See what our Experts say about this Yakima Roof Rack

• Recommended Roof Rack for Using Two Hullavators on a 2024 Ford Bronco Hard Top
  Hey Tina! Not sure what roof rack setup you were using on your Jeep but I checked with Thule and they do not have one that will work with a Hullavator item # TH898 on a 2024 Bronco. To mount and use two Hullavator item # TH898 on a 2024 Ford Bronco 4 door hard top with factory raised roof rails you will need the following parts: TimberLine Towers for Yakima Crossbars item # Y33TR 70" Long - Yakima JetStream Crossbars - Aluminum - Black item # Y00427 The 70" bars are the next size up...
  view full answer...
• How to Carry SUP and SkyBox 21 on Roof of 2006 Land Rover LR3
  Could you let me know if your Land Rover LR3 has factory installed tracks that run from the front to back or if the OEM roof rack is more of a raised type? I tried doing some research but was having trouble finding anything that looked like it was an actually OEM roof rack. If you could send me some pictures of your roof rack system that would help me know what you have.
  view full answer...
  
• Will I Be Able to Use the Thule Hullavator in the Channels of Rhino-Rack Vortex Aero Crossbars?
  To address your question - yes. The top channels in the Vortex Aero Crossbars in the # Y02-490B are the same dimensions as the Thule channels like in the Thule WingBar Evo Crossbars # TH711420. However, when it comes to finding the fit required for the Thule Hullavator # TH898 on a camper shell, it is a bit complicated. The reason why is because in order for the Hullavator to function in the "down" position, it requires at least 4 inches of crossbar clearance past the feet. In addition...
  view full answer...
• Roof Rack And Bed Cover Recommendation For 2024 Ram 2500 Big Horn Crew Cab
  Hello Nancy, thanks for reaching out. We do have roof rack options for your 2024 Ram 2500 big horn crew cab, but sadly we do not have a fit for the Thule wingbars, so you will need to go with something different. For that I recommend going with a Yakima JetStream roof rack. The JetStream aero bars will work great with your Hullavator so here is what I recommend: - BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 # Y28TR - BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers...
  view full answer...
• Low Profile Roof Rack and Cargo Box to Carry Skis on a 2018 Subaru Outback Wagon
  I went out to our warehouse to measure a lot of the kits available to you. Since the sizing is standardized and your 2018 Subaru Outback Wagon has fixed mounting points, you can predict the size of the rack overall pretty easily. The lowest profile kit is the Yakima JetStream, standing at 4-1/2 inches tall. You will need the same mounting kit regardless of what length bar, which consists of: - Yakima SkyLine Towers, part # Y53TR - Yakima LandingPad 15, part # Y00241 What's nice is...
  view full answer...
• Easily Loading and Carrying 2 Kayaks on a 2017 GMC Denali XL
  A roof rack is required first and if you are looking to ease the loading, a lift assist would be important too. The Yukon XL roof weight limit is 150 pounds so that is important in selecting rails, loading 2 kayaks, and their carriers. Yakima makes a solid roof rack option with their 66" roof rack system including parts # Y00410, # Y53TR, # Y03536, # Y00243 A side loading kayak carrier such as the Thule Hullavator # TH898 would help you a great deal loading kayaks. The video below...
  view full answer...
• Which Size Crossbars for Thule Hullavator Pro on 2026 Ford F-350
  Hi Tom! I just got to this one so I'm guessing you're going with the Thule Hullavator Pro # TH898 for your setup. I don't have the exact measurement for the 60" bars but it looks like it is too close to call. It will be 4-8" on the top. The 70" bar setup would be best, and it won't be too wide for your truck. Once again you will need the following: -BaseLine Towers for Yakima Crossbars # Y28TR -BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06185 -Yakima JetStream Crossbars...
  view full answer...
• Roof Rack Options For Carrying The Thule Hullavator On A 2022 Chevy Tahoe
  Hi Kristen! The Thule Hullavator requires anywhere from 4 to 8 inches of overhang past the tower to make sure it will not come in contact with your 2022 Chevy Tahoe. You didn't mention if you were going to running just one or one on each side, so that is definitely something to take into account. That said, these are going to be your two best options: Aero Bar Option: Yakima JetStream Crossbars - Aluminum - Black - 70" Long - Qty 2 # Y00427 SightLine Towers for Yakima Crossbars - Flush...
  view full answer...
• Will 70 Inch Yakima JetStream Crossbar Allow SUPDawn & Sky Box 16 to Fit Together
  Hi CM, So in order to fit both the Yakima SkyBox 16 # Y95AV and Yakima SUPDawg # Y04075 next to each other on crossbars, you're going to need the 70 inch long Yakima JetStream Crossbars # Y00427. Even positioned at the outermost edges of the 60 inch long bars there won't be enough space, so you'll need the 70 inch bars and there is still going to be some overhang off the side due to the widths of the cargo box and carrier.
  view full answer...
• T- Slot Rack Options For a RetraxONE XR Tonneau Cover on a 2023 Nissan Frontier With 5' Bed
  We have several racks which will fit your RetraxONE XR T-60731 on your 2023 Nissan Frontier Pro with a 5' Bed. First is the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack # Y01151-5855 which has the full height of a ladder rack and best for carrying items that will need to stick over your roof. We also have the shorter Yakima OutPost HD Overland Truck Bed Rack # Y01152-5855. And finally we have the crossbar style rack which consists of the Yakima JetStream Crossbars # Y00427, Towers...
  view full answer...
• Converting RetraxONE MX Tonneau Cover on a 2021 Ford F-150 5-1/2' Bed To Add Crossbars Above Bed
  I have a couple options for your Carolyn. The first is to replace your current side rails with the XR Rails # RTT-82381 on the Cover # RTX37VR so you will have the T-Slots. Other wise using a reack like the Adarac # A54KG would be an option as this places the rails about half way up your window and attaches to the stake bed pockets. If you go the route of the T-Slots you will want the Yakima Crossbars # Y00427, Towers # Y53TR and 2 sets of the Landing Pads # Y00221. For your keys you...
  view full answer...
• Will the Truck Hero Elevate Rack System Work With Yakima Roof Rack
  Yes, the TS (T-Slot) Rails for Truck Hero Elevate Rack System part # TH85FR is a universal track system that works with most inside the bed rail mounted tonneau covers. The tracks will then accept pretty much any track mounted accessory. In order to add a Yakima system you would need the following: SkyLine Towers for Yakima Crossbars part # Y53TR Landing Pad 1 for Yakima Control Towers part # Y00221 (2) Yakima JetStream Crossbars part # Y00427
  view full answer...
• 2019 Ram 1500 Fitment for Yakima HD Tracks and Tonneau Cover
  As long as you can fit the 2" wide Yakima 60" HD Tracks # Y74MR so you have no less than 1/8" overhanging the outside of your truck bed side (see attached) you're good to go. This then allows you to use 2 sets of the Landing Pad 26 # Y75ZR and SkyLine Towers # Y53TR for a base system. The 66" Round Crossbars # Y00410 might work but I'm not sure if you'll have the clearance for that since I'm not sure where the Yakima tracks will sit. If they truly can sit in the middle of your rails...
  view full answer...
  
• Recommended Crossbars for Yakima Top Tracks On an A.R.E Camper Shell CX Series
  The Thule TracRac CapRac Ladder Rack for Camper Shell/Truck Cap # TH29200XT is not actually meant to be installed into top tracks. This crossbar system is actually meant to be installed in fixed points on your camper shell so it's not going to work with your Yakima tracks. Yakima does offer a complete system - # Y47CV which includes everything, but since you already have the tracks you'd just need the crossbars # Y00427, the landing pad # Y00221, and the towers # Y53TR. These bars and...
  view full answer...
• Are Rhino-Rack and Yakima Lock Cores Interchangeable for a 2013 Ram 2500
  The Rhino-Rack key and lock systems are not interchangeable with the Yakima SKS lock systems. I noticed you are looking at # Y02-500B which mounts in tracks. The tracks would have to be installed by drilling into the vehicle roof. If you want to avoid that and still have a Yakima rack you can look at other roof rack options for your 2013 Ram 2500. Provided that the truck has the Crew Cab you can use the following Yakima roof rack parts: JetStream Bars # Y00427 or CoreBars # Y00423 BaseLine...
  view full answer...
• Recommended Thule Aero Style Bar for Lengths Longer than 60 Inch WingBar Evo for Subaru Outback
  Thule WingBar Evo Crossbars do not come in lengths beyond 60 inches. To get longer bars that are compatible with your Thule feet you will need to use their ProBar. The Thule ProBar Evo Crossbars - Aluminum - 69" Long - Qty 2 # TH713600 can be cut to your custom length as the channels run the entire length of the bars. They still have an aero style with a top channel but they also have a rear channel and bottom channel that span the entire length to give you more mounting options. These...
  view full answer...
  
• Parts Needed to Install the PlusNut Hardware for Yakima Roof Racks on a Fiberglass Roof
  The Replacement PlusNut Hardware Kit for Yakima Roof Rack Tracks # Y8880039 is the replacement hardware for the Yakima 42" Tracks for Roof Racks # Y01126 or the Yakima 54" Tracks for Roof Racks # Y01127 both these tracks include the PlusNut hardware. Since you have a fiberglass roof you will also need to get the Replacement Capnuts, Washers and Bolts # Y8810155 which is needed when installing on a fiberglass roof. To have a complete roof rack you would also need to pick up the Landing...
  view full answer...
• How To Install Yakima LockNLoad Over Truck Bed with Tonneau Cover
  In order to install the Yakima LockNLoad Platform Roof Tray above a tonneau cover on a truck bed you will need to install a set of tracks alongside the bed rails along with a crossbar system. The crossbar system is needed because the tray is not wide enough to reach just the mounting feet on the tracks. I have attached the needed parts below: Yakima JetStream Crossbars part # Y00427 Yakima Tracks for Roof Racks part # Y01135 Landing Pad Yakima Control Towers part # Y00221 (2) SkyLine Towers...
  view full answer...
• Will Rhino-Rack Crossbars Fit On Yakima BaseLine Towers?
  The top channel on most crossbars like the Rhino-Rack and Yakima are similar but you should never mix and match towers and crossbars between different manufacturers. Their components are designed to work specifically with each other and your Yakima towers may not work properly with the Rhino-Rack crossbars. Instead you will want to stay with the Yakima crossbars from the list below to ensure they fit together properly and you have a manufacturer who will stand behind the warranty for the...
  view full answer...
• Parts Needed To Mount Rhino Rack Awning RR33200 To Yakima SkyLine Towers
  Yes, I definitely recommend getting new crossbars with a top channel. The good news is you can use the feet you already have. It appears you have the Yakima SkyLine Towers # Y53TR. So the 70" Jetstream bars # Y00427 will be all you need to mount your Rhino Rack # RR33200 awning.
  view full answer...
  
• Why are the Malone SteelTop # MPG203 Not Confirmed to Fit My 2020 Toyota 4Runner with Raised Rails?
  I have a fitment answer for you. The reason why the Malone SteelTop Roof Rack - Square Crossbars - Raised, Factory Side Rails - Steel - 65" Long # MPG203 is not listed as a confirmed fit for your vehicle is because the 65" length of the crossbars are deemed far too long for your 2020 Toyota 4Runner Limited with raised factory rails. This is why the SteelTop 50" # MPG201 and SteelTop 58" # MPG202 are confirmed fits. You are right that the towers # MAL25YR will fit your vehicle. Also, another...
  view full answer...
• Yakima Towers Needed to Mount to Landing Pad 1 on Track System
  It looks like you have the Yakima Landing Pad 1 for Yakima Control Towers # Y00221 on your A.R.E. Canopy, so I recommend using the Skyline Towers for Yakima Crossbars # Y53TR. These towers will allow you to choose between the Jetstream # Y00426 (60" long) / # Y00427 (70" long), the Yakima CoreBar # Y00422 (60" long)/ # Y00423 or use Round bars like the Yakima # Y00410 with the adapter # Y03536. These towers are not compatible with square bars that you had asked about in a previous question. If...
  view full answer...
  
• Can I Mount 70-Inch JetStream Crossbars with a Hullavator and Cargo Box on My 2022 Subaru Outback?
  Technically, it is possible to do this on your 2022 Subaru Outback Wilderness. However, the only concern with this setup is that the Yakima JetStream Crossbars - 70" # Y00427 are such long crossbars that extend past the feet on your vehicle. This may not only be illegal, it can be dangerous. We do not recommend doing this setup. I attached a video that shows just how far these crossbars protrude from a similar-sized vehicle. If you were to mount the crossbars, the compatible feet would...
  view full answer...
• What Rack is Needed to Fit Two Thule Hullavators on a 2020 Ford Expedition?
  Mounting two Hullavators # TH898 requires 57 inches of crossbar length (inside of the mounting points) and a minimum of four inches on both ends outside of the feet to operate. With that being said, you will need crossbars with a minimum length of 65 inches. The Yakima JetStream crossbars 70-inches # Y00427 will do the trick. The towers you need are the TimberLine Towers for Yakima Crossbars - Raised, Factory Side Rails # Y33TR. However, I called my contact with Thule and he strongly...
  view full answer...
• Recommended Fairing for Rola Roof rack on a 2009 Honda Accord Sedan
  Yes! Out of the variety of fairings that we have to offer I recommend the 40" long Inno Fairing # INA261 because it will fit perfectly with the 38" long Rola Sport Series Roof Rack # 59757 for your 2009 Honda Accord. If you let me know what you are wanting to use the roof rack for I can make additional recommendations for you. I have also attached an installation video and a picture of this roof rack on a 2009 Accord Sedan that you can reference.
  view full answer...
  
• Roof Rack and Ski Carrier to Fit 2019 Hyundai Santa Fe with Naked Roof
  Yakima has a really great roof rack for your 2019 Hyundai Santa Fe with a naked roof with the Baseline JetStream bar rack part numbers # Y28TR, # Y06151, # Y06154, and # Y00425 (see attached picture). This will give you an extremely high quality roof rack that has aero bars which will give you minimal wind noise. Then for a ski rack we have the FatCat EVO part # Y03096 which will hold 6 skis or part # Y03095 for up to 4. I attached a review video for this carrier for you to check out as well.
  view full answer...
  
• Kayak Rack and Load Assist for a 2018 Toyota Prius Prime Without Glass Roof
  Hey, Nick! Happy to help out. The best and easiest kayak rack to use with a load assist is the Thule Hullavator Pro # TH898. One big advantage is that everything is built into the carrier itself, here are no extra parts to remove or store. Personally, I’m not a fan of other load-assist options like the Malone DownLoader # MPG114MD-351XL, since you have to store the Telos legs inside your vehicle while traveling. That’s especially inconvenient if you’re working with a smaller vehicle. I...
  view full answer...
• Recommended Roof Rack and Bike Rack for a 2016 Lexus GSF
  The best option to transport a bike with your 2016 Lexus GSF is going to be to install a roof rack and attach a bike rack. The trunk mounted ones like item # SA805BL have mixed results and won't work with cars with spoilers. It doesn't look like your Lexus has any rails so to add a roof rack you will need the following parts: Yakima JetStream Crossbars - Aluminum - Black - 50" Long - Qty 2 item # Y00425 BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip...
  view full answer...
• Which Yakima Roof Rack Fits 2022 Ford Maverick
  Hi Alvin, Nice choice going with the Yakima rack as they make really high-quality gear. As for the correct parts for your 2022 Ford Maverick, you can actually get everything combined with just one part number depending on the bars you want. You mentioned the FX, and that is a flush-style roof rack system, which means the bars only go the width of your roof with no overhang. The FX uses bars and towers that are combined, so they aren't actually separate; to go that route you'd just need...
  view full answer...
• Roof Rack With Longer Crossbars For 2023 Kia Sorento With Naked Roof
  Hello Katherine, thanks for reaching out. Yes, we do have a product that will work for you! The best option for this will be to go with a Yakima JetStream roof rack. The design of their bars and towers allows for longer than standard crossbars, so we can set you up with something longer. For the Yakima bars, a 60" crossbar will be the closest option for something longer than 56". Here are the parts you will need for the complete roof rack system: - Yakima JetStream Crossbars - Aluminum...
  view full answer...
• How Can I Tell if I have Fixed Mounting Points on My 2015 Mazda CX-5 for a Crossbar System?
  According to the specs I have, you may have fixed mounting points on those rubber strips on your 2015 Mazda CX-5. The way you can tell is if there is a small removable tab on those rails that cover the holes. I went ahead and attached a video of a 2015 Mazda CX-5 with fixed mounting points to give you perspective about what to look for. If you determine that you have fixed mounting points, I recommend the following setup: - Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 46" #...
  view full answer...
• How to Tell if Thule Hullavator Kayak Carrier Will Fit on a Tesla Model 3
  Both the current Hullavator Pro # TH898 and the older model, part 897XT that you have, require the crossbars to overhang the feet of the roof rack by 4" - 8" for their to be enough clearance to lower the carrier without making contact with any given vehicle. If you're Tesla Model 3 crossbars have a T-Slot, you still have the T-Slot mounting hardware, and the crossbars can achieve an overhang then you'll be good to go. The nice thing is that you already have this discontinued carrier so...
  view full answer...
• Will Installing Track Roof Rack System on A.R.E. Topper Void Warranty
  Installing a track system roof rack like the Yakima parts # Y01126, # Y00221, # Y8890027, and # Y00410 won't void the warranty for your pickup but from what I could find it looks like modifying your A.R.E. topper will void that warranty. Since we aren't an A.R.E. dealer I can't really confirm this, but from my research it is very likely that your warranty will be void. So you can have the track system professionally installed but that would be your choice whether you want to pursue this...
  view full answer...
  
• What is the Best 16 Cubic Foot Or More Cargo Box/Crossbars for My 2018 Nissan Murano SL?
  There are a couple options for a cargo box setup on your 2018 Nissan Murano SL with a bare roof. As far as the box, I recommend the Yakima SkyBox 16 Roof Cargo Box - 16 cu ft # Y95AV or the Yakima SkyBox 21 Rooftop Cargo Box - 21 cu ft # Y07337. The great thing about the SkyBoxes is that they include the SuperLatch system that ensures the lid is latched closed and locked. With this mechanism, the key cannot be removed unless the lid is closed properly. In addition, the SkyBoxes include...
  view full answer...
• Should Rear Bar Sit Higher Than Front Bar on Yakima Roof Rack System for 2017 Honda Pilot
  The front and rear Yakima JetStream Crossbars like # Y00426 should be level to each other on your 2017 Honda Pilot. Looking through the installation instructions for the BaseLine Towers # Y28TR and Fit Kit # Y00146 for your Honda Pilot, it does appear that the feet are positioned onto contours that are on the vehicle's roof. To compensate for this and to make sure the front and rear bars are not mounted at different heights, the pitch setting on the Yakima Feet need to be adjusted. I recommend...
  view full answer...
  
• Roof Rack Fit on 2012 Toyota Venza With Panoramic Sunroof
  There is one roof rack that is a confirmed fit for your 2012 Toyota Venza with a panoramic sunroof, though the sunroof should not be opened with the rack on. There isn't a roof rack available for your Venza that is going to allow normal use of the sunroof when the rack is on, but you can remove the rack if you like when you aren't using it in order to utilize the sunroof. The roof rack that fits your '12 Venza with a panoramic roof is an exceptionally nice one from Yakima, and consists...
  view full answer...
• Will the Thule Force XT L Fit My 2020 BMW X5?
  Yes, you will be able to fit the Thule Force XT L # TH6357B on your 2020 BMW X5's roof. Not only do you have enough roof for the required crossbar spread of 23-5/8 - 33 inches, you will also be able to mount the box to your roof and fully open your rear hatch. If you are wanting to go bigger, the Thule Force XT XL # TH6358B and XXL # TH6359B will fit as well. As far as mounting, you will need a crossbar system in order to secure the Force XT XXL to your roof. The setup you need depends...
  view full answer...
• Will a Yakima Roof Rack System Fit My 2020 Toyota Highlander LE?
  I confirmed with Yakima that mounting points that are on your bare roof of your 2020 Toyota Highlander will fit a roof rack system. After you pop off the tab that covers the mounting points, there is a screw that you will use to attach a roof rack system. I went ahead and attached a video that shows how you would attach a Yakima roof rack system on the 2020 Toyota Highlander. For the parts you need for that setup, you will need the following parts: - Yakima JetStream Crossbars - Aluminum...
  view full answer...
• Compatibility of 3 Bike Rack on 2015 Toyota Prius
  The Reese Q-Slot Platform-Style 2 Bike Rack is a fit for your 2015 Prius but has been discontinued. If you already have the rack it will work very well for you. I recommend using the included pin and clip for a secure fit in the hitch and then using a cable lock like # e98891 to secure your bikes to the rack. The 2 inch receiver only Reese Q-Slot Platform-Style 2 Bike and 4 Bike Rack PS63138 (also discontinued) was a 2 or 4 bike carrier, but would NOT work on your 2015 Toyota Prius...
  view full answer...
• Roof Rack and Board Carrier Recommendation for 2016 Toyota Prius V with Glass Roof
  For your 2016 Toyota Prius V you will need to install a roof rack to carry the boards you mentioned. Unfortunately only Yakima makes roof racks for your vehicle and they aren't exactly super cheap. So for that you would want the Yakima CoreBar part numbers # Y00425, # Y28TR, # Y06117, # Y06174. Which with that you'd be able to use the LockRack kpart # LR59FR that you referenced. This will attach to the crossbar by the top channel.
  view full answer...
• Best Roof Rack for 2020 Kia Telluride With Naked Roof and How Does It Attach
  There are two roof configurations for a 2020 Kia Telluride, bare roof and flush side rails. The roof rack system for a bare roof attaches to the door jambs via car clips whereas the system for flush side rails attaches to the flush side rails. I recommend the Yakima JetStream Crossbar System part # Y00426, part # Y28TR, part # Y06125, and part # Y06165 if you have a bare roof. The Yakima Crossbar system is best because it has a custom fit for the best overall look, aero crossbars for...
  view full answer...
• Can Yakima Roof Rack From 2000 Ford F250 Be Used On A 2025 Ford F350?
  Hello Lori, thanks for reaching out. You may be able to re use certain components from your old Yakima roof rack, but I would need to know specifically what parts you have in order to say for sure. If you have the Yakima BaseLine towers like part # Y28TR, those could be used on the 2025 F350, you would just need a new fit kit # Y06185. You might be able to re use you crossbars but again it depends what you have. Yakima recommends a 58" or 60" crossbar for the 2025 F350. If you can tell...
  view full answer...
• Recommended Roof Rack for 2013 Toyota Venza with Panoramic Glass Roof
  I do have a solution for you, however the Rhino-Rack roof rack that you referenced will not fit your 2013 Toyota Venza if it's equipped with the panoramic glass roof. None of the solutions from Rhino-Rack are compatible with the panoramic roof on your vehicle. I checked with Yakima though and they do state that their JetStream Crossbar system is compatible with the glass roof and will work great on your Venza. This roof rack consists of # Y00426 for the two 60 inch JetStream Crossbars,...
  view full answer...
• What is Needed to Attach Yakima JetStream Crossbars to 2017 Honda CR-V With Bare Roof
  Hello Zeke, So we can get your 2017 Honda CR-V set up to mount Yakima JetStream Crossbars # Y00425, though there aren't actually different options for this. Reason for that is you can't mix and match different manufacturers parts because they won't fit together. That means to put the JetStream crossbars on the bare roof of your 2017 Honda CR-V you would have to use the following parts: - BaseLine Towers for Yakima Crossbars - Naked Roofs # Y28TR - BaseClip Fit Kit # Y06188 - BaseClip...
  view full answer...
• Roof Rack And Bed Cover Recommendation For 2024 Ram 2500 Big Horn Crew Cab
  Hello Nancy, thanks for reaching out. We do have roof rack options for your 2024 Ram 2500 big horn crew cab, but sadly we do not have a fit for the Thule wingbars, so you will need to go with something different. For that I recommend going with a Yakima JetStream roof rack. The JetStream aero bars will work great with your Hullavator so here is what I recommend: - BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 # Y28TR - BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers...
  view full answer...
• Yakima Roof Rack Parts List for a 2021 Dodge Durango with a Bare Roof
  Hey Kimlee, thanks for reaching out! Yes, the 60" # Y00426 JetStream Bars, BaseLine Towers # Y28TR, and 2 sets of the BaseClip Fit Kit # Y06180 will also fit your 2021 Dodge Durango with a bare roof (lock core kit # Y07204 optional). We do ship these to Canada as well!
  view full answer...
• Roof Rack Recommendation for 2018 Toyota Camry Hybrid with Sun Roof
  For your 2018 Toyota Camry Yakima has the CoreBar roof rack with aero shaped crossbars part numbers # Y00421, # Y28TR, and # Y06192 that can be used on vehicles with sun roofs. But Yakima states to keep it closed when the rack is installed. For a carrier to carry your two kayaks we have the Thule Stacker part # TH830 then that would work well. This rack will hold the kayaks on end. See install video I attached.
  view full answer...
• Is There A Trailer Hitch Available For A 2019 Honda Civic Sedan With A Center Exhaust
  Hi Hamza, Honda Civic models with a center exhaust unfortunately prevent the installation of a trailer hitch so the only way to haul your bike(s) would be to use a trunk mounted bike rack or roof rack mounted bike rack. If you'd prefer a trunk mounted bike rack then I recommend the Yakima FullBack 2 Bike Rack # Y02634. If you want to go with a roof rack mounted back rack and don't currently have a roof rack then you'll need the following components: Yakima JetStream Crossbars # Y00425 BaseLine...
  view full answer...
• Can Yakima Roof Rack From 2000 Ford F250 Be Used On A 2025 Ford F350?
  Hello Lori, thanks for reaching out. You may be able to re use certain components from your old Yakima roof rack, but I would need to know specifically what parts you have in order to say for sure. If you have the Yakima BaseLine towers like part # Y28TR, those could be used on the 2025 F350, you would just need a new fit kit # Y06185. You might be able to re use you crossbars but again it depends what you have. Yakima recommends a 58" or 60" crossbar for the 2025 F350. If you can tell...
  view full answer...
• What Yakima Pads and Clamps do I Need for My 2019 Ford F-250 to Use My Baseline Feet?
  Hello Michael, I am glad you wrote in, the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 # Y27FR that you were looking at is for a Ford F-150. For your 2019 Ford F-250 (vehicle that was put into the fit guide) you will want to order (2) sets of the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 # Y06185. How did end up with the feet and no pads, did you take them off of an old vehicle? What do you plan on using your roof rack for?
  view full answer...
• Which Size Crossbars for Thule Hullavator Pro on 2026 Ford F-350
  Hi Tom! I just got to this one so I'm guessing you're going with the Thule Hullavator Pro # TH898 for your setup. I don't have the exact measurement for the 60" bars but it looks like it is too close to call. It will be 4-8" on the top. The 70" bar setup would be best, and it won't be too wide for your truck. Once again you will need the following: -BaseLine Towers for Yakima Crossbars # Y28TR -BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06185 -Yakima JetStream Crossbars...
  view full answer...
• Can I Reuse Yakima Q Towers for 2021 Ford F-250
  In 2016, Yakima phased out their Q-Towers and upgraded to their new BaseLine system. That means for vehicles that are model year 2016 or newer, there are no confirmed Q-clip fits for them so we need to get you a new roof rack for your 2021 Ford F-250. If you want to reuse your round bars to make a roof rack on your F-250 Crew Cab, you can do so with a new BaseLine system. That consists of BaseLine Towers # Y28TR, a RoundBar Adapter # Y03536, and BaseClip Fit Kit # Y06185.
  view full answer...
• Roof Rack Fit for 2016 Hyundai Elantra GT With Panoramic Sunroof
  I checked for you and there is a fit for a roof rack for your 2016 Hyundai Elantra GT with the panoramic glass roof (moonroof), which is from Yakima. I verified the fit with the manufacturer and roof rack consists of the following parts: - Yakima JetStream Crossbars # Y00425 Black - BaseLine Towers for Yakima Crossbars # Y28TR - BaseClip Fit Kit # Y06151 - BaseClip Fit Kit # Y06185 - Same Key System Lock Cores (Optional) # Y07204 This is going to give your '16 Elantra GT an easy to use,...
  view full answer...
• Solution for Carrying Multiple Bikes on Roof of 2021 Ford F250
  We absolutely have roof rack options for your 2021 Ford F250. Beginning with the roof rack, I'd recommend the Yakima CoreBar roof rack which would be assembled using these parts: • Yakima 70 inch CoreBar crossbars, part # Y00423 • Yakima BaseLine Towers, part # Y28TR • Yakima Vehicle-Specific fit kit, part # Y06185 With a 70 inch long crossbar, you'll be able to fit up to 5 bikes on the roof, but keep in mind that the roof rack has a 165 lb weight capacity, so unless your bikes are really...
  view full answer...
• Can 70 Inch Yakima JetStream Crossbars be Cut on 2021 Ford F-350 Crew Cab
  We have a similar option for you, but you do not want to cut or trim down the Yakima JetStream Crossbars # Y00427. Instead, there are different Yakima bars that are designed to be cut down if needed, called CoreBars. The 70 inch CoreBars, and rest of the parts needed for a Yakima roof rack on your 2021 Ford F-350 Crew Cab are the following: - Yakima CoreBar Crossbars # Y00423 - BaseLine Towers for Yakima Crossbars # Y28TR - BaseClip Fit Kit # Y06185 I do recommend considering locks...
  view full answer...
• Can Two Thule Hullavator Kayak Carriers Be Used On A Thule TracRac SR Ladder Rack
  Yes, you can use two of the Thule Hullavator Pro Kayak Roof Rack and Lift Assist # TH898 on the Thule TracRac SR. It has plenty of capacity and space for both to fit, you'll just need to place the towers so that the crossbars are spaced 24" apart. For your 2022 Ford F-250 with a 6-3/4' bed you'll need part # TH43003XT-785 for the TracRac. The Thule Hullavator requires that the roof of the vehicle can hold at least 130lbs, but you'll be splitting this with the ladder rack. I'd just check...
  view full answer...
• Recommended Yakima Roof Rack for a 2024 Ford F-250 Crew Cab
  To add a Yakima roof rack to your 2024 Ford F-250 Crew Cab you will need the following parts: Yakima JetStream Crossbars - Aluminum - Black - 60" Long - Qty 2 item # Y00426 BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 4 item # Y06185
  view full answer...
• Roof Rack Recommendatio nfor 2018 Ford F-250 Crew Cab that is Leased
  For your 2018 Ford F-250 Crew Cab the Yakima Roof Rack part numbers # Y00422, # Y28TR, and # Y06185 would be a great solution as it is a confirmed fit and the fact that it does not permanently modify the roof of the vehicle it is installed on. So you'd be able to take the roof off when it's time to return the lease and no one would know the difference. The aero shape of these bars also helps cut down on wind noise which is a nice feature as well. I attached an install video for thist...
  view full answer...
  
• Is There a Solution for a Roof Rack on My 2021 Ford F-250 that Doesnt Require Drilling?
  I have a great no-drilling solution for you. While the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells - Track Mount - Black - 59" Long # Y01-130B requires drilling, there are options for your 2021 Ford F-250 Super Duty crew cab that do not require any drilling. To go this route, you will need the following parts: - Round 66" CrossBars for Yakima Roof Rack System (QTY 2) # Y00410 - BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 # Y28TR - RoundBar SL Adapter for Yakima...
  view full answer...
• Buying a Single Yakima HD Crossbar for a 2020 Ford F-250
  While we do not have a full kit for just one crossbar for your 2020 Ford F-250, I have compiled a list of the individual part numbers that make up the Yakima HD crossbars that are compatible with the SuperCab and CrewCab. For the crossbar itself, use part # Y95FR. It's the single bar, 60" long like the full kit. For the BaseLine Towers, use part # Y62TR. There are 2 in this kit. For the HD Bar SL Adapter, use part # Y03541. This, unfortunately, does not come in a quantity of 2, so you'll...
  view full answer...
• Half Roof Rack and Ladder Rack that Fits 2023 Ford F-350
  To do a half roof rack for the roof of your 2023 Ford F-350 you'd need the following: Yakima JetStream Crossbar part # 8880650 BaseLine Towers for Yakima Crossbars part # Y62TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers part # Y06185 There isn't a way to do a half ladder rack so best option would be an adjustable height rack like the Yakima Overhaul # Y01151-5855 so that you can have it match the height of your roof rack and if needed you could leave off the rear (or front)...
  view full answer...
• Recommended Roof Rack and Kayak Carrier for a 2003 Toyota RAV4
  Lucky for you, Yakima does make a set of crossbars that are designed to work with vehicle's that have a bare roof like your RAV4. Check out the Yakima BaseLine FX Roof Rack for Naked Roofs # Y59UV with the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06185. These crossbars measure 44 3/4" long, has a 165 lb dynamic weight capacity, and has an integrated top channel for roof mounted accessories. Since you also are looking for a way to transport some kayaks, I'd recommend checking...
  view full answer...
• Availability of Yakima JetStream Roof Rack With 70" Bars for 2026 Ford F-350 Crew Cab
  Hey Tom! We don't have a kit but we can put one together here. For a complete rack you will need the following: -BaseLine Towers for Yakima Crossbars # Y28TR -BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06185 -Yakima JetStream Crossbars - Aluminum - Black - 70" Long - Qty 2 # Y00427 Are you still thinking about adding the MOS UpLift or are you going to go a different route with your setup?
  view full answer...
• Roof Rack for Roof Tent on a 2019 Ford F-450 Super Duty Crew Cab
  While there are no roof racks that have a weight capacity of 400 lbs, I still believe we have a solution for your 2019 Ford F-450 Super Duty Crew Cab with the Yakima HD roof rack. This consists of the HD Crossbars # Y01157, BaseLine Towers # Y28TR, HD Bar SL Adapter # Y03541, and Fit Kit # Y06185. If you are looking to use a tent that has a 400 lb weight capacity like the Yakima SkyRise HD # Y07436 then you actually just need to make sure that the roof rack is rated for 165 lbs like the...
  view full answer...
• How To Transfer Crossbars From a 2019 Ford F-350 to a Leer 100RC Topper
  The track systems are all pretty much universal so you can use Yakima accessories in Thule tracks or vice versa. In regards to weight, you will be limited to 165 lbs per set of crossbars no matter which system you choose as that is all the mounting feet can handle, even with the Yakima HD Crossbars System. The vehicle's roof would likely not be able to handle much more than this either. However, you can carry up to 330 lbs total but you would need to distribute the weight so that 165 lbs...
  view full answer...
• Correct Yakima Roof Rack For 2018 Ford F-250 Crew Cab
  Okay, we can get your 2018 Ford F-250 Crew Cab set up with the right Yakima roof rack, and let's start with your first question about the correct length bars. That is determined by the manufacturer when they test fit roof racks, which is how we know the correct length of crossbar for your truck are the 70 inch long bars. In regards to a disadvantage with the clips/clamp-on versus drilled on racks, there is no disadvantage at all. Really, the only reason someone might use a rack that that...
  view full answer...
• Adding A Roof Rack To A 2020 Ford F-350 Crew Cab For Additional Cargo Carrying Capacity
  Yakima OverHaul HD Adjustable Truck Bed Ladder Rack - Aluminum - 500lbs - 68" Crossbars # Y01151-58 has an on-road capacity of 500lbs, off-road capacity of 300lbs, and static capacity of 800lbs. The correct roof rack for your 2020 Ford F-350 Super Duty Roof Rack by Yakima would be the following parts: Yakima HD Crossbars - Aluminum - Black - 60" Long - Qty 2 # Y01157. BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 # Y28TR. HD Bar SL Adapter for Yakima BaseLine, SkyLine, TimberLine,...
  view full answer...
• Are Yakima Jetstream Roof Rack Instructions for 2023 Ford F-350 Same as 2024 Models
  The Yakima JetStream roof rack part numbers # Y00426, # Y28TR, # Y06185 that fits the 2024 Ford F-350 crew cab is the same as the 2023 models so the instructions are the exact same. So Jack, what that means is that the instructions were printed when the 23' model was the newest but it's definitely the same as the 24' models.
  view full answer...
• Yakima BaseClips Y06185 Needed
  You need the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2, part # Y06185.
  view full answer...
• Parts Needed to Install Yakima JetStream Crossbars on 2021 Ford F-250
  To install 60 inch Yakima JetStream # Y00427 aero-style crossbars on your Ford F-250, you'll need the # Y28TR BaseLine towers and the # Y06185 vehicle-specific fit kit.
  view full answer...
• Roof Rack for 2020 Ford F-350 Super Duty to Carry Bike Racks
  For a roof rack for your 2020 Ford F-350 Super Duty that would allow you to carry a lot of bikes you'd want to go with a rack that has a longer crossbar like our Yakima Jetstream Rack # Y00426, # Y28TR, and # Y06185 which is 60 inches long. Then you could use a roof bike rack like the Yakima HighRoad part # Y02114 which allows you to keep the front wheel installed on the bike. Space-wise you wouldn't be limited on how many bikes you could carry as most likely you'd run out of roof capacity...
  view full answer...
• Recommended Roof Rack for a 2018 Ford F-350 Super Duty With a Naked Roof
  For your 2018 Ford F-350 super duty with a naked roof, I recommend going with the Yakima BaseLine FX Roof Rack for Naked Roofs - JetStream Aero Crossbars # Y56UV with the fit kit # Y06185. This roof rack system will work great with your naked roof, has a maximum weight capacity of 165-lbs, and has integrated t-slots so you can use roof mounted accessories as well.
  view full answer...
• Can Yakima Roof Rack From 2000 Ford F250 Be Used On A 2025 Ford F350?
  Hello Lori, thanks for reaching out. You may be able to re use certain components from your old Yakima roof rack, but I would need to know specifically what parts you have in order to say for sure. If you have the Yakima BaseLine towers like part # Y28TR, those could be used on the 2025 F350, you would just need a new fit kit # Y06185. You might be able to re use you crossbars but again it depends what you have. Yakima recommends a 58" or 60" crossbar for the 2025 F350. If you can tell...
  view full answer...
• What Yakima Pads and Clamps do I Need for My 2019 Ford F-250 to Use My Baseline Feet?
  Hello Michael, I am glad you wrote in, the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 # Y27FR that you were looking at is for a Ford F-150. For your 2019 Ford F-250 (vehicle that was put into the fit guide) you will want to order (2) sets of the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2 # Y06185. How did end up with the feet and no pads, did you take them off of an old vehicle? What do you plan on using your roof rack for?
  view full answer...
• Which Size Crossbars for Thule Hullavator Pro on 2026 Ford F-350
  Hi Tom! I just got to this one so I'm guessing you're going with the Thule Hullavator Pro # TH898 for your setup. I don't have the exact measurement for the 60" bars but it looks like it is too close to call. It will be 4-8" on the top. The 70" bar setup would be best, and it won't be too wide for your truck. Once again you will need the following: -BaseLine Towers for Yakima Crossbars # Y28TR -BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06185 -Yakima JetStream Crossbars...
  view full answer...
• Can I Reuse Yakima Q Towers for 2021 Ford F-250
  In 2016, Yakima phased out their Q-Towers and upgraded to their new BaseLine system. That means for vehicles that are model year 2016 or newer, there are no confirmed Q-clip fits for them so we need to get you a new roof rack for your 2021 Ford F-250. If you want to reuse your round bars to make a roof rack on your F-250 Crew Cab, you can do so with a new BaseLine system. That consists of BaseLine Towers # Y28TR, a RoundBar Adapter # Y03536, and BaseClip Fit Kit # Y06185.
  view full answer...
• Roof Rack Fit for 2016 Hyundai Elantra GT With Panoramic Sunroof
  I checked for you and there is a fit for a roof rack for your 2016 Hyundai Elantra GT with the panoramic glass roof (moonroof), which is from Yakima. I verified the fit with the manufacturer and roof rack consists of the following parts: - Yakima JetStream Crossbars # Y00425 Black - BaseLine Towers for Yakima Crossbars # Y28TR - BaseClip Fit Kit # Y06151 - BaseClip Fit Kit # Y06185 - Same Key System Lock Cores (Optional) # Y07204 This is going to give your '16 Elantra GT an easy to use,...
  view full answer...
• Solution for Carrying Multiple Bikes on Roof of 2021 Ford F250
  We absolutely have roof rack options for your 2021 Ford F250. Beginning with the roof rack, I'd recommend the Yakima CoreBar roof rack which would be assembled using these parts: • Yakima 70 inch CoreBar crossbars, part # Y00423 • Yakima BaseLine Towers, part # Y28TR • Yakima Vehicle-Specific fit kit, part # Y06185 With a 70 inch long crossbar, you'll be able to fit up to 5 bikes on the roof, but keep in mind that the roof rack has a 165 lb weight capacity, so unless your bikes are really...
  view full answer...
• Can 70 Inch Yakima JetStream Crossbars be Cut on 2021 Ford F-350 Crew Cab
  We have a similar option for you, but you do not want to cut or trim down the Yakima JetStream Crossbars # Y00427. Instead, there are different Yakima bars that are designed to be cut down if needed, called CoreBars. The 70 inch CoreBars, and rest of the parts needed for a Yakima roof rack on your 2021 Ford F-350 Crew Cab are the following: - Yakima CoreBar Crossbars # Y00423 - BaseLine Towers for Yakima Crossbars # Y28TR - BaseClip Fit Kit # Y06185 I do recommend considering locks...
  view full answer...
• Can Two Thule Hullavator Kayak Carriers Be Used On A Thule TracRac SR Ladder Rack
  Yes, you can use two of the Thule Hullavator Pro Kayak Roof Rack and Lift Assist # TH898 on the Thule TracRac SR. It has plenty of capacity and space for both to fit, you'll just need to place the towers so that the crossbars are spaced 24" apart. For your 2022 Ford F-250 with a 6-3/4' bed you'll need part # TH43003XT-785 for the TracRac. The Thule Hullavator requires that the roof of the vehicle can hold at least 130lbs, but you'll be splitting this with the ladder rack. I'd just check...
  view full answer...
• Recommended Yakima Roof Rack for a 2024 Ford F-250 Crew Cab
  To add a Yakima roof rack to your 2024 Ford F-250 Crew Cab you will need the following parts: Yakima JetStream Crossbars - Aluminum - Black - 60" Long - Qty 2 item # Y00426 BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 item # Y28TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 4 item # Y06185
  view full answer...
• Roof Rack Recommendatio nfor 2018 Ford F-250 Crew Cab that is Leased
  For your 2018 Ford F-250 Crew Cab the Yakima Roof Rack part numbers # Y00422, # Y28TR, and # Y06185 would be a great solution as it is a confirmed fit and the fact that it does not permanently modify the roof of the vehicle it is installed on. So you'd be able to take the roof off when it's time to return the lease and no one would know the difference. The aero shape of these bars also helps cut down on wind noise which is a nice feature as well. I attached an install video for thist...
  view full answer...
  
• Is There a Solution for a Roof Rack on My 2021 Ford F-250 that Doesnt Require Drilling?
  I have a great no-drilling solution for you. While the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells - Track Mount - Black - 59" Long # Y01-130B requires drilling, there are options for your 2021 Ford F-250 Super Duty crew cab that do not require any drilling. To go this route, you will need the following parts: - Round 66" CrossBars for Yakima Roof Rack System (QTY 2) # Y00410 - BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 # Y28TR - RoundBar SL Adapter for Yakima...
  view full answer...
• Buying a Single Yakima HD Crossbar for a 2020 Ford F-250
  While we do not have a full kit for just one crossbar for your 2020 Ford F-250, I have compiled a list of the individual part numbers that make up the Yakima HD crossbars that are compatible with the SuperCab and CrewCab. For the crossbar itself, use part # Y95FR. It's the single bar, 60" long like the full kit. For the BaseLine Towers, use part # Y62TR. There are 2 in this kit. For the HD Bar SL Adapter, use part # Y03541. This, unfortunately, does not come in a quantity of 2, so you'll...
  view full answer...
• Half Roof Rack and Ladder Rack that Fits 2023 Ford F-350
  To do a half roof rack for the roof of your 2023 Ford F-350 you'd need the following: Yakima JetStream Crossbar part # 8880650 BaseLine Towers for Yakima Crossbars part # Y62TR BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers part # Y06185 There isn't a way to do a half ladder rack so best option would be an adjustable height rack like the Yakima Overhaul # Y01151-5855 so that you can have it match the height of your roof rack and if needed you could leave off the rear (or front)...
  view full answer...
• Recommended Roof Rack and Kayak Carrier for a 2003 Toyota RAV4
  Lucky for you, Yakima does make a set of crossbars that are designed to work with vehicle's that have a bare roof like your RAV4. Check out the Yakima BaseLine FX Roof Rack for Naked Roofs # Y59UV with the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06185. These crossbars measure 44 3/4" long, has a 165 lb dynamic weight capacity, and has an integrated top channel for roof mounted accessories. Since you also are looking for a way to transport some kayaks, I'd recommend checking...
  view full answer...
• Availability of Yakima JetStream Roof Rack With 70" Bars for 2026 Ford F-350 Crew Cab
  Hey Tom! We don't have a kit but we can put one together here. For a complete rack you will need the following: -BaseLine Towers for Yakima Crossbars # Y28TR -BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06185 -Yakima JetStream Crossbars - Aluminum - Black - 70" Long - Qty 2 # Y00427 Are you still thinking about adding the MOS UpLift or are you going to go a different route with your setup?
  view full answer...
• Roof Rack for Roof Tent on a 2019 Ford F-450 Super Duty Crew Cab
  While there are no roof racks that have a weight capacity of 400 lbs, I still believe we have a solution for your 2019 Ford F-450 Super Duty Crew Cab with the Yakima HD roof rack. This consists of the HD Crossbars # Y01157, BaseLine Towers # Y28TR, HD Bar SL Adapter # Y03541, and Fit Kit # Y06185. If you are looking to use a tent that has a 400 lb weight capacity like the Yakima SkyRise HD # Y07436 then you actually just need to make sure that the roof rack is rated for 165 lbs like the...
  view full answer...
• How To Transfer Crossbars From a 2019 Ford F-350 to a Leer 100RC Topper
  The track systems are all pretty much universal so you can use Yakima accessories in Thule tracks or vice versa. In regards to weight, you will be limited to 165 lbs per set of crossbars no matter which system you choose as that is all the mounting feet can handle, even with the Yakima HD Crossbars System. The vehicle's roof would likely not be able to handle much more than this either. However, you can carry up to 330 lbs total but you would need to distribute the weight so that 165 lbs...
  view full answer...
• Correct Yakima Roof Rack For 2018 Ford F-250 Crew Cab
  Okay, we can get your 2018 Ford F-250 Crew Cab set up with the right Yakima roof rack, and let's start with your first question about the correct length bars. That is determined by the manufacturer when they test fit roof racks, which is how we know the correct length of crossbar for your truck are the 70 inch long bars. In regards to a disadvantage with the clips/clamp-on versus drilled on racks, there is no disadvantage at all. Really, the only reason someone might use a rack that that...
  view full answer...
• Adding A Roof Rack To A 2020 Ford F-350 Crew Cab For Additional Cargo Carrying Capacity
  Yakima OverHaul HD Adjustable Truck Bed Ladder Rack - Aluminum - 500lbs - 68" Crossbars # Y01151-58 has an on-road capacity of 500lbs, off-road capacity of 300lbs, and static capacity of 800lbs. The correct roof rack for your 2020 Ford F-350 Super Duty Roof Rack by Yakima would be the following parts: Yakima HD Crossbars - Aluminum - Black - 60" Long - Qty 2 # Y01157. BaseLine Towers for Yakima Crossbars - Naked Roofs - Qty 4 # Y28TR. HD Bar SL Adapter for Yakima BaseLine, SkyLine, TimberLine,...
  view full answer...
• Are Yakima Jetstream Roof Rack Instructions for 2023 Ford F-350 Same as 2024 Models
  The Yakima JetStream roof rack part numbers # Y00426, # Y28TR, # Y06185 that fits the 2024 Ford F-350 crew cab is the same as the 2023 models so the instructions are the exact same. So Jack, what that means is that the instructions were printed when the 23' model was the newest but it's definitely the same as the 24' models.
  view full answer...
• Yakima BaseClips Y06185 Needed
  You need the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers - Qty 2, part # Y06185.
  view full answer...
• Parts Needed to Install Yakima JetStream Crossbars on 2021 Ford F-250
  To install 60 inch Yakima JetStream # Y00427 aero-style crossbars on your Ford F-250, you'll need the # Y28TR BaseLine towers and the # Y06185 vehicle-specific fit kit.
  view full answer...
• Roof Rack for 2020 Ford F-350 Super Duty to Carry Bike Racks
  For a roof rack for your 2020 Ford F-350 Super Duty that would allow you to carry a lot of bikes you'd want to go with a rack that has a longer crossbar like our Yakima Jetstream Rack # Y00426, # Y28TR, and # Y06185 which is 60 inches long. Then you could use a roof bike rack like the Yakima HighRoad part # Y02114 which allows you to keep the front wheel installed on the bike. Space-wise you wouldn't be limited on how many bikes you could carry as most likely you'd run out of roof capacity...
  view full answer...
• Recommended Roof Rack for a 2018 Ford F-350 Super Duty With a Naked Roof
  For your 2018 Ford F-350 super duty with a naked roof, I recommend going with the Yakima BaseLine FX Roof Rack for Naked Roofs - JetStream Aero Crossbars # Y56UV with the fit kit # Y06185. This roof rack system will work great with your naked roof, has a maximum weight capacity of 165-lbs, and has integrated t-slots so you can use roof mounted accessories as well.
  view full answer...
• Roof Rack for 2022 Ford F-250 Crew Cab
  Hi Devin; I'm not aware of one that attaches to the fixed points on your roof but we do have roof racks you can add to your 2022 F-250 without drilling. All of the roof racks are going to clamp on using the door jambs which also means the rack is easy to install and take off. Sticking with Yakima, you can use the Yakima BaseLine Roof Rack for Naked Roofs # Y76KB. This comes with their extremely quiet JetStream crossbars along with the feet and fit kit required for installation.
  view full answer...

Do you have a question about this Roof Rack?