...I have a 2019 Jayco SLX 212QB 21foot. I used to see an electric tongue jack that was direct wired but had a 7 way cable as backup. Do you still have one like that? If not, would relying on the truck...
...Looking for install instructions. Mainly looking for wiring setup requirements. Current electric jack has a 7 way plug for power. I assume Ill need a battery setup for this...
...Can this jack be used with single acting hydraulic pump? I dont have a pump on my trailer but I want a hydraulic jack like this since its more capable than electric or manual jacks usually...
Hello Jeremy, Yes, our etrailer jack #e55ZV will automatically stop and not over raise. If you check out the video that I attached you will see that Steven still has his finger pushing down the button after the jack stops. What kind of application…
...I want an electric jack for my utility trailer that works off my 7 pin truck connection. 3500 pounds is ok. Do you make an adaptor from 2 wire to 7 pin or do I need a 7 pin connector jack...
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Jacqueline! The Dexter Self-Contained Hydraulic Jack #DX72CR manual didn't have anything in it about a manual override, but in looking at the photos, the rubber plug on top of the cover should be where the manual override is located. Try…
The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…
...Hello, and thanks for getting in touch. The etrailer Electric Trailer Jacks # e55ZV and # e23ZV will hold up just fine in cold weather. The housing is designed to be water/weather resistant. It even...
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
...Hey Ross, thanks for reaching out. I believe we are working on a video for the etrailer Electric Trailer Jack # e74GV, but this is a fairly new product, so we have not had the chance to finish it yet...
Hello John, I was not able to find that information anywhere, luckily we have one on a trailer right outside. From the top of the mounting plate to the top of the jack is 20 1/4". What kind of trailer were you thinking about putting this on?
...I have a 2019 Jayco SLX 212QB 21foot. I used to see an electric tongue jack that was direct wired but had a 7 way cable as backup. Do you still have one like that? If not, would relying on the truck...
...Looking for install instructions. Mainly looking for wiring setup requirements. Current electric jack has a 7 way plug for power. I assume Ill need a battery setup for this...
...Can this jack be used with single acting hydraulic pump? I dont have a pump on my trailer but I want a hydraulic jack like this since its more capable than electric or manual jacks usually...
Hello Jeremy, Yes, our etrailer jack #e55ZV will automatically stop and not over raise. If you check out the video that I attached you will see that Steven still has his finger pushing down the button after the jack stops. What kind of application…
...I want an electric jack for my utility trailer that works off my 7 pin truck connection. 3500 pounds is ok. Do you make an adaptor from 2 wire to 7 pin or do I need a 7 pin connector jack...
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Jacqueline! The Dexter Self-Contained Hydraulic Jack #DX72CR manual didn't have anything in it about a manual override, but in looking at the photos, the rubber plug on top of the cover should be where the manual override is located. Try…
The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…
...Hello, and thanks for getting in touch. The etrailer Electric Trailer Jacks # e55ZV and # e23ZV will hold up just fine in cold weather. The housing is designed to be water/weather resistant. It even...
According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…
...Hey Ross, thanks for reaching out. I believe we are working on a video for the etrailer Electric Trailer Jack # e74GV, but this is a fairly new product, so we have not had the chance to finish it yet...
Hello John, I was not able to find that information anywhere, luckily we have one on a trailer right outside. From the top of the mounting plate to the top of the jack is 20 1/4". What kind of trailer were you thinking about putting this on?
Electric trailer jacks make hitching and unhitching a breeze. With features like memory settings and easy installation, they are perfect for trailers with solar setups or heavy tongue weights. Say goodbye to manual cranking and enjoy the convenience of automatic lifting with just a push of a button.
Electric jacks automate the lifting and lowering process, saving time and effort. With memory settings, you can quickly adjust to your preferred height, making it ideal for heavy trailers or those with solar power setups. Just press a button and focus on other tasks like securing safety chains.
Installation is straightforward, often requiring no welding. Some setups may need a bolt-on bracket for non-standard locations. Wiring can be connected directly to the battery if needed, ensuring a hassle-free upgrade even for those with limited technical skills.
Yes, electric jacks are perfect for solar-powered trailers. They integrate seamlessly with existing electrical systems, utilizing stored power efficiently. This makes them a smart choice for trailers with solar panels and battery banks, providing reliable performance without draining power.
Regular checks on wiring connections and ensuring the battery is charged are key. If the manual override is used, ensure the key and adapter are in good condition. Address any wiring color discrepancies to avoid confusion, especially with ground wires.
Electric jacks are designed to handle several thousand pounds of tongue weight effortlessly. They provide consistent lifting power, making them suitable for heavy-duty trailers. This reliability ensures smooth operation even under significant loads.
Filters
