See what our Experts say about this Optronics Trailer Lights

• 2-1/2" Long Submersible Clearance Lights With Clear Lens and Red LED For Boat Trailer
  Hey Zach, I have a solution for you, but the Thinline LED Clearance and Side Marker Light - Submersible Red # AL91RB and Thinline LED Clearance and Side Marker Light - Submersible Amber # AL91AB aren't available in clear lens with red LED. These units are typically found on light bars like the white with Red Lens # MCL84RB or black with Red Lens # MCL93RB. These are all submersible. That said, we do have some submersible clear lens with red LED that are also 2.5": - # TN52XR - # MCL13CR2B -...
  view full answer...
• Trailer ID Light Bar For Trailer Over 80 Inches Wide
  Since your trailer is over 80 inches wide, you do need the three-light ID bar, which is the following part number: - LED Identification Light Bar for Trailers over 80" Wide # MCL93RB
  view full answer...
• Availability of Trailer Taillight ID Bar that Has LEDs
  The Peterson ID bar part # 428100 is definitely an incandescent light setup but we do have a similar version that has LED lights with the part # MCL93RB like it sounds like you are looking for.
  view full answer...
• Lights Needed for 102" Wide x 25' Long Trailer
  The TecNiq Mini LED Trailer Fender Clearance Light # TN78XR can be used even though this isn't a boat trailer, and these can be installed on the sides of your trailer - you don't have to install these only on the fenders. For a complete light setup you need the following: - Optronics Trailer Light Kit for Trailers over 80" Wide # TL16RK - LED Identification Light Bar for Trailers over 80" Wide # MCL93RB I'm also attaching a link to our helpful article on trailer lights for you to check out.
  view full answer...
• Replacement LED for 2006 ShoreLandr Trailer with Alumacraft Boat
  I have some great LED replacement options for your 2006 ShoreLand'r Trailer with Alumacraft Boat. I have attched a list of these below. Please note, they may not all be exact fit replacements but with a bit of work they will be able to be made compatible no problem. LED Trailer Tail Light part # STL56RB (Passenger) LED Trailer Tail Light part # STL57RB (Driver) Redline Mini Thinline Clearance or Side Marker Light part # LT02-220 LED Identification Light Bar for Trailers over 80" Wide...
  view full answer...
  
• LED Light Kit for Trailer Over 80 Inches Wide
  The "80" you are referring to is the width of the trailer, and it makes it easier to determine the light kit you need. Since you need tail lights as well as running lights, I recommend the Trailer Light Kit for Trailers Over 80" Wide # TL16RK. This will give you the Stop, turn, tail, side marker, rear clearance, side reflector, rear reflector, and license plate light that you need for your trailer. For the light strip with three lights you were referring to you will need the LED Identification...
  view full answer...
• Amber Version of the Clearance Light part # MCL98RB Availability
  To get an amber, LED version of the part # MCL93RB you would need to order replacement lens part # A91AB and then replace the red lenses with the amber lens. On the front of a trailer you need to have the amber lights displayed and on the back red.
  view full answer...
• LED Identification Light Bar and Trailer Taillight Kit for 2012 Yamaha Trailer
  Yes, both of the LED trailer taillight kits you mentioned would work great on our 2012 Yamaha trailer. The LED Identification Light Bar # MCL93RB and the Optronics LED Combination Trailer Tail Lights # TLL160RK. These are both LED like you are wanting which means more reliable and less amperage draw, can easily fit in place of what you have now, and are submersible too.
  view full answer...
• Recommended U-Bolts, Rollers and Boat Trailer Lighting/Wiring for a 1984 Shoreline Trailer
  Thanks for sending us the pictures! Since you are installing a Bolster-and-swivel-bracket assembly part # CE10001G-4 and need a 4-1/8 inch width by 3-1/2 or 4-inch length U-bolt, we currently don't offer a close match. I would recommend going to a local hardware store to locate a U-bolt with the dimensions you need. I would go with a stainless steel u-bolt because it is corrosion resistant and ideal for marine applications. For the lighting and wiring on your 1984 Shoreline boat trailer,...
  view full answer...
  
• Checking/Fixing Ground Connection on Trailer LED Light Bar
  From what you describe, it sounds exactly like a ground problem. You'll want to make sure the ring terminal on the ground wire is making contact with bare metal on the trailer frame. If there's paint or corrosion preventing the ring terminal from making good metal-metal contact, you'll only pick up the ground connections through the threads of the ground screw, which sometimes isn't sufficient. To refresh a ground connection, I like to remove the ground screw, sand down the area around...
  view full answer...
  
• Comparing Optronics Trailer Lights MCL-83 and MCL-93
  The MCL-83 measures 17 inches long overall and 1-1/2 inches deep. It draws 0.141 amps at 12.8 volts. Light MCL-93, # MCL93RB, is 16-1/2 inches long overall and 1-5/8 inches deep. It draws 0.051 amps at 12.8 volts. Both are LED lights just with different measurements and power draw ratings.
  view full answer...
• Is Sealed, 3-Light Truck, Trailer Identification LED Light Bar Submersible
  The lights themselves on light bar # MCL93RB are sealed so water cannot get into them. This does make them submersible as well. All sealed lights are submersible but not all submersible lights are sealed. I have linked a video review of this light bar for you.
  view full answer...
• Recommendation For LED Boat Trailer Light Kit For Submersible Applications
  Sounds like you need something like the Submersible Over 80" LED Trailer Light Kit w 25' Wiring Harness, Item # TL16RK. The lights in this kit are sealed and have a waterproof construction. The LEDs are very efficient and last 50 times longer than incandescent bulbs. This kit is for trailers that are over 80 inches so if your trailer is under 80 inches then you can use a similar kit, Item # TLL9RK. Since you want something waterproof that will hold up in salt water, I recommend using...
  view full answer...
• Is the Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB Street Legal
  Yes, the Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB is rated for use as a marker/clearance light at the back of your box truck.
  view full answer...
• Trailer Light Kits With Wishbone Wiring And Full Length Ground, Running Lights and Brake/Turn Wires
  The 25 Ft 4-Way Trailer Wiring Harness # A25W2GWB is our only wiring harness with a full length ground, running light and brake/turn signal wire to run down both sides of the trailer. While we do not have this in a kit you will simply need to select the additional lights you will need. For a trailer under 80" wide you will need the following parts. Driver's Side Tail Light # STL9RB qty 1 Passenger's Side Tail Light # STL8RB qty 1 Trailer License Plate Mount Bracket # LP10SB qty 1 Side...
  view full answer...
• Plug-n-Play Tail Light or Light Bar for Towing
  We have the Heavy Duty Magnetic Tow Lights # TL21RK from Optronics that already uses a 4-Way wiring harness. All you have to do is string the excess wiring over the vehicle that you are pulling and plug the 4-Way from the Magnetic Tow Lights it into the 4-Way at the rear of your tow vehicle. If you are looking for a Light Bar, I recommend going with the Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB. You will have to splice this into your current wiring, and this...
  view full answer...
• Wire Gauge of Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB
  The wire gauge of the Sealed, 3-Light Truck, Trailer Identification LED Light Bar # MCL93RB that you referenced is 16 gauge.
  view full answer...
• Recommended Trailer Light Kit for a Boat Trailer
  Sounds like you are describing the LED Trailer Light Kit w 25' Wiring Harness # TL16RK. This is a great kit from a great company. Optronics electrical products, including this kit, have received great customer reviews! The only thing that I would change when installing this kit is the quick-splice connectors. Since this will be on a boat trailer that is submerged under water the Deka Heat Shrink Butt Connector # DW05744-10 will hold up much better and do an excellent job at keeping the...
  view full answer...
• Recommended LED Light Bar For The Back of An Enclosed Trailer
  The LED light bar strip I recommend is # MCL93RB. Each strip has 3 LED lights on the base. They are sealed, waterproof and corrosion resistant. Contains both lead wire and ground wire for mounting to all surfaces. The LED light bar strip # MCL93RB is a two wire system meaning you will have one wire with a ring terminal for your ground, and a 50-inch power lead wire. You will connect the white wire to your ground and the brown power wire lead to your power supply.
  view full answer...
• Needing Lamp Setup for Ice Fishing Shack on Trailer
  I don't offer a kit that would include everything you mention, but I can suggest a kit to use as a starting point plus the additional lamps to complete your setup. I'd begin with the Optronics Aero Pro LED light kit, part # TL16RK. This provides the wiring harness, two LED taillights as well as two clearance/marker lights. To get the trailer set up the way you're wanting, you'd need an additional 4 of the # MCL-91AK lamps and a # MCL93RB 3-lamp identification bar. These lamps are all...
  view full answer...
• Recommended Utility Trailer ID Light Bar
  We have what you are after. I have linked the selection we have available. The most common is the LED Identification Light Bar for Trailers part # MCL93RB. This will install to the existing wires you have. I recommend using Heat Shrink Connectors like part # DW05744-5.
  view full answer...
• Diameter of Mounting Holes in Optronics MCL93RB LED Identification Light Bar
  The mounting holes for the # MCL93RB ID Light Bar are 3/16 inches in diameter, I'd recommend using 3/16 inch stainless hardware and a 7/16 hole in the trailer frame. Stainless bolts, nuts and washers should be readily available at your local hardware store. If you click the provided link, you can see a product demonstration video for the # MCL93RB Light Bar.
  view full answer...
• Converting Trailer Light Bar from Incandescent to LED Lights
  The code SAE P2 91 DOT on the light lens is the lens rating, not a part number, so it is difficult to go by that number. Often the actual part number for a light will be on the back of the light base or housing. If not, it is usually easiest to go by the dimensions of the light when choosing a replacement like the LED-type # AL191RB. We do offer complete 3-light LED light bars, such as parts # MCL93RB and # MCL97RB, which appear on the linked page with other trailer clearance lights. You...
  view full answer...
• Submersible Light Bar Recommendation for Trailer Lighting
  I have a solution for you, but the Peterson Lightbar part # 136-3R that you referenced is not submersible. Instead check out the # MCL93RB which is a very similar light bar that is submersible.
  view full answer...