Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
4" Long x 1-3/4" wide x 2-5/16" thick. Incandescent trailer light illuminates your license plate. Durable stainless steel mounting base. Stud mount to trailer - hardware not included. 1-Wire design. (1) 194 Bulb.
Features:
Specs:
Manufacturer Cross Reference
Light will work as an exact replacement for:
Peterson # M436
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our enclosed trailer, we're going to be installing the Optronics Ear Mount Trailer License Plate Light with the plastic housing and gray in color, Part Number LP51CB. Depending on your trailer will depend on how much of the interior you may need to take apart to gain access to the wiring to install the new trailer license plate light. We've also gone ahead and removed any of the old license plate light that was still on the trailer. Now that we have our surface ready to install our new license plate light, we'll go ahead and feed the wire through the hole so that the wire goes into the trailer itself. We'll go ahead and hold our light up into place and then mark the two holes. We'll then set the light aside for now. Next we're going to take two self tapping screws and pre-drill the holes into the trailer.
We'll then back each of the screws out and then put the light up into place, feeding the wire through a center hole allowing it to go into the internal part of the trailer. Then we'll go ahead and take our ratchet and put our screws back in, holding the light in place. Now in our case we needed to remove a couple pieces of internal trim to gain access to the wiring to install the new light. Now that the trim is out of the way, you could see here that we have our wire hanging down. It's part of the running light circuit. Now that that's done, we can go ahead and connect our wiring.
We use a simple butt connector here to connect our running light wire in with the wire coming out of the back of the license plate light. The butt connector that we'll be using today is Part Number DW05714. Once our connection's made, we'll go ahead and wrap it with some electrical tape to give it a little more protection. Now we'll go ahead and test the light before we put our interior back together. As you can see here, with our running light circuit on on the trailer, our license plate light comes on. Now that we've tested it, you can go ahead and put your interior back together.
Again depending on your exact model of trailer will determine what you have to reinstall. In our case, it's a couple pieces of trim. Once our trim is back in place, we can go ahead and close the door up and that'll complete the installation of the Optronics Ear Mount Trailer License Plate Light, Part Number LP51CB. .
Average Customer Rating: 4.8 out of 5 stars (156 Customer Reviews)
4" Long x 1-3/4" wide x 2-5/16" thick. Incandescent trailer light illuminates your license plate. Durable stainless steel mounting base. Stud mount to trailer - hardware not included. 1-Wire design. (1) 194 Bulb.Perfect fit/replacement. Easy to install. Looks and works great!
EXACTLY what I needed!
Always great products and easy to order.
This was the perfect light for my trailer License Plate. It has not failed since installation 1 year and lots of miles!!
George N.
1/5/2023
Trailer Lights still shining bright. Benn a loooong time and more miles!!
QUICK EASY ON TIME WILL BE ORDERING BRAKES NEXT THANK YOU
works great
Just as described. I am very happy with the light. It works very nicely on my custom Beetle.
Great replacement for the price. Fast shipping and delivered in a couple of days. Thanks!
I have a 2010 mission trailer for my snowmobile and noticed recently my marker plate light was out,the unit needed to be replaced,ended up findind an exact match here on ETRAILER.COM Thanks.. you guys never disappoint
Perfect fit using the same mounting holes for my early 90’s Circle J Arrow.
selection and service have been great. this is my go site for trailer parts and accessories.
Easy to install and works great.
Got the parts I ordered in Excellent condition. Installed the Roof Vent with ease. I did have one little challenge. I disposed of the box the Roof Vent came in. It is now time to mount the license plate light. I could not find find the light anywhere. Well, I was getting ready to call E-trailers about the missing light, when I decided to get the box out of the trash. Well, it was wrapped up in the paper. Next time I will look a little closer.
Very pleased with with the products from E-trailer. They got my business and will tell my friends about E-trailer.
I'm in the process of bringing my '84 tilt bed trailer back to decent condition and needed lights, etc. I went to the website and was able to find everything I was looking for. Ordering was easy and shipping was scheduled to arrive on July 6th. To my surprise, it showed up on the 2nd, in good condition and was exactly what I was looking for. Thank you for the excellent service.
It's exactly what I needed and was received soon than I was expecting. Won't hesitate to buy again from etrailer.com. Keep up the good work.
Jeff
9/21/2016
So far so good. Thanks for the follow up.
Worked ok. It's not an exact fit like the other lights I bought from etrailer. My old light fixture had a metal frame that went around the whole license plate area; this one didn't fit exactly. Nothing wrong with this light, just a slightly different design. I made it work rather than returning it.
This light perfectly matched the license plate light that was damaged on our horse trailer. Since only the plastice housing and the bulb were broken, we were able to only replaced these parts. Easy-peasy repair. We will keep the ear mount base as a spare.
I purchased this to replace the license plate light cover that some kids broke playing around behind my trailer. I had problems removong the old baseplate/light fitting so I just used the lens and back cover and it fit perfectly. This was on my 2007 12x6 Haulmark cargo trailer and fit perfectly!
Light was exact replacement for my Atlas Trailer. Received the light very quickly and the entire ordering experience was pleasant and expeditiously handled
I just bought a 2006 goose neck trailer that needed some minor repair. Wanted to match existing good parts. This was an exact replacement on this old LONGHORN trailer.
I haven't had time to install it yet, but the license plate light was exactly what I need as a replacement for the horse mangled one on the trailer. Order was received on time and good quality.
Just what we needed, and then some. In actuality, all we needed was the lease cover and not the entire unit. However, it was what we needed to replace the lense cover to our trailer light. Thank you! Shipping very prompt.
I have done business with this company several times and always have fast delivery and receive a good product.
Got the product at noon and installed onto my trailer during my lunch break. Only negative is there were no instructions shipped with it. Luckily I knew how to wire it up.
Just what I needed to replace the rusty original licence plate light on my Sno-Pro trailer. Only thing, I wish the wire was a bit longer.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Carlo
11/7/2023
The license plate light seems to be working fine. Im pleased with the product.