1. Home
2. Trailer Parts
3. A-Frame Trailer Coupler
4. Standard Couplerx

Based on your measurements it matches our Fulton 50-Degree A-Frame Coupler #FE443050303 which looks to be the same as what is on the 2024 Intech Sol Horizon from the videos I could find. So this would use either the EZ Latch #DM14793-81 or…

...side, which will give you a 50 degree angle for the coupler. The standard dimension for trailer tongues is 50 degrees so most likely the tongue on your trailer will accept the Atwood A-Frame...

...The etrailer A-Frame Trailer Coupler w/ Round Jack Hole # CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest...

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

...I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design...

Hello Bill, thanks for reaching out. I cannot say I have ever heard a complaint about a Demco Ez-Latch Coupler like part #DM37ZR failing and coming disconnected. I ran your question by a group of my associates here and not one of them could recall…

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts per…

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

Yes, you can replace your weld-on coupler with a bolt-on. You'll just need to drill the holes. Then, if you wanted to go back to a weld-on later that would be fine too. Just to confirm you can check with the trailer's manufacturer that…

Hello Ryan. The #CA-5196-B Ram Sleeve Lock A-Frame Trailer Coupler and the Bulldog #BD028288 are fairly similar. They are both 50 degree a-frame couplers designed for a 2" ball and both are about 16" long overall. The main difference is the…

Based on my research the Shelby 5101 is an A-frame coupler with a 2" ball and 5,000 lb capacity. We have exactly that with the A-Frame Coupler #CA5100B, which has a trigger latch and has a black paint finish. The same coupler is available with a…

The Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301, does not come with the attachment bolts. I have attached two images showing the bolt pattern measurements and the bolt hole sizes. I would recommend using grade 8 bolts, but grade 5 is acceptable…

Based on your measurements it matches our Fulton 50-Degree A-Frame Coupler #FE443050303 which looks to be the same as what is on the 2024 Intech Sol Horizon from the videos I could find. So this would use either the EZ Latch #DM14793-81 or…

...side, which will give you a 50 degree angle for the coupler. The standard dimension for trailer tongues is 50 degrees so most likely the tongue on your trailer will accept the Atwood A-Frame...

...The etrailer A-Frame Trailer Coupler w/ Round Jack Hole # CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest...

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

...I checked the Featherlite Trailer website for specs on the model 3116 trailer but this part number returned no results. But if your trailer uses an industry-standard 50-degree a-frame design...

Hello Bill, thanks for reaching out. I cannot say I have ever heard a complaint about a Demco Ez-Latch Coupler like part #DM37ZR failing and coming disconnected. I ran your question by a group of my associates here and not one of them could recall…

To install the Demco A-Frame Trailer Coupler #DM16680-52 that you referenced, you will want to use 3/8 inch, grade 5 bolts , approximately 1-1/2 inches long (depending on how you are installing the coupler). You will want to use 5 of these bolts per…

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

Yes, you can replace your weld-on coupler with a bolt-on. You'll just need to drill the holes. Then, if you wanted to go back to a weld-on later that would be fine too. Just to confirm you can check with the trailer's manufacturer that…

Hello Ryan. The #CA-5196-B Ram Sleeve Lock A-Frame Trailer Coupler and the Bulldog #BD028288 are fairly similar. They are both 50 degree a-frame couplers designed for a 2" ball and both are about 16" long overall. The main difference is the…

Based on my research the Shelby 5101 is an A-frame coupler with a 2" ball and 5,000 lb capacity. We have exactly that with the A-Frame Coupler #CA5100B, which has a trigger latch and has a black paint finish. The same coupler is available with a…

The Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301, does not come with the attachment bolts. I have attached two images showing the bolt pattern measurements and the bolt hole sizes. I would recommend using grade 8 bolts, but grade 5 is acceptable…