I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…
Hey Charles, Yep, the Demco Autoslide 5th Wheel Trailer Hitch for Chevy/GMC - Single Jaw - Underbed #DM36SV is a kit that includes the Underbed Rail and Installation Kit #DM8551004 and the Demco Autoslide 5th Wheel Trailer Hitch #DM8550022. The…
Hey Duane, The Hellwig kit you referenced was designed for trucks and would not work for your trailer but we can still help. What you'd want instead is the SumoSprings kit part #TSS-106-40 which is for lighter duty trailers with underslung…
Hi Frank, While we can get you a brake controller for your 2020 Chevy Colorado, there isn't a plug-in option and harness because the truck doesn't have a plug under the dash. That said, the wires are already run to the cab, so it isn't…
Hey Corry, you would basically want to mock up the Terran Industries Tandem-Axle Hanger Kit #TX85VJ with the 26-5/8 inch springs that you have and have the springs temporarily mounted in the hanger and the equalizers to get the correct dimensions to…
Hey Marc, it's the lower of the two holes in the Demco EZ Latch Coupler part #DM16080-95 that gets used for the hitch lock. We have that with part number #IR66FR which was specifically designed for this coupler.
The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…
Hey Rylan, I checked with Demco for you, and the Demco A-Frame Cast Head Coupler #DM37ZR will need Grade 5 hex bolts for installation. We don't have these but they can be found at any local hardware store.
Hi Kieran! I can definitely get you measurements for the Lock N Roll Articulating Flat Mount Trailer Coupler - Trailer Side - 10,000 lbs #LR77FR. The whole plate measures 3-1/4" x 9" and when measuring center to center, I got 2-1/8"…
Hello David, thanks for reaching out. It is possible to switch your trailer over to a lunette ring/pintle hitch system. Basically you will need to replace your current A-frame coupler with a channel coupler like part #LR76VR. This will allow you to…
Yes, you will be able to replace your stock coupler with the Demco 50-Degree A-Frame Trailer Coupler #DM13205-95 as long as you have a standard a-frame trailer. I attached a picture below of the dimensions below so you can see if it would work for…
Hey Jon, welcome back! Those are indeed for safety chains. The chain anchor holes are 1/2" in diameter on the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole item #DM13205-95. To attach a set of safety chains like the item #BPH94MR to them…
I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…
Hey Charles, Yep, the Demco Autoslide 5th Wheel Trailer Hitch for Chevy/GMC - Single Jaw - Underbed #DM36SV is a kit that includes the Underbed Rail and Installation Kit #DM8551004 and the Demco Autoslide 5th Wheel Trailer Hitch #DM8550022. The…
Hey Duane, The Hellwig kit you referenced was designed for trucks and would not work for your trailer but we can still help. What you'd want instead is the SumoSprings kit part #TSS-106-40 which is for lighter duty trailers with underslung…
Hi Frank, While we can get you a brake controller for your 2020 Chevy Colorado, there isn't a plug-in option and harness because the truck doesn't have a plug under the dash. That said, the wires are already run to the cab, so it isn't…
Hey Corry, you would basically want to mock up the Terran Industries Tandem-Axle Hanger Kit #TX85VJ with the 26-5/8 inch springs that you have and have the springs temporarily mounted in the hanger and the equalizers to get the correct dimensions to…
Hey Marc, it's the lower of the two holes in the Demco EZ Latch Coupler part #DM16080-95 that gets used for the hitch lock. We have that with part number #IR66FR which was specifically designed for this coupler.
The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…
Hey Rylan, I checked with Demco for you, and the Demco A-Frame Cast Head Coupler #DM37ZR will need Grade 5 hex bolts for installation. We don't have these but they can be found at any local hardware store.
Hi Kieran! I can definitely get you measurements for the Lock N Roll Articulating Flat Mount Trailer Coupler - Trailer Side - 10,000 lbs #LR77FR. The whole plate measures 3-1/4" x 9" and when measuring center to center, I got 2-1/8"…
Hello David, thanks for reaching out. It is possible to switch your trailer over to a lunette ring/pintle hitch system. Basically you will need to replace your current A-frame coupler with a channel coupler like part #LR76VR. This will allow you to…
Yes, you will be able to replace your stock coupler with the Demco 50-Degree A-Frame Trailer Coupler #DM13205-95 as long as you have a standard a-frame trailer. I attached a picture below of the dimensions below so you can see if it would work for…
Hey Jon, welcome back! Those are indeed for safety chains. The chain anchor holes are 1/2" in diameter on the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole item #DM13205-95. To attach a set of safety chains like the item #BPH94MR to them…
Weld-On A-Frame Trailer Couplers are perfect for those seeking a robust and reliable connection. Ideal for heavy-duty applications, these couplers ensure a secure fit with a 32-degree angle, making them suitable for various trailer types, including V-nose cargo trailers.
Weld-On A-Frame Trailer Couplers are known for their strength and durability. They are crafted from high-quality materials, ensuring they can withstand the rigors of heavy-duty use. Their robust construction makes them perfect for trailers that require a secure and long-lasting connection, even in challenging conditions.
To ensure a proper fit, check the angle of your trailer frame. These couplers typically fit a 32-degree angle, which is common in many trailers. It's crucial to verify this angle to avoid the need for additional modifications, like shims, ensuring a seamless and secure installation.
Yes, with the right tools and preparation, installing a Weld-On A-Frame Trailer Coupler can be straightforward. Ensure the trailer frame is clean and free of paint where the coupler will be welded. This will help achieve a strong weld and secure attachment, providing peace of mind on the road.
Weld-On couplers offer a more permanent and robust connection compared to bolt-on options. They are less likely to loosen over time, providing a more reliable and secure attachment. This makes them ideal for trailers that experience heavy use or travel over rough terrain.
Absolutely! These couplers are versatile and can accommodate various trailer types, including V-nose cargo trailers and off-road teardrop trailers. Their design ensures a strong connection, making them suitable for a wide range of applications and trailer configurations.
A-Frame Trailer Coupler Parts or Accessories
Filters
