What Is The Drop Leg Hole Spacing On The Pro Series Square Jack PS1400990376?

Question

Question:

What is the spacing on the holes? I am looking for 12inch of travel and 2inch hole spacing the pair with an existing jack I have.

asked by: Pete M

0

Expert Reply:

Hey Pete, thanks for reaching out. If you are referring to the hole spacing on the drop leg, those holes are 3-1/2" apart on center.

Was that what you were wanting to know? Or something else?

expert reply by: Jesse M

0

Pro Series Square Jack Drop Leg Hole Spacing
(click to enlarge)

Answer 1

If you need a dual jack setup then you would need to go with a landing gear set like the Bulldog Tandem Landing Gear Set #BD500162. The #PS1400850383 would not be able to used as a dual jack setup.

view full answer...

Answer 2

There really isn't a specific width (or thickness) of a winch mounting plate to use with a 12,000 lb winch. You just want to choose one that has a mounting bolt hole pattern that is compatible with your winch. The Bulldog Winch Hitch Mounted…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Is The Drop Leg Hole Spacing On The Pro Series Square Jack PS1400990376?

Continue Researching