Will Yakima RoadShower Work With Yakima LockNLoad

Question

Question:

Can I install a road shower on a Yakima lock and load platform and does it come with the parts to do it

asked by: RICHARD B

0

Expert Reply:

Yes, the Yakima RoadShower Portable Solar Shower part # Y29VR will work with the Yakima LockNLoad Platform Roof Trays like part # Y05045. I confirmed this with Yakima as well. There are no extra parts needed.

expert reply by: Conner L

0

Answer 1

Crossbar spread is measured from one point on the front crossbar to that same point on the rear crossbar. Since your roof rack measures 39" center to center on your crossbars this means that the Inno Wedge 660 Rooftop Cargo Box #INBRM660BK will…

view full answer...

Answer 2

Using stainless steel instead of regular steel for the stud on clearance light #MCL95RB would be fine. But what you can do to help the ground is attach a wire with ring terminal between the stud and where it makes contact with the trailer frame and…

view full answer...

Answer 3

A hitch ball does not make a good ground connection for trailer lighting functions. The fact that the lights work for a bit after you hit a bump with the hitched trailer tells us that somewhere in your trailer and vehicle wiring there is an…

view full answer...

Answer 4

Each lamp needs to be grounded either through its mounting studs being in direct contact with the trailer frame or by having a jumper wire ran from the lamp to the trailer frame. Ground the trailer connector at the front of the trailer, which will…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Will Yakima RoadShower Work With Yakima LockNLoad

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching