Curt Class I and II Pin and Clip - 1/2" Diameter

Ask the Experts about this Curt Hitch Pins and Clips

• Recommended Hitch Pin for 1-1/4" Class II Receiver
  It sounds like you're looking for a hitch pin for a 1/2" diameter as opposed to a 5/8" diameter; typically a 1/2" diameter hitch pin is designed to be used on a 1-1/4" hitch receiver. If you just need a hitch pin you can use the Curt # F-4. If you're looking for a locking hitch pin to keep your VersaHaul Carrier attached to your vehicle, you can use the etrailer # e98879. Both of these hitch pins are designed for 1-1/4" Class I or II hitch receivers. If you can tell me what vehicle you're...
  view full answer...
• Trailer Hitch and Wiring Harness for 2003 Honda Civic Sedan
  We do have a trailer hitch receiver that fits your 2003 Honda Civic, but it isn't the model you mentioned. Instead, your '03 Civic will need the Curt Trailer Hitch Receiver # C11204. Since you mentioned towing you will also need a wiring harness, ball mount/drawbar, pin & clip, and hitch ball. The correct parts for your Civic are: - Curt T-Connector Vehicle Wiring Harness # C56341 - Curt Drawbar # C45521 - Curt Class I and II Pin and Clip # F-4 - 1-7/8" Hitch Ball # A-80 or 2"...
  view full answer...
• Recommended Trailer Hitch and Towing Accessories for 2003 Mercedes C240 Wagon
  We do indeed have a Class I hitch available for your 2003 Mercedes C240 Wagon, part # C11824. If you'll be using the hitch for light duty towing purposes, the hitch has a 2500 lb towing/ 250 lb tongue weight capacity. You'll want to check with Mercedes/Benz or your owner's manual to determine the actual towing capacity of your Wagon, and not exceed whichever capacity is lowest. In order to tow with the hitch, you'll need the following items, which aren't sold in kit form but are available...
  view full answer...
• Trailer Hitch Receiver Fit for 2007 Volkswagen Jetta Wolfsburg
  We do have a trailer hitch receiver that fits your 2007 Volkswagen Jetta Wolfsburg, so long as it is the 4-door sedan and it does not have the diesel engine. If your '07 Jetta Wolfsburg meets those specs the correct trailer hitch fit is the Curt Trailer Hitch Receiver # C11474. I confirmed this fit for you with the manufacturer, and if you plan on doing some towing with your Jetta, there are a few other parts you'll need: - T-One Vehicle Wiring Harness # 118667 - Curt Drawbar # C45520 -...
  view full answer...
• Why Does my 2 Inch Hitch have a 1/2 in Pin Hole and a 5/8 in Pin hole
  The Curt Pin and Clip # F-4 that you referenced is designed to work on 1-1/4 inch hitches. The reason your hitch has a 1/2 inch hole and a 5/8 inch hole is because it is setup for an anti-rattle device like the Draw Tite J-Pin # 63201. I attached a picture of this device being used on a hitch like yours for you to check out. I also attached a review video for this product for you to check out also. This 1/2 inch hole is not designed to be use as a hitch pin hole, you will want to use...
  view full answer...
• Best 1/2 Inch Hitch Pin that is Long Enough to Fit a 2 Inch Hitch Receiver
  Is there a threaded nut inside the shank of the bike rack? My guess is that is the case. I would need to know the bike rack manufacturer and the model though the model is not as important as the manufacturer. If you can tell me that information I can determine if we have the proper threaded hitch bolt for that rack. If it does not have a threaded hitch pin hole and the issue is length you can use the Curt Clevin Pin with Handle # C45805. This pin has a 6-7/8 inch usable span so it is...
  view full answer...
• Trailer Hitch, Ball Mount, Ball, and Wiring for a 2013 Ford Mustang Towing a Small Trailer
  For a compatible trailer hitch for your 2013 Ford Mustang I recommend Draw-Tite trailer hitch # 24863. The recommended ball mount is # 3594. For a 1-7/8 inch ball use # 19256. If you ever need a 2 inch ball use # 19258. For trailer wiring you can use # 118487. Motorcycle trailers typically are designed with separate brake and turn signal lights. But since your trailer uses a 4-Way connector you will not need to add any type of converter for it to work with the trailer wiring mentioned...
  view full answer...
• Trailer Hitch Fit for 2013 VW Jetta Hybrid Sedan
  There is just one trailer hitch receiver I can confirm directly from the manufacturer is a fit for your 2013 Volkswagen Jetta sedan, though not the Draw-Tite you referenced. For a 2013 VW Jetta Hybrid sedan, the trailer hitch receiver I can confirm fits is the Curt Trailer Hitch Receiver # C11474. If you plan on doing any towing you will also need the T-One Vehicle Wiring Harness # 118572, Drawbar for 1-1/4" Hitches # C45520, Pin and Clip # F-4, and either 1-7/8" hitch ball # C40001...
  view full answer...
• Can Hole be Drilled in Trailer Hitch to Align With Ball Mount
  I do not recommend drilling a hole in a trailer hitch like the Draw-Tite # 76154 that fits a 2019 Nissan Titan as not only will this void the warranty but hitches have not been tested to be used after modification. A Class III, 2" hitch like the Draw-Tite is designed to be used with a 5/8" diameter pin and clip such as # PC3, while a 1-1/4" hitch will use a 1/2" diameter pin and clip like # F-4.
  view full answer...
• Pin and Clip That is 1/2 Diameter and 4 Long
  I'm not 100 percent sure what you mean by "latch pin or something" but I am assuming you mean a pin and clip, and we do have one that is 1/2" diameter and 4" long, the Curt Class I and II Pin and Clip # F-4. This pin and clip is a total of 4" long overall with a 2-1/2" long straight pin. The 1/2" diameter is standard for a hitch pin and clip for a 1-1/4" receiver so the straight part of these is not going to be as long. If you were looking for a hitch lock the longest with a 1/2"...
  view full answer...
• Does My 2020 RAM 3500 Have Non-Standard Hitch Pin?
  We have never seen an 1/2" diameter hitch pin on a 2-1/2" receiver. They all have 5/8" standard. We only see the 1/2" pins on the small 1-1/4" receivers. I would measure your hitch pin carefully. Is it possible that everything is 5/8" but just has a loose fit? Hitch parts do not have tight tolerances and tend to wiggle and rattle a little. Most likely your setup is just fine.If the rattling becomes annoying you can always add a Trailer Hitch Anti-Rattle Kit for 1-1/4" Trailer Hitches,...
  view full answer...
• Hitch Pin Recommendation for a Curt Ball Mount C45503
  I checked your order notes and it looks like you ordered the Curt Ball Mount part # C45503 and the hitch ball part # A-82. For a standard hitch pin and clip you would want the part # F-4 or for one that would lock and give you a bit more security you would want the locking hitch pin part # e98879 which is designed for 1-1/4 inch hitches. I attached a review video for this lock for you to check out as well.
  view full answer...
• Trailer Wiring Harness That Fits 2021 Kia Seltos
  The trailer wiring harness that fits your 2021 Kia Seltos is the Curt T-Connector Vehicle Wiring Harness # C89KR. Along with the wiring harness, the trailer hitch that fits your '21 Seltos is the Curt Trailer Hitch Receiver # C65FR. It sounds like you are planning to do some towing so you will also need the Curt Class II Drawbar # C45521 with Trailer Hitch Receiver Lock # C23517 or Pin and Clip # F-4 to secure it to your hitch. For a hitch ball you will need either 1-7/8" Hitch Ball...
  view full answer...
• Trailer Hitch Fit For 2015 Ford Fiesta ST Hatchback
  The 2015 Ford Fiesta ST is the hatchback model, and there are a pair of trailer hitches that will fit your car, the Draw-Tite Trailer Hitch Receiver # 24961 and Curt Trailer Hitch Receiver # C11067. The accompanying photo is of a hitch on a Fiesta; I have also added a link to an install video so you can see exactly what you'll need to do. The only trimming you'll need to do is a 2" section of the heat shield which means there is no fascia trimming needed at all. Though both hitches...
  view full answer...
• Parts Needed to Tow a Boat Trailer with a 2017 Honda HR-V
  I'll be happy to help you get your 2017 Honda HR-V setup for towing a boat trailer! Whenever a 2" hitch receiver is available for a vehicle I usually recommend going that route just because it allows you to use a wider variety of accessories. So for a hitch I recommend using the EcoHitch # 306-X7322 which has the 2" receiver and a hidden crosstube, however since I know that pricing is always a factor if you wanted something a little more cost-effective I recommend the Curt Trailer Hitch...
  view full answer...
• Parts Needed To Tow a Trailer or Haul a Cargo Carrier with a 2015 Volkswagen Golf TDI
  The easiest to install trailer hitch we have for your 2015 Volkswagen Golf TDI is the Curt Trailer Hitch Receiver part # C11412. The reason that this trailer hitch is the easiest to install is because you don't have to take off any part of the rear bumper fascia like you would have to for the other options available for your Golf. I have attached an install photo and video for you as well. The Curt Trailer Hitch Receiver has a class I rating with a 1-1/4" receiver tube opening. Therefore,...
  view full answer...
• Comparing the Curt Trailer Hitches C12164 and C12091 for a 2017 Ford Fusion
  In regards to a 2017 Ford Fusion, the Curt Trailer Hitch Receiver part # C12164 is a fit for sport models and the Curt Trailer Hitch Receiver part # C12091 is a fit for non-sport models. They are both great bolt-on options that will work well for you. The frame brackets on the hitch are different since the frame configuration on the vehicle is different for the two models. If you will be towing then you'll also need the T-One Vehicle Wiring Harness part # 118574 which is a plug and...
  view full answer...
• Hitch Pins for Use with Curt Trailer Hitch Receiver Adapter # C45770
  Hitch pins are not included with the Curt Trailer Hitch Receiver Adapter # C45770. The reason they aren't is that not everyone needs a hitch pin so instead of forcing people to pay extra for a part they may not need it's offered separately. For the 1-1/4 inch portion of the adapter the pin and clip you'd need is the part # F-4 and then for the 2 inch portion you'd want the part # PC3.
  view full answer...
• Trailer Hitch Receiver Fit on 2020 Hyundai Venue
  You'e in luck as there is a trailer hitch receiver that is a fit for a 2020 Hyundai Venue, which is the following: - Curt Trailer Hitch Receiver # C57CR This is a Class I hitch with a 1-1/4 inch receiver, and is a complete bolt-on installation with no drilling needed. It also has a really nice concealed look, as you can see from the accompanying photo, so your '20 Venue will maintain it's aesthetic. I have added a link to the installation instructions for you to check out as well. If...
  view full answer...
• Recommended Trailer Hitch for 2019 Volkswagen Jetta
  The available 1-1/4-inch Class I hitch options for your 2019 Jetta include the Curt round tube hitch # C11540 and the Draw-Tite model # 24978. The Curt offers easier installation but its cross tube will be visible under the bumper cover. The Draw-Tite hitch installation requires removal of the entire bumper fascia and the bumper itself but gives you a much more discrete appearance once installed. The linked photo shows the Draw-Tite hitch. Both hitches include all of the required mounting...
  view full answer...
• 2007 Subaru Impreza Hitch Compatibility with Dirt Bike Motorcyle
  The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11497 or the Draw-Tite Sportframe Trailer Hitch Receiver # 24710 are the fit for a 2007 Subaru Impreza. These are both rated for 200 lbs tongue weight but won't allow for the 2 inch opening for your motorcycle carrier. Using an adapter would reduce your capacity by 50%, and would also need to include the carrier weight. With your dirt bike weighing around 190 pounds, we do not have a cargo carrier option that would allow...
  view full answer...
• Recommended Trailer Hitch and Wiring For 2010 Toyota Prius
  You can use Curt Class I hitch part # C11276 to tow a light weight motor cycle trailer. I did take a look at your owner's manual and Toyota does not recommend towing anything with the Prius but it is ultimately up to you. If you decide to tow the motorcycle trailer you will need wiring, Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118505 to illuminate the trailer lights. You will also need a ball mount and ball. The recommended ball mount is part...
  view full answer...
• Towing Capacity and Hitch Recommendation for 2013 Honda Accord Coupe and CVT Transmission
  According to the online copy of your owner's manual, your 2013 Honda Accord Coupe has a maximum total trailer weight limit of 1,000 lbs. This includes the weight of the trailer, cargo, and everything inside or loaded on top of it. While CVT (continuous variable transmission) vehicles aren't ideal for trailer towing, as long as you adhere to the limits outlined in your owner's manual, you shouldn't have any problems. I suggest confirming this information on your hard copy of the owner's...
  view full answer...
• Does Trailer Hitch Recevier for 2021 Kia Seltos Require Drilling Into Frame
  No drilling into the frame of your 2021 Kia Seltos is required in order to install the trailer hitch receiver that fits it, the Curt Trailer Hitch Receiver # C65FR. This is a bolt-on installation and uses existing holes in your Kia's frame to install, which is why you don't have to drill. If you plan on doing some light towing with this hitch and your '21 Seltos, there are a few other parts you'll need, which are the following: - Vehicle Wiring Harness # C89KR - Curt Drawbar #...
  view full answer...
• Recommended Trailer Hitch Receiver and Towing Components for 2018 Toyota C-HR
  For your 2018 Toyota C-HR, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11490 along with the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118756 and the ball mount # C45521. I've attached a photo of the Draw-Tite # 24962 along with the Curt hitch to give you the visual comparison. The cleaner look is why I recommend the Curt hitch. The recommended parts above will give you a towing system when you add a hitch ball like # A-80 for...
  view full answer...
• Can a 2012 Ford Focus Tow a 600 lbs Total Jon Boat?
  According to your owners manual, your 2012 Ford Focus should never tow a trailer and is not equipped to tow. Using a trailer hitch like # C11158 is ideally to be used for accessories like a bike rack. Your vehicle has a payload rating between 935 and 1,055 lbs so if somehow you fit it inside your vehicle Ford would be okay with it. I personally would tow that trailer (but not anything larger than the jon boat) and you would be operating outside of Ford's warranty and recommendation. Based...
  view full answer...
• Can 2014 Ford Mustang be Used to Tow Motorcycle Trailer
  According to the online owner's manual for your 2014 Ford Mustang you can tow up to 1,000 lbs. So if you can find a trailer that weighs under 1,000 lbs with your motorcycle loaded you will be just fine. I recommend installing the Curt Trailer Hitch # C11210 on your Mustang because it has a collar around the receiver which can be used for more stability in certain applications. For wiring I recommend the T-One # 118487 because of how reliable we have found the Tekonsha wiring to be. Then...
  view full answer...

Do you have a question about this Hitch Pins and Clip?