Replacement License Plate Light With Single Black Wire

Question

Question:

Do you good folks sell a trailer license plate light FIXTURE with a single black wire? The original light fixture on mine is missing the lens, so I thought it best to merely try and replace the existing unit with a new one. Again, it only has ONE black wire. Thank you for your time

asked by: Ray C

0

Expert Reply:

For a license plate light with a single black wire you can choose from the following:

-Optronics Trailer License Plate Light - Incandescent - Gray Housing - Clear Lens # LP51CB

-Trailer License Plate Light w/ Chrome Housing - Incandescent - Rectangle - Clear Lens # LP41CB

-Trailer License Plate Light, Heavy Duty Armored Steel - Chrome Plated # LP21CB

-Optronics Snap-In Mini License Plate Light - Incandescent - Round - Chrome Plated - Clear Lens # LP11CB

All of these have the single wire for power and ground through the mounting hardware. There are some other styles if you don't mind running a separate ground wire for the light. I have attached a link below to all of our license plate lights for your reference.

expert reply by: Robin H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 12

Hey Dave, for a saltwater boat trailer, powder-coated wheels wouldn't be my first choice, but they can still last quite a while if you're good about rinsing them thoroughly after each launch and sealing any chips or cracks in the finish as…

view full answer...

Replacement License Plate Light With Single Black Wire

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching