See what our Experts say about this Yakima Roof Rack

• What Roof Basket will Attach Directly to My Raised Rails on My 2022 Toyota 4Runner?
  I have a great option for you if you do not like the height of the Yakima LockNLoad # Y05045 with the Timberline Towers # Y33TR on your raised factory side rails on your 2022 Toyota 4Runner. Unfortunately, I confirmed with Yakima that you will need to have the Timberline Towers in order to attach the LockNLoad to your rails. They cannot be mounted without those towers directly to your rails. In order to complete this setup, you also need 2 sets of the LockNLoad SL Adapter for Yakima SkyLine...
  view full answer...
• Parts Needed To Mount A Yakima LockNLoad Platform On A 2024 Subaru Forester Wilderness
  Hey Jeff, There's going to be two ways to attach a Yakima LockNLoad Platform to the roof of your Forester. If mounting to crossbars you can use crossbar clamps # Y05039 (qty 2). If you decide you don't want to use the crossbars and instead use just the rails that run front-to-back then you would need TimberLine Towers # Y33TR (qty 4) and SL adapters # Y05042 (qty 2). Yakima recommends the 60" Long x 54" Wide # Y05045 for your Forester. This would require two sets of crossbar clamps...
  view full answer...
• Low Profile Roof Platform Recommendation for 2020 Toyota 4Runner with Factory Side Rails
  For your 2020 Toyota 4Runner with the factory side rails, I recommend the Yakima LockNLoad Platform Roof Tray 60" Long x 54" Wide, part # Y05045. It's pretty low profile at only 4 inches tall, and it will not interfere with your sunroof, since it will sit right behind it. I've attached a couple of photos so you can see for yourself. To attach the platform, you'll need the LockNLoad SL Adapters # Y05042-2 (qty 4), and TimberLine Towers # Y33TR (qty 4). This will add approximately another...
  view full answer...
  
• 2018 Toyota 4Runner OEM Crossbars Fitment with Yakima LockNLoad Platform Rack
  The Yakima LockNLoad Platform Rack for Crossbars # Y05047-39 will fit your 2018 Toyota 4Runner, but you'll need to use aftermarket crossbars because the OEM crossbars sit too low to the roof and this mounting hardware won't fit. To install an aftermarket roof rack I recommend the Malone AirFlow2 # MPG216 because it is a cost-effective solution that will get the job done. If you'd like a solution that looks a little more custom fit the you can use the 60" Long x 54" Wide LockNLoad Platform...
  view full answer...
• How Much Does Complete Yakima LockNLoad Platform For 2019 Chevy Suburban Weigh?
  Hello Jake, thanks for reaching out. I will go ahead and list the weight of each product you mentioned below: - Yakima Skyline Towers 4 Pack # Y53TR - 6 lbs - Yakima Landing Pad 17 4 Pack # Y00243 - 2 lbs - LockNLoad SL Adapter 4 Pack # Y05042-2 - 1.5 lbs - Yakima LockNLoad Platform 60" Long x 54" Wide # Y05045 - 57 lbs Let me know if there is anything else I can do to help
  view full answer...
• Can Yakima LockNLoad Platform Tray Attach to Thule Xsporter
  Hey Josh, yes the Yakima LockNLoad Roof Trays like the part # Y05045 can attach to the Thule Xsporter load bars as the Xsporter has top channels on top of the bars that the LockNload can attach to with the included T-bolts.
  view full answer...
• Can 2023 Subaru Outback Wilderness Use Yakima LockNLoad Platform Without Crossbars
  Hi David, Yep, you can use the LockNLoad on your 2023 Subaru Outback Wilderness without having to use crossbars. I checked directly with Yakima for you to verify this, though you will need the larger 60" x 54" platform to fit the width of your Outback. Here is exactly what you'll need: - Yakima LockNLoad Platform Roof Tray - 60" Long x 54" Wide # Y05045 - TimberLine Towers # Y33TR - LockNLoad SL Adapter - Qty 4 # Y05042-2
  view full answer...
• What is the Recommended LockNLoack Platform for My 2022 Subaru Outback Wilderness?
  For your 2022 Subaru Outback Wilderness, Yakima recommends the Yakima LockNLoad Platform Roof Tray - Aluminum - 60" Long x 54" Wide # Y05045. Since your vehicle has raised factory rails, you will need to purchase the TimberLine Towers # Y33TR along with the LockNLoad SL Adapter for Yakima SkyLine and TimberLine Towers # Y05042-2 to attach directly to the rails.
  view full answer...
• Does Yakima LockNLoad Platform Fit Rhino-Rack Vortex Aero Crossbars
  Thanks for the photo, and yes, the LockNLoad will indeed fit to Rhino-Rack Vortex aero crossbars like your Rhino-Rack Vortex Crossbars for Retrax XR # RRVA180B-RRRLT600. You'll just need adapters to mount the platform, and here are the part numbers: - Yakima LockNLoad Platform Roof Tray # Y05045 - Crossbar Clamps for Yakima LockNLoad Platform Rack # Y05039 I also wanted to note that the clamps come in a 2-pack, and you will need a total of 4 clamps, so order two of the # Y05039.
  view full answer...
  
• How To Install Yakima LockNLoad Over Truck Bed with Tonneau Cover
  In order to install the Yakima LockNLoad Platform Roof Tray above a tonneau cover on a truck bed you will need to install a set of tracks alongside the bed rails along with a crossbar system. The crossbar system is needed because the tray is not wide enough to reach just the mounting feet on the tracks. I have attached the needed parts below: Yakima JetStream Crossbars part # Y00427 Yakima Tracks for Roof Racks part # Y01135 Landing Pad Yakima Control Towers part # Y00221 (2) SkyLine Towers...
  view full answer...
• Recommended Platform Rack for a 2021 Subaru Ascent
  I did a little digging around and it looks like the roof on your 2021 Suabru Ascent is around 63 inches, making the Yakima LockNLoad Platform Roof Tray # Y05045 with the TimberLine Towers for Yakima Crossbars # Y33TR, and the LockNLoad SL Adapter for Yakima SkyLine and TimberLine Towers # Y05042-2 near perfect. This platform rack measures 60" long, 54" wide, and will be a perfect addition to your Subaru for all your camping and luggage needs. This rack also has top channels so you can...
  view full answer...
• Can Yakima LockNLoad be Installed on 2021 Toyota 4Runner OEM Roof Rack
  Great question! The OEM roof rack on your 2021 Toyota 4Runner looks nice but it sits too low to your roof for the Yakima LockNLoad # Y05045-39 mounting hardware to fit. Instead of purchasing a roof rack AND the LockNLoad what I recommend doing is picking up the parts to mount the LockNLoad directly to the raised rails on your 4Runner: 60" Long x 54" Wide LockNLoad # Y05045 SL Adapter # Y05042-2 TimberLine Towers # Y33TR We don't have any brackets designed to fit with the ARB awnings...
  view full answer...
• Will Yakima RoadShower Work With Yakima LockNLoad
  Yes, the Yakima RoadShower Portable Solar Shower part # Y29VR will work with the Yakima LockNLoad Platform Roof Trays like part # Y05045. I confirmed this with Yakima as well. There are no extra parts needed.
  view full answer...
• Rhino-Rack Pioneer Platform Rack for 2019 Ford Expedition with Factory Rails and No Crossbars
  I actually had the chance to work with a 2019 Ford Expedition. While in the shop, I tested the RhinoRack roof racks we had shown to be compatible with the factory installed rails and to my surprise, the SX Series Legs # RRSX100 were not a fit. When trying to install them, I could tell they were not tall enough to catch on the rather large and triangular shape of the Expedition rails. The only style of legs or towers that will work is the kind that wraps around the entire bar, like the...
  view full answer...
  
• Can Yakima LockNLoad Platform For 2017 Toyota Highlander XLE be Used with Roof Tent
  The Yakima LockNLoad Platform part # Y05045, # Y53TR, # Y05042-2, and # Y00242 would work great for your tent setup. This will give you a 165 lb dynamic weight capacity which is the standard capacity needed for tents which would use a static capacity instead and would be much higher. This is a creative solution to give you the additional spread you'd need for your tent too!
  view full answer...
• Largest Yakima LockNLoad Platform That Fits 2 Roof Rack Crossbars
  I checked with Yakima and the largest LockNLoad Platform Tray that will work with a roof rack system with two crossbars is the 60" Long x 54" Wide Yakima LockNLoad Platform Roof Tray # Y05045. To mount this tray to your BMW you will need the Crossbar Clamps for Yakima LockNLoad Platform # Y05039. The 84" Long x 49" Wide LockNLoad Platform # Y05047 does require at least three crossbars to mount. Using less than that would make it unstable, and not only void the warranty, but potentially...
  view full answer...
  
• Can You Use a Larger Yakima LockNLoad Platform Roof Tray on a 2023 Ford Expedition Than the 60"x54"
  You are correct that the 2023 Ford Expedition Platform Roof Rack by Yakima will fit the raised side rails on your Expedition. The 2023 Ford Expedition Platform Roof Rack by Yakima consist of: - Yakima LockNLoad Platform Roof Tray # Y05045 - TimberLine Towers for Yakima Crossbars # Y33TR - LockNLoad SL Adapter for Yakima # Y05042-2 I have an alternate option, but you would not be able to use the Yakima LockNLoad Platform Roof Tray # Y05048 (84" Long x 54" Wide) on your 2023 Ford Expedition....
  view full answer...
• How to Use the Yakima LockNLoad Platform Roof Tray On a Camper Shell
  In order to mount the Yakima LockNLoad Platform Roof Tray part # Y05045 on a truck bed camper shell I recommend using the Yakima HardTop SL Roof Rack part # Y01618 because it's a complete all around system that has everything that you need. It comes with adjustable tracks to accommodate many different roof rack accessories and aero crossbars for the best wind resistance. It's also low profile at around 4-6" tall. Unfortunately, there isn't any sort of Rhino-Rack Backbone Mounting System...
  view full answer...
• Recommended Platform Rack System without Crossbars for 2019 Toyota Highlander XLE
  For a low profile platform style rack similar to a Rhino Rack Backbone System, the only available option is the Yakima Roof Rack and Platform System that uses parts # Y05045, # Y53TR, # Y05042-2, # Y00242. This kit combines the Yakima Lock N Load Platform # Y05045 and Yakima Skyline towers # Y53TR to give you the platform without a crossbar for the low profile setup you're looking for. The additional parts are for the footpack and adapters to allow you to mount the towers to your 2019...
  view full answer...
• Roof Basket That Mounts to Factory Raised Side Raids of 2019 Jeep Renegade
  There is one! It is called the Surco Safari Rack 5.0 for Raised Factory Rails # SPS5060-1101. It's size 60" x 50" which is the size Surco recommended for your 2019 Jeep Renegade. This system is a complete basket with sides and comes with adapters that clamp straight to your factory roof rails. I attached a video below with our review and explanation of the basket. It is similar to the very popular Yakima LockNLoad Platform Rack # Y05045. The LockNLoad platform though still needs separate...
  view full answer...
• Is The Rhino Rack Stow It Utility Holder Compatible With Yakima Trays and Crossbars?
  Yes, the Stow It Utility Holder # RR95AB can be mounted in the t-slots on the Yakima LockNLoad Platform Roof Tray # Y05045. It will also work on the Yakima HD Crossbars # Y01158 as both systems are using the t-track mounting system.
  view full answer...
• Larger Roof Platform Tray that Fits 2023 Honda Pilot
  We have a larger platform tray that fits the roof of your 2023 Honda Pilot with flush side rails with the Yakima LockNLoad part # Y05045, # Y53TR, # Y05042-2, # Y00245 which will give you a platform that is 60 inch by 54 inch. There isn't a Rhino Rack option at this time that fits.
  view full answer...
• Can Yakima LockNLoad Platform for 2011 Jeep Patriot Support Yakima SkyRise Tent
  The Yakima LockNLoad Platform Roof Tray part numbers # Y05045, # Y33TR, and # Y05042-2 that fits your 2011 Jeep Patriot can be used with roof top tents like the Yakima SkyRise Tent part # Y79XR that you mentioned without requiring any additional support.
  view full answer...
• Roof Platform Tray that Fits 2015 Chevy Tahoe
  I have a way to install a roof platform tray similar to a Rhino Rack Pioneer Platform but Rhino Rack does not have a fit for your 2015 Chevy Tahoe. Instead you'd need to go with a Yakima LockNLoad with the part # Y05045, # Y53TR, # Y05042-2, # Y00243 which gives you a 60 inch by 54 inch platform confirmed as a fit.
  view full answer...
• Recommended Roof Rack For Attaching A Thule Hullavator To A 2021 Toyota Highlander
  To attach the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs # TH898 to your 2021 Toyota Highlander you'll need a roof rack that has a T-Slot in the crossbars for the Hullavator to slide into. Currently the only brand of roof racks we carry for your vehicle that are compatible with your flush mounted rails is Yakima. I recommend the following parts to complete your roof rack: Yakima HD Crossbars - 55" Long # Y01156 SkyLine Towers # Y53TR Landing Pad 28 # Y66VR HD...
  view full answer...
  
• What is the Difference Between Yakima HD Tracks and Regular Yakima Tracks?
  The difference between the Yakima HD Crossbars like the # Y74MR and the regular Yakima Tracks like the # Y01135 is that they are compatible with different feet and adapters. With the HD tracks, they will fit the Yakima Skyline towers, OverHaul HD system, or OutPost HD systems. In order to use these components, you need to use the Landing Pad 26 for Yakima SkyLine Towers - Qty 2 # Y75ZR or the Yakima HD Track Adapter Kit for Yakima OverHaul HD and OutPost HD Truck Racks - Qty 4 # Y75RR....
  view full answer...
• Recommended Roof Rack for Mounting a Thule Hullavator Pro on a 2021 Toyota RAV4
  The Thule Hullavator Pro, part # TH898, does in fact need crossbars that extend 4" - 8" beyond the feet. To use the flush rails on your 2021 Toyota RAV4, you will need a roof rack that has feet that are compatible with the rails. With those two stipulations in mind, the Thule WingBar Evos don't look like they will provide enough clearance with their 47" of crossbar length. Instead, I recommend the Yakima HD Crossbars, part # Y01156. They are 55" long, so they will have the extension you...
  view full answer...
• Can 60 Thule AeroBlade Bars be Used on a 2015 Jeep Grand Cherokee with the E Group Package
  To determine if you can use the 60" WingBar Evo Crossbars, part # TH711500 or part # TH711520, will fit on your 2015 Jeep Grand Cherokee you first need to measure the center to center distance between the mounting holes where the Podium feet will sit. I have attached a picture showing where you want to measure. If this measurement falls between 46-1/2" - 59-3/4" then the 60" bars will fit. For your E Group package you also need the Podium Foot Pack # TH460R and the Fit Kit # THKIT3142 to...
  view full answer...
  
• Can Thule Hullavator Install on Yakima Crossbars
  The Thule Hullavator Pro # TH898 can fit round bars by grabbing around the crossbar and can fit aero shaped bars if the bars have a channel on top of them. Which the Yakima aero shaped bars don't have top channels so to go the Yakima route will require round bars which includes the part numbers # Y00408, # Y53TR, # Y03536, and # Y00241 and you'd be set.
  view full answer...
• Recommended Yakima Roof Rack Upgrade for Subaru Factory Roof Rack
  The factory roof rack on the 2016 Subaru Outback Wagon has minimal options to fit the factory roof rack which is different than the factory side rails or flush mounted rails. You can use the Landing Pad 15 for Yakima Control Towers - Qty 4 # Y00241 which will allow you to simply remove your factory crossbars and mount these pads in their place. Then you can use the SkyLine Towers for Yakima Crossbars # Y53TR and round bar adapter # Y03536 if you want to use round bars like the 48 inch...
  view full answer...
  
• Roof Rack Option For A 2016 Lexus GX460 With Factory Flush Rails
  Good morning, Doug. I do have a potential solution for you, but I am sorry to say that Thule does not make a fit kit for the 2016 Lexus GX460. So, there is unfortunately no way to mount your Thule Evo bars on this vehicle. Our best option would be to get a whole new roof rack. Yakima does make a fit kit for the 2016 GX460 flush rails, so one of their JetStream racks would be a great option that is comparable to Thule. The complete Yakima roof rack consists of the following parts: - Yakima...
  view full answer...
• Installation of Yakima Roof Rack on 2019 Jeep Grand Cherokee With Flush Mount Rails
  Assuming your 2019 Jeep Grand Cherokee has the black and chrome flush-mounted rails that run front to back, you are correct that the roof racks you mentioned do install into the same place the factory bolts are. I have added links to an installation video of the Yakima JetStream roof rack on a Jeep Grand Cherokee with flush mount rails so you can see exactly how the rack installs. The Yakima JetStream (which is shown in the accompanying photo installed on a Jeep Grand Cherokee) consists...
  view full answer...
  
• How to Carry the Yakima MajorShady 270 Awning on a 2024 Subaru Outback Wagon
  The Yakima MajorShady 270 Awning # Y82AV installs via the T-Slots in a roof rack so we'll need to get you an aftermarket roof rack since your 2024 Subaru Outback Wagon OEM crossbars don't have that T-Slot system. For something that's cost-effective and gets the job done I recommend the Malone AirFlow2, but if you're wanting something with higher quality and will be a better setup for longevity then I recommend the Yakima JetStream system. Here are the parts you'll need for each: Malone...
  view full answer...
• Recommended Roof Rack For Installing A Yakima ShowDown Kayak Carrier On A 2021 Toyota Highlander
  For your 2021 Toyota Highlander with flush mounted rails I recommend the Roof Rack by Yakima which includes: Yakima HD Crossbars - Aluminum - Black - 55" Long - Qty 2 # Y01156 SkyLine Towers for Yakima Crossbars # Y53TR Landing Pad 28 for Yakima SkyLine And Control Towers - Qty 4 # Y66VR HD Bar SL Adapter # Y03541 The Yakima ShowDown Kayak or SUP Carrier and Lift Assist w/ Tie-Downs # Y04081 will clamp onto the crossbars of this roof rack system for an easy peasy installation. You will...
  view full answer...
• Roof Rack for 2018 Tacoma With Leer XR100 Cap And Thule Rails
  Hey Bill! You aren't finding the fit kit because Thule discontinued the one for rails and doesn't have a replacement right now. My recommendation is to install a Yakima roof rack instead. This will still fit the Thule tracks, and their JetStream bars are comparable to the WingBar. You will need the following: -SkyLine Towers for Yakima Crossbars # Y53TR -Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 -Yakima JetStream Crossbars - Aluminum - Black - 50" Long # Y00425 OR -Yakima...
  view full answer...
• Recommended Roof Rack for Hullavator and Kayak Carrier on 2019 Honda Pilot
  Thank you for all of the information! While you are able to use the Hullavator # TH898 with your setup as far as weight goes, this kayak carrier does require the crossbars to stick out 4" - 8" out past the roof rack feet. Since the Thule SquareBars have a limited amount of space under them for the feet you can only use the 53" Bars # TH712400 but this wouldn't give you the required spacing for the Hullavator. I recommend using the Yakima 60" JetStream Crossbar # Y00426 instead with the...
  view full answer...
• Yakima Roof Rack for 2023 Subaru Outback With Thule Hullavators
  Hi Tina; I also prefer Yakima so I'm glad we're on the same page. For your 2023 Outback and Hullavators I recommend the JetStream roof rack. You will need the following: -Yakima JetStream Crossbars # Y00426 -SkyLine Towers for Yakima Crossbars # Y53TR -Landing Pad 27 for Yakima SkyLine And Control Towers # Y46VR The JetStream crossbars are extremely quiet so you won't have a bunch of road noise added to your day to day driving. If you want to keep your rack secure you can also add the...
  view full answer...
• Roof Rack System for 2026 Chrysler Pacifica
  Hey Scott! No, the Rhino-Rack Aero Bar Roof Rack for Camper Shells - Track Mount - Black - 54" Bars # Y02-480B will not work on your 2026 Chrysler Pacifica. There is no custom fit kit for your van so instead, you will need to use components to build a roof kit for your van. For the front to back rails, you can use Yakima 54" Tracks for Roof Racks # Y01127 and that will be used as your base for the system. This system will require drilling through your vehicle's roof for the installation....
  view full answer...
• Can You Use the Yakima HD Bar Adapter part # Y03541 to Add Yakima HD Bars to the RetraxPRO XR?
  Hi Daniel, The short answer is yes! You can use the Yakima HD Bar Adapters for Yakima Streamline Towers part # Y03541 to use your Yakima crossbars in a RetraxPRO XR tonneau cover! You will need a few parts to accomplish this though: HD Bar SL Adapter for Yakima Towers part # Y03541 SkyLine Towers for Yakima Crossbars part # Y53TR Landing Pad 1 for Yakima Control Towers part # Y00221 Yakima HD Crossbars- 60" Long # Y01157, 68" Long # Y01158, or 78" Long # Y01159 (you'll need to measure...
  view full answer...
• What Roof Basket will Attach Directly to My Raised Rails on My 2022 Toyota 4Runner?
  I have a great option for you if you do not like the height of the Yakima LockNLoad # Y05045 with the Timberline Towers # Y33TR on your raised factory side rails on your 2022 Toyota 4Runner. Unfortunately, I confirmed with Yakima that you will need to have the Timberline Towers in order to attach the LockNLoad to your rails. They cannot be mounted without those towers directly to your rails. In order to complete this setup, you also need 2 sets of the LockNLoad SL Adapter for Yakima SkyLine...
  view full answer...
• 2021 Jeep Grand Cherokee L Yakima Roof Rack for Flush Rails
  I'd be more than happy to help out! The parts you need to get the Yakima JetStream roof rack installed on your 2021 Jeep Grand Cherokee L flush rails include the following: 50" JetStream Crossbars - # Y00425 SkyLine Towers - # Y53TR Landing Pad 19 - # Y00245 Lock Core Kit - # Y07204 (optional) This gives you the exact parts that were used in the linked video. If you let me know what you are planning on using this roof rack for I'd be more than happy to make a recommendation for you!
  view full answer...
• Parts Needed For A Yakima Roof Rack On A 2021 Ram ProMaster City With Factory Mounting Points
  Hi Phillip, To connect to the factory mounting points on the roof of your 2021 Ram ProMaster City you'll need Landing Pad 22 # Y00248 along with SkyLine Towers for Yakima Crossbars # Y53TR. From there you can go with crossbars like the Jetstream # Y00425 (50") or # Y00426 (60"). I've attached a picture below from Yakima's website showing this fit.
  view full answer...
• Roof Rack For Thule Tracks On 2025 Nissan Frontier LEER Cap
  Hey Stephen! For the Thule tracks on your LEER cap you can use the Evo Fixpoint Feet # TH49SC along with the Fit Kit # TH42KE. The closest Thule crossbars to the length you're looking for are the 69" ProBar Evo crossbars # TH713600. Before going that route, how far apart are the tracks on your cap? Thule's mounting channel underneath the crossbars doesn't run the full length of the bar, so the track spacing will determine whether they will work. As an alternative, you could use the 70"...
  view full answer...
• Roof Rack With Black Crossbars for Pace Edwards BedLocker Rails on 2019 Ford F-350
  Hi Michael; you can use the same fit kit # THKIT3101 and mounting feet # TH460R. However, the longest WingBar Evo is 60" # TH711520 which probably won't be long enough for your truck bed. That is why Conner originally chose the # TH713700 which are 79" long. For bars that are black I recommend switching to a Yakima setup. You will need the following: -Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 -SkyLine Towers for Yakima Crossbars # Y53TR -Yakima CoreBar Crossbars -...
  view full answer...
• Roof Rack for 2019 Subaru Outback with Rails to Carry Hullavator and Hull-a-Port
  The 47 inch bar would definitely not work for two Hullavators; thanks for calling that to our attention and that information has been edited. You would need crossbars that are a minimum of 76 inches for a pair of Hullavators.
  view full answer...
• Recommended Roof Rack For A 2023 Toyota RAV4 With A Thule Hullavator
  Hi Cathy, To ensure that you can get the extra extension to mount the Thule Hullavator # TH898 you'll want to go with a Yakima roof rack system. Yakima crossbars run their mounting track the entire length of the crossbar so you can go with ones that are longer than your typical length without worrying if the mounting feet will be able to connect. You'll want the following components: Yakima JetStream Crossbars - Black - 60" Long # Y00426 or silver # Y00429 SkyLine Towers for Yakima Crossbars...
  view full answer...
• Can I Use the Same Yakima Landing Pad on my 2025 Subaru Outback That I Used on My 2019
  That's a great question, Maryann! No, you can't use your existing Yakima Landing Pad 15 # Y00241 on your 2025 Subaru Outback Wagon. Instead, you would need to get the Yakima Landing Pad 27 # Y46VR. You will still be able to use your SkyLine Towers # Y53TR and just swap them out for the Landing Pad 27. Congrats on the new Subaru! What are you usually carrying on the roof?
  view full answer...
• Can I Put The Yakima Locknload Size K on the Roof of my 2025 Jeep Grand Cherokee L
  Thanks for your question, Bobby! The answer is, yes, you can mount the Locknload (K size) with the right parts. I wasn't sure if you had or had some of these parts so I'll go ahead and keep it simple and list all the parts below for you. Landing Pad 19 for Yakima SkyLine and Control Towers set of 4 - part # Y00245 SkyLine Towers for flush rails set of 4 - part # Y53TR LockNLoad SL adapter for Yakima SkyLine towers set of 4 - part # Y05042-2 Yakima LockNLoad platform size K part # Y05044 I...
  view full answer...
• What Roof Basket will Attach Directly to My Raised Rails on My 2022 Toyota 4Runner?
  I have a great option for you if you do not like the height of the Yakima LockNLoad # Y05045 with the Timberline Towers # Y33TR on your raised factory side rails on your 2022 Toyota 4Runner. Unfortunately, I confirmed with Yakima that you will need to have the Timberline Towers in order to attach the LockNLoad to your rails. They cannot be mounted without those towers directly to your rails. In order to complete this setup, you also need 2 sets of the LockNLoad SL Adapter for Yakima SkyLine...
  view full answer...
• Can I Put The Yakima Locknload Size K on the Roof of my 2025 Jeep Grand Cherokee L
  Thanks for your question, Bobby! The answer is, yes, you can mount the Locknload (K size) with the right parts. I wasn't sure if you had or had some of these parts so I'll go ahead and keep it simple and list all the parts below for you. Landing Pad 19 for Yakima SkyLine and Control Towers set of 4 - part # Y00245 SkyLine Towers for flush rails set of 4 - part # Y53TR LockNLoad SL adapter for Yakima SkyLine towers set of 4 - part # Y05042-2 Yakima LockNLoad platform size K part # Y05044 I...
  view full answer...
• Low Profile Roof Platform Recommendation for 2020 Toyota 4Runner with Factory Side Rails
  For your 2020 Toyota 4Runner with the factory side rails, I recommend the Yakima LockNLoad Platform Roof Tray 60" Long x 54" Wide, part # Y05045. It's pretty low profile at only 4 inches tall, and it will not interfere with your sunroof, since it will sit right behind it. I've attached a couple of photos so you can see for yourself. To attach the platform, you'll need the LockNLoad SL Adapters # Y05042-2 (qty 4), and TimberLine Towers # Y33TR (qty 4). This will add approximately another...
  view full answer...
  
• Parts Needed To Install Yakima Platform On 5' Leer Topper
  Hey Michael, sure can! For a 5' Leer topper, I am thinking the 55" long x 49" wide LockNLoad platform will be the best bet and will fit comfortably on the topper. Here is a list of all the parts you will need for that: - Yakima 54" Tracks for Roof Racks # Y26RR - Landing Pad 1 for Yakima SkyLine and Control Towers - Qty 2 # Y00221 (you will need two of these) - SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4 # Y53TR - LockNLoad SL...
  view full answer...
• 2018 Toyota 4Runner OEM Crossbars Fitment with Yakima LockNLoad Platform Rack
  The Yakima LockNLoad Platform Rack for Crossbars # Y05047-39 will fit your 2018 Toyota 4Runner, but you'll need to use aftermarket crossbars because the OEM crossbars sit too low to the roof and this mounting hardware won't fit. To install an aftermarket roof rack I recommend the Malone AirFlow2 # MPG216 because it is a cost-effective solution that will get the job done. If you'd like a solution that looks a little more custom fit the you can use the 60" Long x 54" Wide LockNLoad Platform...
  view full answer...
• What is Needed to Add Yakima LockNLoad to 2021 Subaru Outback With Side Rails
  Hey Jeremy, I believe you're asking what you need to mount the Yakima LockNLoad Platform Roof Tray # Y05044 directly to the side rails on your 2021 Subaru Outback, and if so, I verified directly with Yakima the exact parts you'll need: - SkyLine Towers # Y53TR - Landing Pad 27 # Y46VR - LockNLoad SL Adapters # Y05042-2 And that's it! These parts are all need to mount the LockNLoad directly to your Outback.
  view full answer...
• Parts Needed to Add Yakima LockNLoad Platform on a 2021 Nissan NV 3500
  Hey Garrett, thanks for reaching out! I'm pretty sure at the time that Bob wrote that answer Yakima had only come out with their crossbar clamps for the LockNLoad and they were geared up to get all of the direct fits in their system but we were still waiting on that. Nevertheless, there is a way to install the LockNLoad directly to your 2021 Nissan NV 3500 and you had almost all of the pieces laid out in your comment (might as well give you the title "Expert" as well!). The only parts...
  view full answer...
• Can 2023 Subaru Outback Wilderness Use Yakima LockNLoad Platform Without Crossbars
  Hi David, Yep, you can use the LockNLoad on your 2023 Subaru Outback Wilderness without having to use crossbars. I checked directly with Yakima for you to verify this, though you will need the larger 60" x 54" platform to fit the width of your Outback. Here is exactly what you'll need: - Yakima LockNLoad Platform Roof Tray - 60" Long x 54" Wide # Y05045 - TimberLine Towers # Y33TR - LockNLoad SL Adapter - Qty 4 # Y05042-2
  view full answer...
• What is the Recommended LockNLoack Platform for My 2022 Subaru Outback Wilderness?
  For your 2022 Subaru Outback Wilderness, Yakima recommends the Yakima LockNLoad Platform Roof Tray - Aluminum - 60" Long x 54" Wide # Y05045. Since your vehicle has raised factory rails, you will need to purchase the TimberLine Towers # Y33TR along with the LockNLoad SL Adapter for Yakima SkyLine and TimberLine Towers # Y05042-2 to attach directly to the rails.
  view full answer...
• Can I Size Down From A LockNLoad Platform B To A LockNLoad Platform K
  You should be able to use the Yakima LockNLoad Platform Roof Tray - Aluminum - 55" Long x 49" Wide, part # Y05044, on your vehicle. If your crossbars are at least 27" apart and less than 33" apart, you should not have any problems mounting the platform to your vehicle. Do keep in mind that you will need an adapter to mount this platform directly to your towers. The LockNLoad SL Adapter for Yakima SkyLine and TimberLine Towers - Qty 4, part # Y05042-2, will attach directly to your Yakima...
  view full answer...
  
• How Can I Attach A Yakima LockNLoad Platform To My 2022 Subaru Outback Wagon W/ Factory Roof Rack
  You will be able to carry a LockNLoad Platform on your 2022 Subaru Outback Wagon, but it will not fit on your factory cross bars. In order to carry this platform, you will need the following: SkyLine Towers for Yakima Crossbars, part # Y53TR, Landing Pad 27, part # Y46VR, Yakima LockNLoad Platform Rack for Crossbars, part # Y05044-39 LockNLoad SL Adapter, part # Y05042-2, and the Yakima Same Key System (SKS) Lock Cores (QTY 4), part # Y07204. This roof rack setup will allow you to...
  view full answer...
• What is Height of LockNLoad Platform Rack for LEER Camper Topper on a 2020 Nissan Frontier
  To install the LockNLoad on your 2020 Nissan Frontier 5' Bed LEER camper topper you need the following parts: - 55" Long x 49" Wide Yakima LockNLoad Platform Roof Tray # Y05044 - TrackTowers # Y52AV - LockNLoad SL Adapter # Y05042-2 The TrackTowers sit about 2" tall and the LockNLoad is around 4" tall so you'll be adding about 6" to the height of your LEER topper which is pretty standard for a track mount platform. You'll be pretty hard-pressed to find something only sitting 3-1/2"...
  view full answer...
• Recommended Platform Rack for a 2021 Subaru Ascent
  I did a little digging around and it looks like the roof on your 2021 Suabru Ascent is around 63 inches, making the Yakima LockNLoad Platform Roof Tray # Y05045 with the TimberLine Towers for Yakima Crossbars # Y33TR, and the LockNLoad SL Adapter for Yakima SkyLine and TimberLine Towers # Y05042-2 near perfect. This platform rack measures 60" long, 54" wide, and will be a perfect addition to your Subaru for all your camping and luggage needs. This rack also has top channels so you can...
  view full answer...
• Can Yakima LockNLoad be Installed on 2021 Toyota 4Runner OEM Roof Rack
  Great question! The OEM roof rack on your 2021 Toyota 4Runner looks nice but it sits too low to your roof for the Yakima LockNLoad # Y05045-39 mounting hardware to fit. Instead of purchasing a roof rack AND the LockNLoad what I recommend doing is picking up the parts to mount the LockNLoad directly to the raised rails on your 4Runner: 60" Long x 54" Wide LockNLoad # Y05045 SL Adapter # Y05042-2 TimberLine Towers # Y33TR We don't have any brackets designed to fit with the ARB awnings...
  view full answer...
• Rhino-Rack Pioneer Platform Rack for 2019 Ford Expedition with Factory Rails and No Crossbars
  I actually had the chance to work with a 2019 Ford Expedition. While in the shop, I tested the RhinoRack roof racks we had shown to be compatible with the factory installed rails and to my surprise, the SX Series Legs # RRSX100 were not a fit. When trying to install them, I could tell they were not tall enough to catch on the rather large and triangular shape of the Expedition rails. The only style of legs or towers that will work is the kind that wraps around the entire bar, like the...
  view full answer...
  
• Can Yakima LockNLoad Platform For 2017 Toyota Highlander XLE be Used with Roof Tent
  The Yakima LockNLoad Platform part # Y05045, # Y53TR, # Y05042-2, and # Y00242 would work great for your tent setup. This will give you a 165 lb dynamic weight capacity which is the standard capacity needed for tents which would use a static capacity instead and would be much higher. This is a creative solution to give you the additional spread you'd need for your tent too!
  view full answer...
• Can You Use a Larger Yakima LockNLoad Platform Roof Tray on a 2023 Ford Expedition Than the 60"x54"
  You are correct that the 2023 Ford Expedition Platform Roof Rack by Yakima will fit the raised side rails on your Expedition. The 2023 Ford Expedition Platform Roof Rack by Yakima consist of: - Yakima LockNLoad Platform Roof Tray # Y05045 - TimberLine Towers for Yakima Crossbars # Y33TR - LockNLoad SL Adapter for Yakima # Y05042-2 I have an alternate option, but you would not be able to use the Yakima LockNLoad Platform Roof Tray # Y05048 (84" Long x 54" Wide) on your 2023 Ford Expedition....
  view full answer...
• Recommended Platform Rack System without Crossbars for 2019 Toyota Highlander XLE
  For a low profile platform style rack similar to a Rhino Rack Backbone System, the only available option is the Yakima Roof Rack and Platform System that uses parts # Y05045, # Y53TR, # Y05042-2, # Y00242. This kit combines the Yakima Lock N Load Platform # Y05045 and Yakima Skyline towers # Y53TR to give you the platform without a crossbar for the low profile setup you're looking for. The additional parts are for the footpack and adapters to allow you to mount the towers to your 2019...
  view full answer...
• Larger Roof Platform Tray that Fits 2023 Honda Pilot
  We have a larger platform tray that fits the roof of your 2023 Honda Pilot with flush side rails with the Yakima LockNLoad part # Y05045, # Y53TR, # Y05042-2, # Y00245 which will give you a platform that is 60 inch by 54 inch. There isn't a Rhino Rack option at this time that fits.
  view full answer...
• Correct Yakima LockNLoad Platform Roof Tray For a 2016 Honda CR-V with Flush Side Rails
  In order to use the Yakima LockNLoad Platform Roof Tray on a 2016 Honda CR-V with flush side rails you will need to use the following; part # Y05044, part # Y53TR, part # Y05042-2, and part # Y00245. This will be a direct mount option which mounts to factory fixed points . The tray also mounts directly to the mounting feet so there is no need for additional crossbars and adapters.
  view full answer...
• Can Yakima LockNLoad Platform for 2011 Jeep Patriot Support Yakima SkyRise Tent
  The Yakima LockNLoad Platform Roof Tray part numbers # Y05045, # Y33TR, and # Y05042-2 that fits your 2011 Jeep Patriot can be used with roof top tents like the Yakima SkyRise Tent part # Y79XR that you mentioned without requiring any additional support.
  view full answer...
• Carrying A Yakima LockNLoad Platform On 2007 Chevy Suburban
  The Yakima LockNLoad Platform Roof Tray - Aluminum - 84" Long x 54" Wide, part # Y05048, needs a roof rack in order to attach to your 2007 Chevy Suburban. Your vehicle's roof either has raised rails or fixed points, so it has two separate roof rack fits. Each option has a maximum weight limit of 165lbs. Please keep this in mind because the weight of the rack and the accessories are part of the maximum weight limit and the LockNLoad Platform weighs 70lbs and the roof rack will weigh approximately...
  view full answer...
• Will the Rhino-Rack Pioneer Platform # JB0892 Fit on My 2014 Jeep Grand Cherokee with Flush Rails?
  I have a solution for you. As far as mounting a Pioneer platform 72" x 56" and Backbone like the # JB0892 on your black and chrome raised rails of your 2014 Jeep Grand Cherokee, I confirmed with Rhino-Rack that they do not have an engineered fit of that size of platform for your roof. Also, we do not carry a Backbone that is guaranteed to fit your roof. Regrettably, your rails will not work with the RCL Legs for Rhino-Rack Crossbars and Pioneer Platforms # RRRCL6 either. With that being...
  view full answer...
• Roof Platform Tray that Fits 2015 Chevy Tahoe
  I have a way to install a roof platform tray similar to a Rhino Rack Pioneer Platform but Rhino Rack does not have a fit for your 2015 Chevy Tahoe. Instead you'd need to go with a Yakima LockNLoad with the part # Y05045, # Y53TR, # Y05042-2, # Y00243 which gives you a 60 inch by 54 inch platform confirmed as a fit.
  view full answer...
• Will the Yakima SteelHead Roof Mounted Bike Carrier Fit Aero Crossbars on a 2017 Toyota Highlander
  In order to use the Yakima SteelHead Roof Mounted Bike Carrier on your 2017 Toyota Highlander you would need to install a round bar system like the Yakima Roof Rack System part # Y00408, part # Y53TR, part # Y03536, and part # Y00242 if you have flush side rails or the Yakima Roof Rack System part # Y00409, part # Y28TR, part # Y03536, and part # Y06130 if you have a bare roof. If you want to keep the roof rack you have now then I recommend selling the SteelHead and buying the Yakima...
  view full answer...
• Can Yakima LockNLoad Platform For 2017 Toyota Highlander XLE be Used with Roof Tent
  The Yakima LockNLoad Platform part # Y05045, # Y53TR, # Y05042-2, and # Y00242 would work great for your tent setup. This will give you a 165 lb dynamic weight capacity which is the standard capacity needed for tents which would use a static capacity instead and would be much higher. This is a creative solution to give you the additional spread you'd need for your tent too!
  view full answer...
• Installing Roof Rack on 2019 Toyota Highlander w/ Flush Rails & Can it Use Longer Crossbars Bars
  Good questions so let's start with the installation of the roof rack feet on your 2019 Toyota Highlander and you do need to install the feet at the locations indicated in the directions, which is what we show in the linked installation video. A short crossbar spread really is a positive, as it allows you the use of more accessories, which will fit that spread compared to what looks to be a very long spread if you install the fit in different mounting locations. You can use longer crossbars...
  view full answer...
• Roof Rack Recommendation to Carry Thule Pulse Box on 2018 Toyota Highlander
  In order to carry the Thule Pulse Large Rooftop Cargo Box # TH615 on your 2018 Toyota Highlander you will need crossbars that are perpendicular to your vehicle body so that the box can be parallel with the vehicle body. I really like the Yakima JetStream roof rack system because the crossbars are higher quality with that aero-style design and the legs have adjustments so you get the best fit possible. I'm guessing you have a naked roof but in the event that you do have the flush mount rails...
  view full answer...
• Roof Rack For 2018 Toyota Highlander w/ Flush Mount Rails For Rooftop Tent
  We have a roof rack and rooftop tent for your 2018 Toyota Highlander with flush mount rails, though the crossbar spread on your Highlander is set at 27-1/2 inches. The reason for that is roof racks install at fixed mounting points on the rails, which means a tent requiring a larger spread won't work. That said, there is still a really nice option for a rack and tent for your '18 Highlander, and let's go ahead and start with the rack you'll need, which is from Yakima: - Yakima JetStream...
  view full answer...
• Recommended Platform Rack System without Crossbars for 2019 Toyota Highlander XLE
  For a low profile platform style rack similar to a Rhino Rack Backbone System, the only available option is the Yakima Roof Rack and Platform System that uses parts # Y05045, # Y53TR, # Y05042-2, # Y00242. This kit combines the Yakima Lock N Load Platform # Y05045 and Yakima Skyline towers # Y53TR to give you the platform without a crossbar for the low profile setup you're looking for. The additional parts are for the footpack and adapters to allow you to mount the towers to your 2019...
  view full answer...
• Recommended Roof Rack to Use the Yakima SideWinder on a 2018 Toyota Highlander LTD
  I recommend installing a Yakima JetStream roof rack on your 2018 Toyota Highlander because they provide a clean looking installation that allows you to utilize the full 165 lb weight capacity and can be keyed alike with your SideWinder # Y02071. If you have a naked roof (no rails running from front to back) then you need the 60" JetStream Bars # Y00426 the BaseLine Towers # Y28TR, and the BaseClip # Y06130. For flush mount rails you would instead need the 50" JetStream Bars # Y00425,...
  view full answer...
• Can Two Sets of Yakima Y04073 JayLow Kayak Carriers Fit on 2018 Toyota Highlander Factory Roof Rack
  Each of the # Y04073 JayLow kayak carriers will take up approximately 10.3 inches of space on the crossbar. Factory crossbars won't extend past the roof side rails, so even though you should be able to fit two sets of the carriers on the roof, you might not be able to place them far enough apart on the crossbars to accommodate the two kayaks you'll want to place in the center. What I'd recommend you do is measure the length of your factory crossbars, and compare that to the combined width...
  view full answer...
• Yakima Roof Rack Landing Pad 16 Wont Line Up On 2019 Toyota Highlander
  There are two roof configurations on a 2019 Toyota Highlander, bare roof and flush side rails. The Landing Pad 16 part # Y00242 is designed for models with flush side rails. If you have a bare roof you need to use the BaseClip Fit Kit part # Y06130. I think you might be looking at the pre-drilled holes in the roof used to attach the flush side rails from the factory and if so these can't be used and you would have to use the rack for bare roof models. I have attached a video below of the...
  view full answer...
• Recommended Roof Rack To Carry Kayak And SUP On A 2016 Toyota Highlander LE Plus
  I do have a roof rack to fit your 2016 Toyota Highlander LE Plus. Your options will be based upon what type of roof you have on your vehicle. If you have flush rails on your vehicle, your roof rack will consist of the following items. Yakima CoreBar Crossbars - Steel - Black - 50" Long - Qty 2, part # Y00421 SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems - Qty 4, part # Y53TR Landing Pad 16 for Yakima SkyLine and Control Towers - Qty 4, part...
  view full answer...
• 2014 Toyota Highlander Yakima Rack Fit W/ Round Crossbars
  It really depends on the accessory in question. Most rack manufacturers are going with elliptical shaped bars. These bars help with wind noise and fuel efficiency. Oftentimes, these racks will utilize crossbars with t-channels. Now if your accessory does not have the ability to attach to a t-channel it will have to clamp to the crossbars. If your accessory is designed to only clamp round or square crossbars you will need an adapter, but not all accessories are compatible with an adapter....
  view full answer...
• Recommended Roof Rack For A 2019 Toyota Highlander To Carry A Thule Hullavator 898
  In order to use the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs - Side Loading, part # TH898, on the roof rack of your 2019 Toyota Highlander, the crossbars need to extend between 4" and 8" past the the towers/feet. My recommendation would be to go with a 60" crossbar for your roof rack. I have two roof rack recommendations for you. The first rack is for a Highlander with flush rails. It will consist of the following items: Yakima CoreBar Crossbars - Steel - Black...
  view full answer...
  
• What Parts are Needed to Install a Yakima RoundBar Crossbars for a 2018 Highlander?
  If you are trying to use the same round crossbars for the flush rails on your 2018 Toyota Highlander, you will need three parts: 1. SkyLine Towers for Yakima Crossbars # Y53TR 2. Landing Pad 16 for Yakima SkyLine and Control Towers # Y00242 3. RoundBar SL Adapter for Yakima BaseLine, SkyLine, TimberLine, and RidgeLine Towers # Y03536 These are all you need to adapt your existing setup on your 2008 Toyota Highlander.
  view full answer...
  
• What Do I Need To Install The Yakima RocketBox 14 On My 2015 Toyota Highlander
  First let's get you a roof rack system! I also like the Yakima Jetstream Bars # Y00425. If you have flush rails on your 2015 Toyota Highlander then you'll need the SkyLine Towers # Y53TR and the Landing Pad 16 # Y00242. If you have a naked roof, still grab the Jetstream bars along with the BaseLine Towers # Y28TR and the BaseClip Fit Kit # Y06130. You won't have any issues with opening the rear hatch. If you take a look at the video attached, the RocketBox has plenty of room on a 2012...
  view full answer...
• How To Carry a Cargo Box and Two Kayaks On a 2015 Toyota Highlander with Flush Rails
  In order to carry a cargo box and two j-style kayak carriers on a 2015 Toyota Highlander with flush rails you'll need to use at least a 70" crossbar. The problem with this is that most crossbars only have a certain amount of channel underneath to attach to the mounting feet so you can't just use order a larger bar. The Yakima Corebar however does not have this channel underneath so you can use part # Y00423 with part # Y53TR and part # Y00242 to fit all your accessories.
  view full answer...
• Will Yakima CoreBar Roof Rack for 2015 Toyota Highlander Allow fit Yakima Showdown Kayak Carrier
  I checked with Yakima just now and they have their Showdown Assisted Kayak carrier part # Y04081 as a fit with the CoreBar roof rack you also mentioned part numbers # Y00421, # Y53TR, and # Y00242. The bars are long enough for the carrier to fit and work well but wouldn't be obnoxiously long. You wouldn't have to worry about hitting your head or anything.
  view full answer...

Do you have a question about this Roof Rack?