To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
This hitch slides automatically as you drive to give you 14" of additional clearance for tight turns. A wraparound jaw provides a smooth ride and a locking bar offers added security. Pivoting head allows easy hook up and helps to limit chucking.
Features:
Specs:
Note: This fifth-wheel trailer hitch is not compatible with Sidewinder or Revolution king pins. Do not use any device that changes the pivot point of your trailer's king pin with this hitch.
Most often used on trucks with 6-1/2' beds, a slider helps to eliminate clearance problems during slow-speed turns. When you are towing a fifth-wheel trailer, your hitch must be situated on the cab side of your truck's rear axle. However, at slow speeds you can use a slider to slide the fifth-wheel hitch (and the trailer) toward your truck's tailgate and past the rear axle, creating enough space between the cab of your truck and the trailer to permit less-restricted turning.
Normally, you'd have to get out of your truck and pull a lever to release the slider before every turn, but what if there was an automatic system? Imagine having 14" of extra clearance while towing your fifth-wheel trailer. Now imagine having this without needing get out of the truck to move your slider. The Demco Autoslide makes this fantasy a reality. The Autoslide automatically glides back smoothly when you make a sharp turn so you can maneuver effortlessly around tight corners within campsites and parking lots.
The base of the Autoslide has a built-in rack-and-pinion gear system that operates automatically. As your truck turns, the pinion in the base also turns. This activates the rack gear, which causes the rotational force of the truck to be converted into the linear sliding action of the hitch. So, when your truck makes a sharp, slow-speed turn, the gears inside the Autoslide force the hitch head to slide down toward your truck's tailgate in a smooth, controlled motion. This way, any time that your truck turns more than 10 to 15 degrees, the Autoslide will ensure that there is enough clearance for your trailer to complete the turn as well, and it will do so without any jerking or binding.
In order for the rack-and-pinion assembly to function as designed, the pin box must be stabilized on the hitch head. Normally in a fifth-wheel hitch, the king pin moves inside of the hitch head so that the trailer can turn. With the Autoslide, the king pin remains fixed inside of the jaws of the hitch and it is the hitch head itself that turns. This is thanks to the capture brackets on the sides of the head that brace the pin box from both sides to hold it in place on top of the hitch head. This is done to ensure that there is enough resistance within the hitch when your truck turns to properly activate the rack-and-pinion gear mechanism.
To stabilize your pin box on the hitch head, simply push the capture brackets up against your pin box once the trailer is coupled and tighten the outer bolts and the inner jam nuts. The Autoslide head and brackets will fit standard pin boxes that are between 12" and 14" wide. If you have a Glide Ride, Mor Ryde, Trailair Tri Glide, Rota Flex, Lippert Road Armor, or 5th Airborne pin box, you must install a special locking plate (sold separately) as well.
When you straighten your rig out again and your trailer moves back in line, the hitch head will rotate back to center and slide back toward the cab into the straight towing position.
The single-piece, strong wraparound jaw completely surrounds your trailer's king pin for 360 degrees of contact. This wraparound jaw provides a more secure connection than standard 2-piece jaws that close in on the king pin from the sides. The increased jaw-to-king-pin contact on the Autoslide offers tighter tolerances around the king pin, which minimizes both rattle and chucking, for a smooth, quiet ride.
A 3/4" solid steel locking bar spans the area in front of the jaw. This bar provides an added barrier of protection against accidental disconnection so you can have peace of mind that your trailer is secure. The locking bar is attached to the jaw and to the spring-loaded handle. The bar automatically locks when the jaw closes around your king pin.
The double pivoting, cushioned head improves your towing experience dramatically by helping to reduce jarring and unwanted noise. Built-in pins allow the hitch head to pivot back and forth and side to side. And hooking up is easy because the hitch head will automatically pivot to the proper angle when it comes into contact with your pin box.
Three polyurethane dampeners help to cushion the movement from the pivoting head and to reduce towing noise. Two of these dampeners are built into the head assembly to cushion the head's side-to-side pivoting. The third dampener cushions the back-and-forth motion and must be installed in the hitch prior to use. Installation of this third dampener is easy - simply press the dampener up into the pre-drilled hole underneath the hitch head.
Easy Installation
Included with the Autoslide hitch is a rail adapter that's specific to the Nissan Titan factory prep package. Just drop the adapter into the puck receivers built into your truck bed and lock them in place. Then you can position the pre-assembled hitch base in your bed and easily pin it to the rails. Just bolt on the side plates and attach the head to the hitch base, and you'll be ready to tow.
The side plates have 2 functions. They contain the feet that fit into the rails, and they allow you to raise or lower the hitch head to better match your pin box height. After you choose your desired height setting, simply bolt the side plates to the hitch base with the included hardware. Then attach the base to the rails with the included safety pins.
Clearance Formula for Short Bed Trucks
Use the formula below to ensure there will be enough space between your truck cab and trailer when executing a 90-degree turn.
(A+B) - C = Clearance
A = Distance from the center of fifth-wheel hitch jaw to truck cab
B = Length of Travel (14")
C = Width of trailer divided by 2 (to get half)
For example: If the distance from the center of the hitch to the cab is 36", 36" + 14" = 50". If your fifth-wheel trailer is 84" wide, take half (42"), then plug in: 50" - 42" = 8" of clearance.
Note: At least 4 inches of clearance is recommended to safely execute a 90-degree turn.
Alternate Instructions
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everybody. Andy here with etrailer.com. Let's take a look together at this Demco 5th Wheel Rail Adapter Now, this adapter is specifically designed to fit your 2016 and newer Nissan Titan XD with a 6.5 foot bed with the OEM integrated Gooseneck and then your 2017 to 2019 Nissan Titan XD with an eight foot bed, again with the OEM integrated gooseneck. Now, on custom fit parts such as this adapter, I do recommend taking advantage of our vehicle fit guide here at etrailer.com. Simply input the year, make, and model of your truck and our fit guide will confirm if this will work for you or if we have something comparable that will work for you. Now, this adapter is going to be perfect if you want to use your standard 5th wheel trailer hitch with your Titan XD truck's factory-installed underbed 5th wheel mounting kit.
This is going to let you use your 5th wheel trailer hitch that attaches to the standard above bed rails. However, I do wanna point out that this adapter will not work with the B&W Patriot sliding hitch. So just so you're aware of that. Now this is going to mount to the two OEM pucks. And then the center shaft that you see there, that's going to insert into the gooseneck ball hole in your Titan's bed.
So with this little bit closer underside view, hopefully you can see these pins here. Those pins are what's gonna drop into the the puck there, and then that center shaft is going to drop into that gooseneck ball hole. Now, this does use a ball bearing locking system. So right now I have it locked, but let me go ahead and unlock this. So this does include this thumbscrew with a washer.
So I'm gonna go ahead and remove that thumbscrew. And then if you just turn that slightly, taking another view close up, as you can see, hopefully those ball bearings are loose in there, so they're not secured. But after you have this dropped into place, into that puck system and into the gooseneck ball hole, you're just going to turn this latch like so. That's going to secure those ball bearings and make them to where they're not gonna be able to go back into the shaft. Insert the thumbscrew, tighten it down.
And then taking a closer look here, those balls are going to be secured into place. So hopefully you can see that. So this is made here in the USA of a rust-resistant black powder-coated steel construction. So this is very strong, very robust, very durable. This has a maximum capacity of 21,000 pounds. Instructions are included to guide you through the very simple installation process. However, I do wanna point out that even though this is going to be a very easy setup, a very easy install, this is a very heavy adapter. So you do wanna make sure that you have at least another person with you to help you lift this into your truck bed and then drop it into place. Well, I think that's gonna wrap up our look today. I do hope that our time together was helpful for you. Again, my name is Andy, thank you for joining me.
Do you have a question about this 5th Wheel Hitch?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.