CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers - Galvanized Steel - Qty 1

See what our Experts say about this CE Smith Boat Trailer Parts

• What Size Boards Need to Be Used with CE Smith V-Wing Bolster Bracket # CE26244G
  You really have to use either a 2x6 or a 2x8 with the CE Smith V-Wing Bolster Bracket # CE26244G that you referenced.
  view full answer...
• How Many V-Wing Bolster Brackets Should Be Used When My Bunks are 132 Inches
  I reached out to my contact at CE Smith, they are advising you to use one of the V-Wing bunk brackets # CE26244G on the back in the middle and one on the other end. Three brackets on each board.
  view full answer...
• Replacement V-Wing Bolster Bracket for Pontoon Boat
  What you sent in a picture of is a V-Wing bolster bracket like the # CE26244G that you referenced. These are slightly different from what you have that are 11 inches wide by 5 inches high. These are 15-1/2 inches wide by 6 inches tall which is pretty close. Also these are designed for 6 or 8 inch wide bunk boards. When you replace the boards you'll need to use either width and you'll be set. I attached a link to our return policy page also. We do not have anything like what's in your...
  view full answer...
  
• What Size Board Does CE26244G Bunk Board Bracket Fit
  You probably could make 2x4 bunks work on the CE Smith V-Wing Bolster Bracket # CE26244G but ideally you are going to want to use the taller boards like a 2x6 or 2x8.
  view full answer...
  
• Dimensions of V-Wing Bracket for Pontoon Boat Trailer
  We do have one V-wing bracket for pontoon boat trailers, the CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G though I wasn't quite sure what you were referencing in terms of a one inch lift so I added a photo for you which shows the dimensions of this bracket. It is a total of 15-1/2 inches long and measures 2-1/4 inches from the base to the bottom of the "V" and 6 inches tall at its highest point. The CE Smith V-Wing Bolster Bracket # CE26244G is made of galvanized...
  view full answer...
  
• Could the CE Smith Bolster Bracket part # CE26244G Be Used on Boat Lift
  Yes, if you wanted to use the # CE26244G on a boat lift you certainly could. You would need to supply the 6 or 8 inch wood bunks for use with this bracket though. I attached a review video for this for you to check out as well.
  view full answer...
• Can Pontoon V-Bracket be Used for Jet Ski Application
  The great thing about trailer boat parts is that they are universal and even though they may be designed for a certain purpose they can definitely be used for something else. I think using the CE Smith V-Wing Bolster Bracket # CE26244G is a great option for your jet ski. This bracket is designed for 2"x6" or 2"x8" bunk boards which it sounds like what you are planning to use.
  view full answer...
• Can CE Smith V-Wing Bolster Bracket be Used on Boat Lift
  The CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G referenced in your question is designed for boat trailers but can be used on your boat lift. You will just need to supply the 6 inch or 8 inch wide bunk boards for use with these brackets. These bolster brackets are designed specifically to support pontoon boat trailer bunks. They measure 15-1/2 inches long, 3 inches wide, and 6 inches tall. I have attached a short video demonstration on this product that you can...
  view full answer...
• What is the Distance from the Base to the Bottom of the V on the V-Wing Bracket # CE26244G
  The distance from the base to the bottom of the "V" on the CE Smith V-Wing Bolster Bracket part # CE26244G is 2-1/4". I have attached a photo of this measurement for you as well.
  view full answer...
  
• Weight Capacity of CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers CE26244G
  The CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G does not carry a specific weight rating. But since it is expressly intended for pontoon trailer use and is made from 1/8-inch-thick galvanized steel in typical use it will be over-rated for the application with plenty of safety margin. I suggest checking out the photos some of our customers have sent in to us showing their own installations. These appear on the item's page just below our own studio photos of this part.
  view full answer...
• Will Pontoon Boat Bolster Brackets # Work On Boat Lift Designed For A V-Hull Boat
  The CE Smith V-Wing Bolster Bracket, part # CE26244G we offer is designed to have either 2 X 6 or 2 X 8 boards mounted to them. They are made to sit under the pontoon on the boat and need to have a secure frame to be mounted to. With knowing that the lift was designed for V-hull boats, I recommend contacting the lift manufacturer to see if it can be modified to accommodate a pontoon boat. Due to the difference in construction of the boats the lift may not be able to work with the pontoon boat.
  view full answer...
• Availability of the CE Smith Bolster Bracket # CE10052-32G
  Actually the CE Smith Bolster Bracket for Pontoon Boat Trailers # CE10052-32G that you referenced is available as they have not been discontinued. We can ship you as many as you need.
  view full answer...
• Are CE Smith V-Wing Bolster Bracket Pontoon Trailers # CE26244G Strong Enough for a Pontoon Boat
  Yes, the CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G that you referenced would be a great option for bolster brackets for your pontoon boat trailer as that is exactly what this product was designed to do. The 1/8 inch galvanized steel construction of this bracket would make it strong enough for your pontoon.
  view full answer...
• Dimensions of the CE Smith V-Wing Bolster Bracket # CE26244G
  The CE Smith V-Wing Bolster Bracket # CE26244G that you referenced 15-1/2" long x 3" wide x 6" tall with mounting slot dimensions of 7-1/2" long x 1/2" wide. If you need further dimensions feel free to email me back with what you need and I'll get them for you.
  view full answer...
  
• Hole Dimensions of the CE Smith V-Wing Bolster Bracket # CE26244G
  I checked with CE Smith and they informed me that the larger holes on the bracket that connect to the bunks and the larger holes are .410 of an inch and the smaller holes are .313 of an inch. Check out the picture I attached for more dimensions.
  view full answer...
  
• What Hardware Should Be Used to Install a CE Smith V-Wing Bolster Bracket
  In order to mount the CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G you'll want to use use lag screws and a washer to attach the brackets; these aren't part of any hardware that comes with the brackets so you'll need to source them via your local hardware store. According to CE Smith they recommend that a bracket be installed at each frame cross member for maximum support. The brackets are best when installed with a 2x6 or 2x8 carpeted bunk boards laid flat.
  view full answer...
• Installation Of CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers CE26244G
  To install the CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers part # CE26244G you want to use lag screws and a washer to attach the brackets which you will need to source from a local hardware store according to CE so drilling will be required. They also recommend a bracket be installed at each frame cross member for maximum support. The brackets are best when installed with a 2x6 or 2x8 carpeted bunk boards laid flat.
  view full answer...
• V-Wing Bolster for Pontoon Boat That Can Hold 2x8 Bunks
  The CE Smith # CE26244G V-Wing Bolster bracket you'd looked at is the largest bracket of its type we offer. This being said, according to CE Smith, the bracket can easily handle 2x6 or 2x8 boards so it would work just fine for your application. You can see a product video featuring the # CE26244G bracket by clicking the provided link.
  view full answer...
• Will 12" Pontoons Work With The CE Smith V-Wing Bolster Bracket For Pontoon Trailers CE26244G?
  The CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers - Galvanized Steel - Qty 1 # CE26244G you were looking at is not listed for any specfic sizes of pontoons, and would work just fine with your 12" pontoons. The # CE26244G is designed for two 2"x6" or two 2"x8" bunk boards but does not included the mounting hardware so you will need to source it locally. I recommend using stainless steel hardware to keep it from rusting due to being in water. I included a video of the # CE26244G...
  view full answer...
• Can I Use Fiberglass Resin With Bunk Carpet On My Pontoon Boat Trailer
  It would be ok for your to cover them fiberglass resin and tyen cover. You will not having any problems doing so. The CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G will provide a strong mounting platform for your bunk boards. They have a galvanized steel construction which is sturdy and resists corrosion. I attached a review video link below.
  view full answer...
• Adding V-Wing Bolster Brackets To Cradle For 22-Ft Bennington Pontoon Boat
  Since you are planning on using the CE Smith V-Wing Bolster Brackets, part # CE26244G for a cradle, using boards that hang off the ends by 2-feet may give you plenty of support for your 22-ft pontoon boat. Adding the support to the middle crossbar will also ensure you have the most support. These cradles are made of 1/8-inch thick galvanized steel and come with a slotted mounting hole so you can adjust it when installing. If you need marine-grade carpeting for your bunk boards I recommend...
  view full answer...
• Can I use Trailer Bunk Boards for a Boat Lift?
  The CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G you referenced in your question is designed for boat trailers but can be used on your boat lift. These bolster brackets are designed specifically to support pontoon boat trailer bunks. Each bracket can hold up to two 2"x6" or 2"x8" bunk boards angled toward each other to provide support for one of the boat's pontoons. On both the right and left sides of the trailer, one bracket is mounted in the front and another in...
  view full answer...
• Using Bunk Rollers For a Kayak Ramp
  I do not see any reason why the CE Smith Roller Bunks # CE27710 would not work for your kayak ramp. The frame has a thick 3-5mil galvanized coating that will provide years of protection without rusting or corroding. The heavy duty rubber rollers will not damage your kayak when it is slid up or down the ramp. You will want to make sure that you can secure these properly. The CE Smith V-Wing Bolster Bracket # CE26244G may work to hold the rollers at the correct angle and width for your kayak.
  view full answer...
• Galvanized Steel Pontoon Trailer Replacement V-Wing for Bunk Boards
  The CE Smith Galvanized V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G does not include hardware. You can select galvanized hardware that will fit at your mounting point. I linked our page for galvanized u-bolt kits. This bracket is not intended for 2 x 4 bunk boards; it works with 2 x 6 or 2 x 8 boards to support your boat's pontoons. For 2 x 4 bunks you can use kit # CE10001G-4.
  view full answer...

Do you have a question about this Boat Trailer Part?