9" Wide x 65" long x 15" tall. These sturdy teardrop fenders protect your tandem-axle trailer from road debris. 16-Gauge, cold-rolled steel is durable. Bolt or weld onto your trailer.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 11-1/2" and 12" round jack ... Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
Increase the surface area of your camper's leveling jackfoot to help prevent sinking and to get added stability. Durable rubber pad easily and permanently snaps into place.Features: Heavy-duty rubber pad snaps onto the foot of your camper jack for extra stability Prevents sinking into soft ground Durable, heavy-duty rubber is made from recycled tires Grips uneven
Marine-grade hub is designed for trailer idler axles. Fits 2K Dexter E-Z Lube and etrailer Easy Grease axles with BTR spindles. Inner bearing (L44649) and race, outer bearing (L44649) and race, grease seal, grease cap, and nuts included.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 10" octagonal or round concave ... Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
Determining the correct rise or drop for your Blue Ox SwayPro Weight Distribution System #BXW1000 is going to be the same method as determining rise or drop for a standard ball mount. You will just need to measure from the ground to the top of your…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…
The prep you mentioned is more than adequate prior to applying the Alpha Systems 4034 Roof Coating for RV Roofs #AL34CV. According to the instructions you only need to apply the Primer #AL77CV if you're applying this to an EPDM membrane. In that…
Sorry to hear about the troubles you're having! To remove the Alpha Systems 4034 Roof Coating for RV Roofs #AL34CV from the side of your 1998 Tiago, you can use: - A type of chemical paint remover, - A Paint scraper tool, - A Pressure washer, Or…
Slipper Springs like #e33SR do not use a bolt and bushing for the open eye end of the spring. It connects directly to the hanger using a slipper spring hanger kit.
What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…
I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
The Dexter 072-078-00 is a 2,200 lb capacity leaf spring. You can use a higher capacity leaf spring, however it won't increase the capacity of your trailer as the axle is still rated for that max capacity of 4,400 lbs. My recommendation for a…
As long as you aren't exceeding the speed rating of the tires which would cause them to get to an excessive heat you are fine. Trailer tires are designed to be inflated to their max PSI rating when cold and then the pressure increase from heat…
Your 2008 Chevy HHR should have a set of rails on the roof that run from front to back. Which means we have the Rhino Rack part numbers #RRVA106B-2 and #RRSX100 as a confirmed fit, but the kit you mentioned is not a fit.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 8" round jackfoot.Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 10" round jackfoot.Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
Designed for hydraulic lift or dump trailers, this smart charger can be mounted inside the hydraulic pump or lift motor housing. Creates a shore power plug, which lets you plug in an extension cord to draw power from a wall outlet.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 8" square jackfoot.Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
This 5/8" diameter receiver lock codes to your vehicle's ignition key. Made of automotive-grade materials and nearly impossible to pick or bump, this corrosion-resistant lock helps keep your ball mount safe and secure.
Replaces 1 missing or damaged jack pad for your Lippert, Pac Rim, or Venture leveling system. Large surface area adds stability on soft ground. Fits with 9" round jack feet (SC39MR, SC99MR ... Features: Replaces 1 missing or damaged shoe pad for your Lippert, Pac Rim, or Venture leveling system Pad increases the surface area of the jackfoot to help prevent sinking and provides added
This fully welded, corrosion-resistant vehicle trailer hitch receiver is perfect for your light-duty towing needs. Draw-Tite's Tested Tough guarantee ensures that this hitch exceeds industry standards. Drawbar sold separately.
Replaces 1 jack pad for your Equalizer Systems leveling system. Large surface area adds stability on soft ground. Fits 11-1/2" round jack feet.Features: Replaces (1) 12" jack pad for your Equalizer Systems leveling system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made
This replacement inner member slide fits into the existing outer member housing of your Dexter DX7.5L and Legacy UFP surge brake actuator. For use with single-axle trailers with hydraulic disc brakes.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 9" round jackfoot.Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
Replaces 1 missing or damaged jack pad for your Equalizer Systems leveling jack. Large surface area adds stability. Fits Equalizer Systems with 10" round or octagonal jack feet (SC79MR, SC89MR ... Features: Replaces 1 missing or damaged shoe pad for your Equalizer Systems leveling jacks Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made
This Spectro trailer wiring junction box provides a fast, easy way to connect the wires from the trailer connector to the wiring for either a 6-way or 7-way connector. Makes replacing your trailer's connector simple.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 7" square jackfoot.Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
9" Wide x 68" long x 17" tall. These sturdy teardrop fenders protect your tandem axle trailer from road debris. 16-Gauge, cold-rolled steel is durable. Bolt or weld onto your trailer.
Replaces 1 pad for your SnapPad jack stand pad system. Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability. Fits 5-1/2" square jackfoot.Features: Replaces 1 pad for your SnapPad jack stand pad system Pad increases the surface area of the jackfoot to help prevent sinking and provides added stability Made in the USA Specs: Application
Filter Results
