What Is The Angle For The etrailer A-Frame Trailer Coupler?

Question

Question:

The angle requires the length of smallest and largest distance of the nose and the distance between them. Can you please provide the approx. distance and respective Smallest and largest sides. Thank you.

asked by: Shreyas J

0

Expert Reply:

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole # CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include this information in the picture below.

expert reply by: Bud M

0

A-Frame Trailer Coupler Angle
(click to enlarge)

Answer 1

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 2

Because they consider it proprietary information, the manufacturer will not provide a build sheet or detailed drawing of the #CA5100B. I believe you're needing the angle of the A-frame trailer tongue which would be equal to the angle of the two…

view full answer...

Answer 3

So long as your Airstream trailer has an A-frame, then yes, you can use the A-Frame Trailer Coupler - Underslung #CA-5335-B. There is no way for us to know what couplers fit any specific trailer, but so long as you have an A-frame then there…

view full answer...

Answer 4

Thanks for that photo, I do appreciate it. And all of the couplers we have - and indeed all the ones I am aware of - require a frame that is fully engaged. While Demco was not able to provide a dimensional drawing, we did measure the Demco 50-Degree…

view full answer...

Answer 5

I recommend installing the A-Frame Trailer Coupler #CA-5280-RB on your trailer. This has a cutout with bolt holes for a tongue jack. It places the opening where it is structurally stronger so it is less likely to bend like your current coupler.

view full answer...

Answer 6

If you have already added the fuse and the trailer charge circuit is not activated in the 2019 Ford F-350 Super Duty with factory integrated brake controller, then you want to make sure the trailer is connected and you press the brake according to a…

view full answer...

Answer 7

The wiring on your 2019 Ford F-250 Super Duty is a little goofy and it's something that a LOT of people have complained about with the newer Ford pickups. To get power back to your trailer jack you'll have to close your driver's door,…

view full answer...

Answer 8

Hey Sam, thanks for reaching out. We do have 2-5/16" A-frame couplers, but I am not seeing we have one with a yoke-style latch. If you want something similar, the A-Frame Trailer Coupler #CA-5280-RB fits a 2-5/16" ball and has a…

view full answer...

Answer 9

We do carry replacements for the Carefree brand. From what I have found, yours has 67" long arms on your 2017 Coleman 3015bh. The ones we offer are designed by Solera and are universal. They match the design of your current arms however; are…

view full answer...

Answer 10

Ram couplers are solid couplers that as long as you stay under the capacity of them they will work great. I would not recommend a 12.5k coupler on a 14k trailer though. Instead you'd want to go with a coupler with a 15k capacity like the part…

view full answer...

Answer 11

The best replacement option we offer for a Dometic WH-6GA RV Water Heater is tankless, the Furrion RV Tankless Water Heater part #FR68SR which is gas only. It won't be a direct replacement but still pretty easy nonetheless as they are very…

view full answer...

Answer 12

The correct replacement for your Klauber K01431B300 slide-out motor is the Replacement Motor Assembly for Lippert RV Slide-Outs - Klauber A-300 Model #LC157511.

view full answer...

What Is The Angle For The etrailer A-Frame Trailer Coupler?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching