Parts Needed To Install The Dexter Disc Brake Kit K2HR35DS On A 2024 Gateway Boat Trailer
Updated 11/17/2026 | Published 11/16/2026 >
Products Featured in This Question
Question:
Im planning to purchase two Kodiak K2HR35DS kits to replace all four hydraulic disc brakes on my 2024 Gateway tandem-axle boat trailer. The existing brakes are Dexter/UFP DB-35 integrated hub/rotor assemblies, marked 8-435 believed to be K08-435-05, with 5-on-4.5 wheel bolt pattern. The trailer uses integrated torsion suspension with four-hole brake mounting flanges measuring approximately 2? inches center-to-center. The existing caliper brackets use two of the four mounting holes. I found your previous QandA indicating that K2HR35DS can replace UFP DB-35 assemblies when using Dexter 168255TB grease seals. Could you please confirm: 1. Will K2HR35DS fit my existing spindles and mounting flanges, including proper caliper bracket and rotor alignment? 2. Are four 168255TB seals required instead of the seals normally supplied with the Kodiak kits? 3. What inner and outer bearings, spindle hardware, and other components should I order to complete all four wheels? Im also replacing the original steel brake lines with Kodiaks 20TA-BLKIT marine flexible hose system and retaining my Dexter/UFP A-75 disc-brake surge actuator. Are there any compatibility concerns with that combination? Thank you!
asked by: Brad H
Expert Reply:
Hi Brad!
The Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet and Stainless - 3,500 lbs # K2HR35DS will Should be a great replacement for that UFP DB-35 kit you currently have installed. That used the #84 spindle (3,500 pounds) and is a very common spindle size. It's that 2" measurement you got for the mounting bolt pattern that made me say "should" though.
That typically measures 2-7/8" and is what you should also have as that is pretty standard. If you could double check the measurement and let me know what you get, I will see if we have something else that will work for you. If you do measure 2-7/8", I have the rest of your questions answered below.
For a bearing kit, we have a couple different options. If you will be running grease, you will want the Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle # BK2-100, or Timken # TMK52VR is you wanted American made. This includes inner and outer bearing, seal, tang washer, and a cotter pin. It also includes both inner and outer races, but those are pre-installed in the Kodiak kit, so you technically will have a couple spare parts. For 2 axles, you will need to get 4 sets to have everything covered.
If you will be running oil, you will want the Dexter # DX27UR kit. This uses the same inner and outer bearings, but includes an oil seal (like the # 168255TB you mentioned). It also includes the races and cotter pin, but also has a cap and doesn't include a tang washer. Again, you would need 4 of these to complete the install.
The Kodiak Hydraulic Brake Line Kit - Tandem Axle - 20' # 20TA-BLKIT will fit together with the # K2HR35DS kit perfectly and you will not need anything else to get it installed. That UFP A-75 brake actuator uses a 3/16" brake line fitting size, commonly utilizing a 3/8"-24 SAE thread pattern, which is what the # 20TA-BLKIT also uses. If you are missing that fitting, you will also want to grab the # T4750300 to adapt it over.
What kind of boat are you carrying? And where do you typically launch?
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet and Stainless - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >


Brad H.
11/17/2026
Thanks for the detailed response! I rechecked our earlier measurements, and the four-hole brake mounting flange is approximately 2-7/8" center-to-center, so that should match. One important detail: My original Dexter/UFP DB-35 hubs have the black VAULT bearing lubrication caps, which your other representative indicated likely means I have the UFP/Dexter marine spindle using the 168255TB seal. Given that, would you recommend the DX27UR bearing kits rather than the standard BK2-100 kits? Also, can the original VAULT caps and lubrication system be reused with the Kodiak K2HR35DS hubs, or should I convert to conventional grease with compatible seals and dust caps? The trailer is a 2024 Gateway tandem torsion-axle boat trailer, approximately 7,500 lbs overall. I haven't confirmed the individual axle ratings yet. I primarily launch in saltwater around the South Carolina Lowcountry. Thanks again! I'm hoping to get everything confirmed so I can order the two brake kits and hydraulic line kit.