To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Adapt your camper shell, hard tonneau, or hardtop resin roof to carry gear with this roof-rack system. Locking, Quick Mount legs mount to tracks. Black, Vortex Aero crossbars accommodate clamp-on and channel-mount gear.
Features:
Specs:
The bases of these Rhino Rack legs easily mount into the included Rhino-Rack RTC-style roof rack tracks with included hardware. Just slide the nuts into the tracks, line up the mounting plates, and bolt the bases down. After this initial setup, you can leave the bases in the tracks.
Molded inserts help keep out dirt and provide a finished look when there are no legs and crossbars installed. To install a leg, simply remove the insert.
Once you've set up the bases, installing and removing your roof rack is easy. The Quick Mount legs have an integrated trigger system that creates an easy, tool-free installation.
To install a leg in a base, pinch and slide the internal triggers together.
Lower the leg onto the base and slide the internal triggers apart to secure the leg in the base.
Once the leg is installed in the base, replace the cover and lock it to help secure the system to your roof.
Alternate Instructions
Average Customer Rating: 4.7 out of 5 stars (1787 Customer Reviews)
Adapt your camper shell, hard tonneau, or hardtop resin roof to carry gear with this roof-rack system. Locking, Quick Mount legs mount to tracks. Black, Vortex Aero crossbars accommodate clamp-on and channel-mount gear.Very nice rack package. Everything was complete, and install was easy 4/10. I had used another review for the hole spacing, as it was easier. Holes at each end 5/8 in then at 9, 18, 27, 36, 45, 54, for a total of 8 on each rail. I bought the heavy duty set, that’s why there’s 8. The standard has only 6/rail. I marked a centerline on the cap, and put the rails at 36” on center. I used painters tape to be sure they were straight. I also measured , and laid out the holes on the cap and drilled a SINGLE HOLE at the 36” mark. Then verified that the end holes would hit the reinforced portion of my ARE cap. Once that was verified, I drilled the rest of the holes. Because of the camber of the cap, a second person is helpful (holding the rail tight to the cap) when tightening up the nuts from inside the cap. After that, the rest was easy. Just center the rail mounts and lock them in. I would definitely recommend this rack set up, Especially since it was half of what my local Yakima dealer quoted me. This was installed on a 2016 Silverado, 2500. Tools used- Tape measure, grease pencil, painters tape, 1/4” drill bit and Cordless drill.
The final installed product is great. Install took a couple of hours. Th main slow down was the rails mounted to the roof of my truck camper were too long so I needed to cut them down to size. Also the assembly for mounting the cross bars has a lot of small screws and locks. I took my time and the final results are great.
THE GENIUS OF A PERFECT SOLUTION It is not very often that a purchase for something as mundane as a utility device stirs such awe inspired appreciation and praise. I have just completed the installation of the RLCP Rhino Heavy Duty Canopy/Hard Tonneau Track Mount atop my A.R.E. Camper Shell. I am amazed at the attention to detail of each and every part which has been carefully engineered and perfectly manufactured. I am truly impressed by the genius of a perfect solution to my roof top cargo handling needs! From the mating surfaces of the injection molded towers and the lightweight, but durable extruded anodized aluminum crossbars, to the gentle contour of the rail stock to the camper rooftop, every single part has form, fit and function! The finished product is beautiful, durable, convenient, and for the money invested, economical. I give Five Stars of Praise to the Aussie friends at Rhino-Rack Australia Pty, Ltd. Equally praiseworthy is the superb performance of e-trailers, Inc. These folks distinguish themselves from the competition through their superior attributes of website presentation, pricing, order fulfillment and package integrity. This is a unique distribution partnership which is imbued with the highest standards of e-commerce. Job well done, everyone!
Scott H - 06/30/2019Overall I’m very pleased. The rack and track components are all very high quality. Hardware too. My only complaint is that the installation instructions are not very good. 1-all the measurements are given in millimeters. Why? 2-there’s no mention in the instructions to leave the o ring off of the T bots on the ends. The t bolts on the ends have to be inserted in to the track end caps. The track end cap then becomes the seal for those holes. If you have the o rings on them too, the the track will not pull down flat on to the camper top. 3-the leg hardware needs partially assembled (screws, washers, hex nuts) and then the assembly slid on to the cross bars, then place the legs in to the mounting plates. Then fully tighten the screws. You’ll never get the screws started in to the hex nuts otherwise. 4-the vortex rubber strips are in short pieces. Why? I think they’d be better if they were one long piece. Also, when installing the tracks, I found it easier to find the center of the camper top and work from that for placement of tracks. It’s very difficult to get good accurate measurements on the curved edges of camper top.
Great product went on easily highly rec ommended
The rail kit for fiberglass truck caps arrived promptly and was as described on the website. Reasonably easy to install and easily as good as Thule and Yakima racks for half the money. My only minor quibble is a couple of small scratches on a crossbar. However, since it's sure to get scratches from normal use is not a big deal. It'll be used to mount an awning and extra gear for group camping trips.
Installed on 2014 F-150 w/ fiberglass topper. Almost downgraded kit a star because of the instructions... incomplete and some important errors... so do the math and don't trust the indicated 5-5/8" spacing for drilling the mounting holes... you'll end up w/ extra holes you'll need to go back and fill... recommend keeping it simple, two are 5/8" in from both ends, and then just mark at 9", 18", 27", 36", 45" and 54" for the other six hole, from either end. There are eight bolts for each side, but only six rubber grommets, had to presume since the two end ones go thru the rubber end cap they didn't need/get a grommet. Did it by myself; definitely recommend a second pair of hands to at least hold the other end the rail during marking, a helper would have made installation a whole lot simpler and faster. But the end results make it all worthwhile.
Very easy to install, product is stronger than anticipated. Purchased for kayak transport, very pleased.
Very happy with my roof rack. Sturdy, strong, no paint chips, no rust, no issues whatsoever!
I love the roof rack and use it often...from carrying kayaks, etc....to loading lumber. It was a great purchase and a compliment to the truck topper.
Received very fast! Unmatched customer service! Pricing on items is not always the lowest but customer service makes up for the prices.
Installed this setup on my camper shell and so far has been solid as a rock and held up to some strong winds with surfboards.
Solid design and easy to install. Only difficult part of the process is squaring the rails on a rounded roof, which doesn’t really apply to the product itself
Very impressed with this system: quality materials, nicely-designed parts that work well together, straightforward installation & assembly, plus it includes o-rings for the bolts & butyl patches to surround the drilled holes, so waterproofing has already been addressed (no need to add your own silicone or otherwise). Once the holes are drilled in the topper, the rack goes together quickly & easily. Would definitely recommend for anyone looking to add tracks & crossbars to their fiberglass cap/topper.
My product arrived promptly and in good order. I appreciate the clear written instructions provided by etrailer. More importantly, I plan to follow the step-by-step instructional video that etrailer has posted on YouTube. I have confidence that the install will go smoothly with such great support!
You guys are the absolute best!
Great product at a great price. I would recommend etrailer as the company to purchase from!
Great rack. I have never regretted the purchase. I would definitely recommend.
Excellent customer service that far exceeds expectations! I highly recommend this company, and I will return as a repeat customer whenever possible.
Easy installation on a fiberglass cap. My cap has a fairly flat even roof so it was pretty straight forward. Take your time to lay out the hole pattern and it should go fine.
excellent quality product and great fast shipping and packaging.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.