Summer Starts Here - Save up to 70%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
8-5/8" x 3-1/4". LED trailer light with ABS mounting bracket illuminates your license plate. Durable polycarbonate lens and housing. Surface mount to trailer with bracket. 2-Wire design.
Features:
Specs:
California residents: click here
Average Customer Rating: 4.6 out of 5 stars (302 Customer Reviews)
8-5/8" x 3-1/4". LED trailer light with ABS mounting bracket illuminates your license plate. Durable polycarbonate lens and housing. Surface mount to trailer with bracket. 2-Wire design.This is one of the few license plate lights that would work for me. As you can see in the picture I have it mounted on top of the license plate, above the lamp. The attached bracket made for an easy installation. The wires were kind of short (about 8") because of the way I mounted it so I had to extend to wires.
I did not want to mount my plate on the bottom of the tail lamp assembly to utilize the built-in license plate light because it was to low to the ground and was always dragging loading and unloading the trailer. The product made an easy DIY modification to keep me on the good side of the men and women in blue.
Based on other reviews of these lights, I had no doubt that they would be brighter than the Bargman Series 92 incandescent lights that came standard on my trailer. The issue was whether or not the 12-13 degree return slope on the back of my trailer (see picture) would adversely affect their visibility because some LED lights are "directional. The bottom line is that I think they work very well despite the slight downward aim. The attached video shows my test of one of the new lights taped into position (right) compared to one of the old lights (left). The video does not due justice to the brightness of the new fixture, but you can clearly see how much sharper the "flash" of the light is compared to the old one. Two notes regarding installation; (1) there is very little space in the back of the fixture for wires so you need to be able to center the fixture on the whole in the trailer to push extra wire into, and (2) yo can configure these lights to be 1/2 stop/tail and 1/2 turn/tail if your trailer is wired appropriately.
Product worked perfectly for what we were using it for. I purchased a motorcycle and needed to move the license plate bracket to be able to add bags. I found your bracket online, knowing we were going to have to jerry rig it to where we wanted to mount it. I was a little suprised the bracket was plastic when I received it, but still worked great. A friend made 2 mounting brackets from a flat bar, cutting and bending them to the length and angle we needed. Drilled holes and mounted them under the rear fender. Mounted the license plate bracket on the other ends of the custom brackets and wired it in for lights.
Only 1 of the 5 LED’s work. Disappointing.
The picture isn’t that great due to the reflection, but only the center led is lit.
Item showed up early ,and was8 what I o rd9ered
Just wanted to tell you that I have finally installed the product I ordered
from etrailer.com, and I must say that it is by far the best product I have
ever used. They are bright, and very visible even during daytime. Attached is the finished product that I installed on my travel trailer. I
hope that other consumer like me will find this very helpful to buy from
etrailer.com.
Needed rear license holder when installing new Bragman LED surface mount lights.
Holder was easy to install an works great.
Exceptional and inexpensive LED-lit license plate mount/bracket.
I ordered this item (online) on a Sunday, and received a human confirmation e-mail that evening! Item was shipped the next day (Monday). Very Easy installation. Photos (3) attached. If you need an illuminated license plate bracket, BUY THIS ONE!
This license bracket was just what I needed to replace a broken one on my RV. This unit is well made, with a nice finish and a bright light. Better than original equipment!
Nice sturdy bracket and matches my new tail lights. Led and bright. Just what I wanted. I will attach a photo.
The Clear plastic lens keeps coming unsnaped from the rubber base. Had to use gorilla glue to keep it in place.
Jenny N.
6/2/2023
I would say that this is not normal with this bracket. I will have our Customer Service team reach out to you.
The led lights look great and were easy to install . The license plate holder finished the off the project.
Don B.
5/27/2018
They are still working great and looking good
This kit works, but not in the configuration delivered. If you purchase this, be prepared to find an alternate method to mount the lights. You will likely need to modify the cargo carrier to make this work.
The lights are sealed units that are normally flush mounted on larger trailers. Mounts have been added with self-tapping screws that easily strip out of the housing and the mounts fall off the lights. The screws in the kit were smaller in diameter than the holes in the mounts, both front and back, making them useless. I tried attaching the lights using zip ties and just the mount on the light portion, but that failed when the mount screws stripped out of the lights. I did not have the issue with the wiring being too short like other reviewers. My wiring was actually a little too long.
To actually install this kit reliably, here what you need:
- Silicone
- Super Glue
- Screwdriver (Flat or Phillips Depending on Screw Choice)
- Wire Cutters (To Cut the Ends off of Anchors)
- 9/32" Drill Bit
- 4x #6x1.5" Machine Screw
- 4x #6x0.75" Anchors
How I installed mine:
1. Remove the plastic bracket supplied with the light. Fill the holes with silicone so that the lights are sealed again. Check in a couple minutes to ensure that the silicone didn't drip through. Add more as needed until the hole is filled.
2. Trim the ends off of your anchors so that they fit in the two plastic circles on the back of the lights. Just a little bit will do. Test fit them to make sure they go all the way in. Once you're sure they fit, super glue just the bevel at the top to the light. This is to prevent them from turning in the hole because the plastic on the light is really smooth.
3. Drill two 9/32" holes in the rear upright bars of the carrier. Make the holes 1/4" from the edge so you can still connect the wiring. Space the holes at 2 5/16". The holes need to go through the front and back of the uprights.
4. Put the screws through the back holes pointing outwards. Once the super glue has dried, screw the screws into the anchors.
5. Connect the wiring per the supplied instructions.
The light worked perfectly for my needs. I am very happy with it
Rich Z.
2/1/2019
All is well. Thanks
This worked very well to mount and light my license plate when I removed the OEM lights that had an integrated mounting for the plate. It was easy to mount and wire to the existing trailer license plate lighting circuit. I'm very pleased with the finished result.
Jack
6/14/2021
It has worked perfectly. Illuminates the license plate and provides a mounting point.
good product. would buy again.
A year has passed since I installed my LED trailer tag light/bracket and it’s still working as good as the day I installed it.
David M.
11/12/2020
Working great
etrailer had everything in stock
Fast shipping too
Very happy and will be a repeat customer
I did a little engineering on it, but it did a great job. Even a Police Officer at the beach commented positively about it.
The first license plate lights that doesn't break when you back your boat trailer into the water while it's running. Yea LEDS!
Philip
6/18/2019
Many a loaded trailer trips and all is still doing great! Its so nice when a product works like it should!
Wish it had been made of metal and a little more depth for wiring storage.
This plate mount with light is the exact replacement part for my boat trailer.
Perfect! And of course E-Trailers service is consistently fantastic! Thanks team!
Nz2721743 S.
12/3/2017
Light still performing as required!
I like the idea that this product has a lifetime warranty on the lights if they should burn out. Very pleased with the difference over factory installed lights.
Maurice
2/13/2021
Very Well, Well made
Warning, this item does not run off of batteries!
I hope you have not received this because etrailer is not responsible for shipping on returned items! This item will cost me more to return (shipping) then it's worth! I guess I'm just supposed to throw it away and be happy about. This is a bad return policy!!!
They had the part I needed on an older model travel trailer and they sent it right away.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
8/14/2023
The LED lights are covered under warranty. I will have our Customer Service team reach out to you.