Trailer ID Light Bar For Trailer Over 80 Inches Wide

Question

Question:

Hello, could you please advise if I also need the strip of three lights across back, as its over 80 wide? Was planning to mount rear light setup on the back of the fenders, but the licence plate will not fit. Thank you. Regards.

asked by: Elizabeth T

1

Helpful Expert Reply:

Since your trailer is over 80 inches wide, you do need the three-light ID bar, which is the following part number:

- LED Identification Light Bar for Trailers over 80" Wide # MCL93RB

expert reply by: Kyle S

1

Answer 1

Yes, we do have the complete kit with all the wires and lighting you will need to rewire and set your trailer up with new lights. We have two options depending on the amount of side marker lights you want. The first is the LED Combination Trailer…

view full answer...

Answer 2

I pulled the Optronics LED Trailer Light Kit, part #TLL16RK, from our warehouse and measured the outside dimension. I shot a little video as I measured the lights for you to check out. The outside dimensions of the lights measure approximately 8…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Trailer ID Light Bar For Trailer Over 80 Inches Wide

Product Page this Question was Asked From

Continue Researching