Incandescent Trailer Fender Light w/ Reflector - 2 Bulbs - Red and Amber Lens - Driver Side

Ask the Experts about this Optronics Trailer Lights

• Replacement Fender Light Lenses for a United Trailer
  Sorry about your lenses being damaged. The good news is that replacement lenses are available for the Fender Clearance Light, part # BA44FNL. The amber lens is part # A44AB, the red lens is part # A44RB.
  view full answer...
• Will Fender Clearance Trailer Lights Work as Turn Signals?
  You can use the pre-wired Fender Clearance Trailer Light # BA44FNL (left) and # BA44FNR (right) as turn signals. They come with a ground wire and power wire so you would just need to wire them to your turn signal power wires to give your fenders the turn signals you want. I've added a link to a help article on trailer wiring for you to take a look at as well.
  view full answer...
• Availability of LED Version of Optronics Left Fender Clearance Trailer Light # BA44FNL
  The closest match for an LED version of the Left Fender Clearance Trailer Light # BA44FNL referenced in your question is the Optronics Clearance Light Assembly # MCL12ARLB for the driver side and # MCL12ARRB for the passenger side. These are pre-wired LED light assemblies that will mount on the fender to mark the widest point of your trailer. I have attached a demonstration and installation video on this assembly so you can see exactly what they look like and how they work.
  view full answer...
• Can Lenses on Left Fender Clearance Trailer Light # BA44FNL be Switched to Use on Right Side
  Yes, you can swap the lenses on the Left Fender Clearance Trailer Light # BA44FNL, although we do have the Right Fender Trailer Light # BA44FNR as well. I have attached review and installation videos for you to check out.
  view full answer...
• Dimensions of the Left Fender Clearance Trailer Light # BA44FNL For Direct Replacement
  I went out to the warehouse and pulled one of the Left Fender Clearance Lights, # BA44FNL, to measure. I get 8-1/4 inches overall length and 3-3/16 inches overall width. The manufacturer must have changed dimensions on these parts at some point. I attached a photo and added dimensions to it so you can be sure we are measuring the same.
  view full answer...
• Amber and Red LED Clearance Light Recommendation for a Trailer Fender
  The closest thing we offer to the # BA44FNL and the # BA44FNR in LED is the part # MCL12ARRB and the # MCL12ARLB. I attached an install and review video for these lights for you to check out as well.
  view full answer...
• Availability of Amber and Red LED Clearance Light for Trailer Fender
  The closest lights we offer to the # BA44FNL and the # BA44FNR in LED is part # MCL12ARRB and # MCL12ARLB. I attached an install and review video for these lights for you to check out as well.
  view full answer...
• Trailer Fender with Lights for Trailer with 14 Inch Wheels
  We have a lot of fenders that will fit 14 inch wheels, see link. Even though they do not come with lights you can add lights to them. For example take a look at these fender lights with both red and amber lights: # MCL12ARLB and # MCL12ARRB # BA44FNR and # BA44FNL # DG52444VP and # DG52443VP # 54201-013 and # 54201-011
  view full answer...
• Recommended Clearance Light For Enclosed Trailer Fenders
  We have the following options that are intended to be clearance lights but could be wired to be used as turn signals: LED Clearance Light Assembly for Trailer Fender - Trailers over 80" Wide - Driver Side # MCL12ARLB and passenger side # MCL12ARRB. Left Fender Clearance Trailer Light, Prewired - Amber and Red # BA44FNL and right # BA44FNR. LED Trailer Fender Clearance Light - Submersible - 2 Diodes - Amber/Red - Driver or Passenger Side # MCL180ARB. Bargman Fender Clearance/Side...
  view full answer...
• Adding Lights to CE Smith Fenders
  There aren't fenders available that have cutouts for side marker lights, but there is a way to add lights to the CE Smith Single Axle Trailer Fenders with Top and Side Steps # CE19502-2. You could very carefully cut the fenders because they are plastic, or you can mount lights on top with the Trailer Fender Light with Reflector - Driver Side # BA44FNL and Passenger Side # BA44FNR. I have added links to video reviews for you to check out as well.
  view full answer...
• Fulton Plastic Fender # F00584 and Fender Light Recommendation for Right and Left Side of Trailer
  These Fulton Plastic Fender with Top Step - Black - 14 inch Tires, part # F00854, can be used on the left or right side of the trailer. That is why there is not a left or right side fender you can pick from on our site. You would need to order 2 of them if you need fenders for both sides of your trailer. These fenders do not come with lights pre-installed on them. You would need a Right Fender Clearance Trailer Light, Prewired - Amber and Red, part # BA44FNR, and a Left Fender Clearance...
  view full answer...
• Plastic Fender And Lights Recommendation For Tow Dolly
  We do offer plastic fenders that may work for your tow dolly but the fenders do not come with lights pre-installed on them. The fenders we offer are for single axle trailers and we have a couple of sizes available. They will fit for both the left and right side of the trailer. For 8 to 12 inch wheels I recommend part # F008541. These have a top step, and have a 300 lb weight capacity. For 13 inch tires I recommend part # F008543. Since these do not come with lights pre-installed...
  view full answer...
• Replacement Red/Amber Fender-Mount Tail Light for Aluma Motorcycle Trailer
  We do offer all sorts of trailer lighting, including fender-mount types such as # BA44FNL and # BA44FNR which are combination red/amber lights. We also have # MCL61ARB. These and all other red/amber lights are shown on the linked page. If you cannot find the correct item by reviewing the page please feel free to send us a photo or two of your trailer and lights and we can try to match it.
  view full answer...
• Can Holes be Cut for Lights in Fulton Plastic Trailer Fenders
  You could likely cut out light holes on fender # F008575 if you wanted to. Using a rotary tool would make it quick and easy. Or you could mount left fender light # BA44FNL and right fender light # BA44FNR on the fenders. Fenders with pre-cut light holes are not available.
  view full answer...
• Dimensions Of Optronics Fender Trailer Clearance Light Assembles For Trailers Over 80 Inches Wide
  I pulled the 2 trailer lights you asked about so that I could take some measurements you wanted. I have attached a couple of photos with the dimensions noted on the photo. Part # BA65ARRB measures 5-7/16 inches long and 3-3/16 inches wide, and is used for the right side of the trailer. For the left side you would need part # BA65ARLB. The # BA44FNL measures 3-1/16 inches wide and 4-13/16 inches long without the mounting hole flange, and 5-3/8 inches long when measuring with the...
  view full answer...
• Fender Compatible With 13 Inch Wheels On Shorelander Trailer Carrying 18 Foot SEA-ARC Boat
  I have provided a link of the fenders that will work with your existing trailer and a 13 inch tire size. Several of these fenders provide areas that are intended to mount lights but none have lights that are included with the fenders. For your trailer I recommend the Fulton Single Axle Trailer Fender with Top and Side Steps, this comes in 3 colors white # F008573, silver # F008593, and black # F008583. The dimensions of this fender are 9 inches wide by 40 inches long by 12 inches tall....
  view full answer...
• Can Wire Cover for Right Fender Clearance Trailer Light be Trimmed to Fit a Fender
  The little tail piece that sticks out is meant to cover and protect the wiring of light # BA44FNR and is therefore not structurally necessary for mounting the light. So you could trim it down as needed. I have linked a video review of the light for you. The matching left fender light is # BA44FNL. I have included a picture that shows the over 80 inch requirements for trailers for you. You will need rear clearance lamps, rear identification lamps, and front clearance lamps. The location...
  view full answer...
• Replacement Shorelander Trailer Fender and Light Kit Recommendation
  The Fulton Single Axle Trailer Fender part # F008583 should fit your Shorelandr trailer, but it does not come with lights. For the Fulton plastic fenders we recommend the Left Fender Clearance Trailer Light # BA44FNL and the Right Fender Clearance Trailer Light # BA44FNR.
  view full answer...
• Replacing Shorelander Fenders with Marker Lights
  The brackets we recommend for the plastic fenders are the # CE26098G-2. Don't worry, drilling a hole into the fender for the bracket to mount to your trailer will not hurt the structural integrity of the Fulton Fenders # F008584-2 you were looking at. If you are also in need of an inexpensive marker light, I recommend the Optronics Prewired Fender Ligth # BA44FNR for the right side and the # BA44FNL for the left side.
  view full answer...
• Trailer Fender with Lights Recommendation
  You could likely cut out light holes on fender # F008575 if you wanted to. Using a rotary tool would make it quick and easy. Or you could mount left fender light # BA44FNL and right fender light # BA44FNR on the fenders. Fenders with pre-cut light holes are not available from us.
  view full answer...
• Removing Lenses of Optronics Fender Light and Replacing Bulbs with LEDs
  The lens of # BA44FNR and # BA44FNL should pop off if you take a small flat head screw driver and pry it off. Unfortunately, we don't have any videos or instructions that show the removal. For replacement LED bulbs you can use # P340194A-360.
  view full answer...
• Replacement Optronics Fender-Mount Red/Amber Tail/Clearance Light for Charmac Cargo Trailer
  I reviewed quite a few photos of various Charmac cargo trailers and while I found some with external fenders I did not find any shown with lights installed. However, we do offer a lot of combination red/amber trailer lights and all are shown on the page I linked for you. Among these are fender-mount lights # MCL67ARB, # MCL12ARLB, # BA44FNR and # BA44FNL. There are others too on the linked page. If none of these is a correct replacement you can submit a photo .
  view full answer...
• Which Optronics Trailer Lights Accept Replacement Red Lens A44RB
  The Optronics Replacement Red Lens # A44RB is a fit for two different series of their trailer lights, the MC44 series and the BA44 series. This lens also fits your GloBrite 117R according to my contact at Optronics. The entire light assembly in the MC44 series is part # MC44RB and in the BA44 series it is parts # BA44FNR and # BA44FNL.
  view full answer...
• White Plastic Fender Recommendation for a Shorelandr Trailer
  The Fulton Single Axle Trailer Fender part # F008573 should fit your Shorelandr trailer, but it does not come with lights. For the Fulton plastic fenders we recommend the Left Fender Clearance Trailer Light # BA44FNL and the Right Fender Clearance Trailer Light # BA44FNR.
  view full answer...
• Why Are Some Trailer Clearance Lights Both Red & Amber?
  Some clearance lights like the Optronics Thinline LED Trailer Fender Light for Trailers Over 80" Wide - 10 Diodes - Amber/Red # MCL65ARB for example have both the amber and red lens because they are designed to be mounted on a part of the trailer like a fender that sticks out from the side of the trailer. If a light shines both front and back, then the clearance light facing the rear has to be red where a light facing forward needs to be amber. This is based on DOT requirements. This...
  view full answer...
• Marker Light Recommendations for Fulton Plastic Fenders
  For the Fulton plastic fenders we recommend the Left Fender Clearance Trailer Light # BA44FNL and the Right Fender Clearance Trailer Light # BA44FNR.
  view full answer...
• Recommended Mounting Hardware For Trailer Lights
  I recommend using self tapping screws to install the Oblong Trailer Clearance, Side Marker Light, 1 Wire - Amber # MC68AB, the Right Fender Clearance Trailer Light, Prewired - Amber and Red # BA44FNR or # BA44FNL, and the Trailer License Plate Light with Housing and Mounting Bracket - Clear Lens - Black Base # LP81BB. For these installations you can use Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc # FA1131822, which is corrosion resistant and has a hex-washer-head less likely to strip.
  view full answer...
• Fender Light Kit that Has Amber and Red Lights On Top of Fender
  We do have fender light kits that are very similar to the ones you sent in a picture of. For the left hand side we have the part # BA44FNL and for the right side we have the part # BA44FNR which would work well for you.
  view full answer...
• Trailer Jack Caster Wheel and Adding Turn Signals and/or Marker Lights to Trailer Fenders
  Caster wheel # BDCP555 could potentially fit your current jack. It is designed to fit 2 inch diameter jack tubes. The wheel is rated for 1,500 pounds so if the jack is rated higher you will still be limited to 1,500 pounds. Trailers in the US have combined brake lights and turn signals. If you want to have separate amber turn signals on the fenders then that will require some additional parts. The left turn/brake light wire on the trailer connector will need to be split with one of the...
  view full answer...