Troubleshooting LED Identification Light Bar With Lenses Easily Knocked Off
Updated 08/12/2020 | Published 08/11/2020
Products Featured in This Question
Question:
I have one of these installed on my boat trailer, rear bottom centre as a marker light. Do you have any recommendations for protecting the lens covers from being knocked off, in particular the centre one lowest point ? I am on my second set and for the second time the centre lens cover has been knocked off. Thank you for any help or suggestions.
asked by: Wayne
Expert Reply:
The LED Identification Light Bar for Trailers over 80" Wide - Submersible - 9 Diodes - Red Lens # MCL93RB has the wiring and housing for the individual sealed lights # AL91RB to fit. The only way to help them stay in place a little better is to add silicone around the edges to just add an additional seal that will hold up to vibration and water.
An alternative option is to use the LED Identification Light for Trailers Over 80" Wide - 3 Diode - Sealed - Rectangular - Red # MCL98RB which won't have the individual lenses.
Product Page this Question was Asked From
LED Identification Light Bar for Trailers over 80" Wide - Submersible - 9 Diodes - Red Lens
- Trailer Lights
- Clearance Lights
- Marker
- Light Bar
- Surface Mount
- Submersible Lights
- LED Light
- 15-15/16L x 1-1/2W Inch
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: equalizer
- Search Results: standard equalizer trailer suspension parts
- Search Results: trailer reflective tape
- Search Results: equalizer bushings
- Search Results: trailer breakaway kit
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Shop: Premium Trailer Breakaway Kit w/ Safety Cable, Charger, LED Tester, and 5 Ah Battery - Side Load
- Q&A: Torque Specs for Attaching Leaf Springs
- Q&A: Torque Rating Requirements for Installing Leaf Springs on a 7000 lb Tandem Axle Trailer
- Shop: LED Identification Light for Trailers Over 80" Wide - 3 Diode - Sealed - Rectangular - Red
- Shop: Curt Trailer Breakaway Kit with Trickle Charger, LED Tester, and 5 Ah Lead Acid Battery - Top Load
- Shop: Trailer Wiring
- Video: Let’s Check Out the CE Smith U-Bolt Kit for Mounting Round Trailer Axles
- Video: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles: The Breakdown
- Shop: CE Smith U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts - Zinc
- Shop: U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts
- Shop: Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 7-3/4" Long - 9/16" Center Hole
- Q&A: Torque Specs When Installling 4-Leaf Double-Eye Leaf Springs on 3,500 Pound Axle
- Video: An In-Depth Look at the LED Identification Light for Trailers Over 80" Wide
- Q&A: How Would the LED Identification Light # MCL98RB Install on a Trailer
- Video: Feature Breakdown: LED Identification Light for Trailers Over 80" Wide
- Video: All You Need to Know About the UltraThin LED ID Light Bar for Trailers over 80" Wide
- Q&A: How does the Optronics LED Identification Light # MCL98RB Mount
- Q&A: Should Boat Trailer Lights Short Out When Backed Into Water
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Trailer Lights
