd need to…

view full answer...

Answer 11

If your 4K Bulldog A-Frame jack like part #BD500199 or #BD500200 is struggling under the tongue weight of a 14,000 lb trailer then I would have to agree that it likely isn't getting the power it needs from the 7-Way on your truck and using a…

view full answer...

Answer 12

The Bulldog Powered-Drive Trailer Jack, item #BD500200, only has one wire, the power wire. This jack attaches to ground through the mounting hardware and the trailer frame. When wiring the jack to your 7-Way trailer connector you will need to make…

view full answer...

Dimensions for Installation of a Bulldog Electric Powered Trailer Jack with Propane Tanks on Tongue

Continue Researching