Optronics Incandescent Trailer Clearance and Side Marker Light - Submersible - 2 Bulbs - Red Lens

Ask the Experts about this Optronics Trailer Lights

Do you have a question about this Trailer Light?

• Replacement Oval Amber Trailer Clearance Light Lens
  
• Thanks for the picture! Because of that I was able to determine that you need the part # A66AB.
  view full answer...


• Clearance Light Recommendation that are 3-7/8 inch x 1-1/4 inch x 7/8 inch
  
• I believe the Clearance Light part # MC65RB would be the correct light for you. The difference in length is about .1 of an inch which would be close enough. Especially since these look exactly like what you have and the other dimensions match up. The amber version of this is part # MC65AB. Fort the amber/red version you would want # MC65ARB.
  view full answer...


• Can I Use Optronics LED Light # MCL75RB in the Same Base as Light # MC65RB
  
• Yes, both the Optronics lights # MC65RB and MCL75RB use the same mounting base, so the # MCL75RB lights will snap into your old bases. You will then need to wire in the lights, with a power and ground connection. Part # MCL75RB is a sealed LED light light and will burn brighter but draw less power than part # MC65RB. Both lights use either base # A65PB or # A67CB. See the video that I shot showing both lights.
  view full answer...


• How To Order Trailer Lights
  
• To order trailer lights you will want to order by part number on your lights or by the size of the light you will need. The SAE stands for the Society of Automotive Engineers and the 97 DOT stands for the Department Of Transportation. These part numbers are usually on the lenses of most all trailer lights. You will want to get a Brand name (Bargman, Peterson, Wesbar) and the part number (40-38-001, 154R, 221902) that is on your light to be able to get the correct light for your trailer....
  view full answer...


• Comparing Black Bracket and Single Wire Plug A65PB and Plug n Go Bracket A65PBPG
  
• For the Black Bracket and Single Wire Plug, # A65PB, the plug on the end of the one wire is different than that on # A65PBPG. The plug n go style on # A65PBPG is easier to attach to the MC65 series of lights, like # MC65RB, because the cable is molded around the connector. This also covers any exposed wires that would normally be present like on # A65PB.
  view full answer...


• Replacement Boat Trailer Clearance Light with SAE P2 91 DOT on the Lens
  
• The number on the lens that you see is the lens rating, not a part number so it is difficult to go by that number. There might be a part number on the back of the light housing. Otherwise it would be easiest to go by the dimensions of the light. For example light # A91RB does have the same lens rating. It would use a base such as # A91BB and wiring harness # A91LW for the power wire.
  view full answer...


• Running Lights for 2014 Shorelander Trailer
  
• It doesn't look like we have an exact match for the clearance light on your trailer, but we have several similarly shaped ones that could work. If you measure the dimensions of your light and then check out the link I attached to the right you will see a list of all of the submersible, rectangle clearance lights we offer. If you select the dimension closest to your light has from the list on the left you will see the lights that would fit the best.
  view full answer...


• Replacing Optronics Thin Line Incandescent Trailer Light with Thin Line LED Trailer Light
  
• You are exactly right. Changing out your # MC65RB incandescent lights for new # MCL75RB lights will simply require removing the existing light and snapping a new light into the same housing. Both of these lights use the # A65PB bracket. If any of the brackets on your trailer need replaced you can use the # A65PB as a replacement, but the LED lights will not require any different base than the incandescent lights. I have attached an installation video of the # MCL75RB light for you.
  view full answer...


• Recommended LED Clearance Light that is Red and Amber
  
• The Optronics LED clearance light that is similar to # MC65RB, but will be amber and red, is the Optronics LED clearance light # MCL65ARB. This light is sealed, waterproof and is a surface mount. The dimensions are 3-15/16 inch length by 1-1/4 inch width by 7/8 inch deep. You will need a bracket and plug like # A65PB to complete the installation of the Optronics LED trailer light # MCL65ARB. Another option you may like is the LED clearance/marker light with a bracket and wire # MCL67ARB....
  view full answer...


• Recommended Amber, Red, And Clear Lens LED Clearance Lights For Karavan Boat Trailer
  
• The clearance lights we offer are not exactly the size you mentioned but these may work well for your trailer. I recommend part # AL82AB for the amber lights. These are LED lights and are submersible. These measure 2-1/2 inches long and 1-3/16 inches wide and 7/8 inch deep. For a red clearance light I recommend part # AL91RB. The clearance lights with a clear lens has amber colored diodes. We do not have a clear I recommend part # AL91CAB. All three of these lights have the...
  view full answer...


• Availability of Replacement Lens for Magnetic Tow Lights
  
• I compared the picture of the lights you have to the magnetic tow lights we carry and it looks like you have the Roadmaster Magnetic lights part # RM-2120. Which I spoke to my contact at Roadmaster and he said that any replacement lens with a 4-1/4 inch overall diameter that snaps onto the light housing would work like the part # A24RB.
  view full answer...


• Availability of LED Version of Optronics Thinline LED Trailer Clearance Light MC65RB
  
• The # MCL65RB is an LED version of the # MC65RB that you referenced in your question. The LED version is brighter than the incandescent as well. I attached a review video for this LED light for you to check out as well.
  view full answer...


• What is the Difference Between a P2 Rated Light and a PC Rated Light
  
• We actually have a handy help article, linked to the right for you, that explains this and other helpful information on trailer lights. Below is an excerpt: The light beam emitted from a P2 or P3 light spreads out 45 degrees to each side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side of the trailer. When mounted square to the front, sides, or back of a trailer, this kind of light provides...
  view full answer...


• Troubleshooting Installation of Side Marker Lights on a 2003 Silver Star Horse Trailer
  
• I have a solution for you but we do not have an exact replacement for the PM154 that you referenced. I saw that you purchased # MC65RB and the proper base bracket for these lights is # A65PB if you would like black or # A67CB if you wanted a chrome base.
  view full answer...


• Troubleshooting 5th Wheel Trailer Clearance Lights Blinking with the Turn Signals
  
• When using the brake and turn signal at the same time, you are drawing more power then just with running lights. Since some of the LEDs blink, they may inadvertently be attached to the turn signal wire on the trailer. Most trailers have one wire that carries both turn signal and brake light functions and one wire that carries running lights. I would check to make sure the correct wire is run to the new clearance lights. An LED clearance light like # MC65RB will have two terminals or wires....
  view full answer...


• What Screws Fit Black Bracket and Single Wire Plug for Thin Line Series Trailer Lights # A65PB
  
• The back of the lights that go with the Black Bracket and Single Wire Plug for Thin Line Series Trailer Clearance and Side Marker Lights, # A65PB, have a recessed area over the mounting holes. Take a look at # MC65RB, and click on the third picture to see the recessed area. I went out to the warehouse and pulled both parts to measure. There is a space of 3/16 inches between the bottom of that recessed area and the base of the bracket. The screw head would have to be 3/16 inches tall...
  view full answer...


• What Is The Current Draw For Optronics Sealed Side Marker Light
  
• I spoke with my contact at Optronics about the Sealed Side Marker Light, part # MC65RB. They told me the current draw for this 12 V light is .6 amperes. This is a sealed, waterproof light and measures 3-15/16 x 1-1/4 x 7/8 inches. The light mounts on 3 inch centers. The mounting hardware, part # A65PB is sold separately.
  view full answer...


• Lights Needed on 12 Foot Long x 83 Inches Wide Dump Trailer
  
• I can certainly help you find all of the parts needed to rewire your dump trailer and we do have a lighting kit that will work for you. However we do not have any kind of plug-and-play rewiring kit. The taillight kit I recommend for you is the Optronics Waterproof, Over 80 Inch LED Trailer Light Kit with 25 Foot Wiring Harness # TLL16RK. This kit includes 2 red LED taillights with the functions needed for trailers over 80 inches wide. The included wiring harness has 25 feet of wire...
  view full answer...


• Replacement LED-Type Surface-Mount Trailer Lights
  
• We offer high-efficiency LED-type trailer lights in various sizes, colors and shapes. The linked page will let you sort the results by clicking on the attributes you prefer. The results shown are already filtered to show only surface-mount red color lights like the Optronics # MC65RB. You can use the additional filters on the page to select the size and shape you need. Please feel free to submit a photo of your trailer lights if you need further assistance finding suitable replacements.
  view full answer...

Do you have a question about this Trailer Light?