Availability of Trailer Taillight ID Bar that Has LEDs

Question

Question:

Title says incandescent but description lists circuits and diodes. Want to upgrade similar light bar on trailer to LED, can I just buy the 3 lights that fit this bar, what part is that?

asked by: Garrett

0

Expert Reply:

The Peterson ID bar part # 428100 is definitely an incandescent light setup but we do have a similar version that has LED lights with the part # MCL93RB like it sounds like you are looking for.

expert reply by: Jameson C

0

Answer 1

I sure can! Based on the picture you provided the correct replacement fender for your trailer is going to be the Plastic, Single-Axle Trailer Fender w/ Top and Side Steps - White - 13" to 15" #PF11X35W which will work perfectly with the…

view full answer...

Answer 2

Yes, the Optronics Mini Thin Line LED Marker/Clearance Light #AL191AB can be flush-mounted using the Optronics Flush Mount Grommet #A91GB. This PVC grommet will provide a degree of shock protection for the installed light and its rear opening allows…

view full answer...

Answer 3

In order to install the LED Trailer Clearance/Side Marker Light part #MCL55AB you will need the Flush Mount 2" Round Grommet part #A54GB and the Right Angle 2-Wire Pigtail for Optronics Trailer Lights part #A46PB. Once you have acquired these…

view full answer...

Answer 4

We do have options available for 4 wire for your trailer, but we do only have it as sold by the foot. With that said, for standard 4 wire, you will want the Deka #16-4B-1. This is the bonded 16 gauge wire used on just about anything and you will just…

view full answer...

Answer 5

You bet we do! For the LED version, you'll need part #AL91RB. The lamp can be grommet mounted using #A91GB or surface mounted using a self grounding base like #A91BB for black/ #A91CB for chrome or a standard base like part #A91BOB for black/…

view full answer...

Answer 6

I have a solution for you, but we don't have any clearance lights that would mount with the white bushing you're referring to. If you went with the #AL191AB and #AL191RB like you mentioned you would need the #A91BOB mounting plates to mount…

view full answer...

Answer 7

The Sealed, 2" Round Trailer Clearance and Side Marker Light, Flush Mount - Amber #MC53AB or the LED #MCL55AB will use the 2" Round Grommet - Flush Mount - Open Back #A54GB for installation. You will also require the wiring pigtail #A46PB…

view full answer...

Answer 8

Yes, The Thinline LED Clearance and Side Marker Light #AL91AB has 2 male connector posts on it. This waterproof trailer light functions as both a clearance light and a side marker light when properly mounted. It is 2-1/2 inches long by 1-3/16 inches…

view full answer...

Answer 9

The Optronics clearance light part #AL91RB in all of it's configurations would require a hole to be drilled for a harness like the part #A46PB to install with a grommet like the part #A91BOB. There isn't a way to mount it flush without…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Availability of Trailer Taillight ID Bar that Has LEDs

Products Featured in This Question

Continue Researching