8-11/16" x 3-13/16" Rectangle. LED Trailer light with 22 diodes provides stop, turn, tail, and license plate light functions. Durable black polycarbonate base. Surface mounts to driver side of trailer with included bracket. 3-Wire pigtail.
Features:
Specs:
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today, we're gonna be taking a look at the Command LED trailer taillights for the driver's side. These are available with either a black or white base. You could also purchase these for the passenger side. These DOT compliant LED lights are gonna give your brake lights, your right turn signal, your left turn signal and your running lights. The driver's side is gonna feature a license place bracket and a license plate light. You will have to provide your own hardware to mount your license plate.
Each light features 22 LED diodes. LEDs can last up to 50 times longer than incandescent bulbs. This means you won't have any bulbs to replace and they're gonna provide a brighter light with less power. The overall dimensions are 8 11/16" long, 3 13/16" tall and 2" deep. These are gonna be great for your camper or trailer.
They're non submersible lights. So don't put them on your boat trailer. Please note that the driver and passenger side are sold separately. Many customers are using these to upgrade their traditional incandescent lights. Compared to incandescent lights, these will last longer, use less power and there are no bulbs to replace.Now that we've gone over the features, I'll go ahead and show you how to get it installed.
Here's what our old incandescent taillight looks like. We're gonna be upgrading it LED. Let's go ahead and get started. Let's go ahead and take off the cover and we can do this by using a flathead screwdriver. We're going to push in the tab and then take the cover off.
Now we're gonna remove the hardware. We're gonna save our screws because our new light does not come with. With our hardware removed, we can go ahead and take it off and expose our wiring. As you can see, around the edge, we had some leftover calk. We need to make sure that's nice and clean before replacing it with our new light. Now our old light used quick splice connectors. We're gonna be use butt connectors so we'll need to cut all of these out. We're gonna cut here and here. Cool. Now, I'm gonna strip back these wires and then add on my butt connectors. If you need some butt connectors, you can find them on our website at etrailer.com. Just stripping them back just a little ways.Then with my double green wires, just gonna make sure you twist them together a little bit. Take a butt connector. Make sure it's all the way on and then crimp it together and then I'll do the same for the rest of my wires. Now let's bring in our new light. I've already gone ahead and removed the lens. My white is my ground. My red is my brake and turn and my brown is my running lights. I'm gonna connect white to white. Make sure it's good and crimped and then red to red and then finally, brown to green and then we can test it out. Here's our running lights, our turn signal, and our brake. With everything working properly, we can tuck our wires back in. Now you'll wanna be sure that our tabs are facing down for our license plate. Hold it in place inaudible 00:03:27 was a replacement. It's the same size as our light. We can just put our hardware back in the same holes. I'll get one started and then I'll just work my way around. Then we can place on our lens. Now our passenger side installs the same way.The only difference is there's no license plate light or bracket. Make sure it snaps in on both sides and then we've got it. This is our passenger side. If you'd like to, you can run some calk around the edges just to keep that water and moisture out. With both lights working, we're all set and that completes our look at the Command LED trailer taillights in either black or white for the driver and passenger side.
Average Customer Rating: 4.8 out of 5 stars (8 Customer Reviews)
8-11/16" x 3-13/16" Rectangle. LED Trailer light with 22 diodes provides stop, turn, tail, and license plate light functions. Durable black polycarbonate base. Surface mounts to driver side of trailer with included bracket. 3-Wire pigtail.
Nice lights. Work great. 672035
Sleek and modern looking.. But can't believe it had a incandescent bulb in instead of an LED for the license plate..! That's the whole idea in the change out. It's to get rid of incandescent..lol 716735
A perfect fit to replace the original camper taillights. So much brighter with LEDs than with the old bulbs. Placed order on a Sunday and received on Wednesday. Light was exactly what was promised. Will definitely save this web site for future orders. 708087
Works great on my 2007 Jayco Pop Up, fast shipping. 727785
Gwen with etrailer was the Epitone of what customer service should be! The lights arrived right to my doorstep as promised and the quality is second to none! Of course this the why I will continue to shop etrailer 722597
Nice and bright. Easy to install. 666640
Great service prompt delivery! 665207
ARRIVED OK NO PROBLEM'S THANKS 559224
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.