Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
(395 reviews)
Price: $166.31
In Stock
Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
Item # 23-26-27
Our Price: $166.31
This item qualifies for Free Shipping
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (395)
- Q & A (0)
- Photos
Dexter Trailer Brakes - 23-26-27
- Electric Drum Brakes
- 3500 lbs Axle
- 10 x 2-1/4 Inch Drum
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Standard Grade
- Dexter
Whether you're replacing trailer brakes or installing some on a new brake axle, these are easy to work with from start to stop. 10" x 2-1/4" Assemblies fit 14" to 15" wheels. 4-Bolt pattern backing plate. Made in the USA.
Features:
- Easier to install and gives you more control than hydraulic brakes
- Requires only an electric brake controller (sold separately) - no actuator or hydraulic lines needed
- Periodic manual adjustment required
- Can be done in minutes
- Long-lasting brake pads offer excellent braking torque
- Fully bonded to shoes for more consistent braking compared to riveted pads
- Adjuster plugs (included) protect internal components from dirt, grime, and road debris
- Left-hand (driver's-side) and right-hand (passenger's-side) brake assemblies included
- Includes mounting hardware
- Made in the USA
Specs:
- Application: most standard hub-and-drum assemblies, including etrailer, Dexter, and Lippert (LCI)
- Dimensions: 10" diameter x 2-1/4" wide
- Mounting flange bolt pattern: 4 bolt
- Mounting flange bolt hole distance: 2-7/8" apart on center
- Wheel size: 14", 14-1/2", and 15"
- Axle rating: 3,500 lbs
- Limited 5-year warranty
Quick Tip: There's really not a whole lot to getting new drum brakes. If you've confirmed that all of the specs listed above line up with what you need for your trailer, you can be pretty sure these will work for you.
How to Manually Adjust Trailer Brakes
The more miles you put on your trailer, the more your brake pads will wear down. As they lose contact with the drum, stopping distances get longer and longer. To keep your brakes working great, it's important to adjust them pretty routinely. For this job, grab a floor jack and either a brake adjustment tool (sold separately) or just a standard flathead screwdriver.
Jack up your trailer enough to get the wheel(s) off the ground. Remove the adjuster plugs from the backing plate on the brake, and insert the flat end of the tool through the back of the assembly.
Push in on the star gear and lift it up. Keep doing this until the brake pads catch on your drum. When you can't spin your wheel by hand anymore, back the gear off by about 10 clicks by pushing down on the star gear. Does the wheel now spin freely (even if it sounds like the brake pads drag slightly on the drum)? Great! Then you're all done with that one and ready to adjust the rest.
How to Break In New Brakes
After you get these brakes installed and adjusted, you'll need to break them in. First, find a long stretch of road or a big, empty parking lot. Once you're there, set your brake controller to its maximum setting and get moving. Speed up to about 40 mph and brake to slow to about 20 mph. Repeat this 15-30 times. The goal is to get the brake shoes and magnet properly seated into your drum. You'll know you've done that when it feels less jerky (and more consistent) each time you apply the brakes.
Note: The brakes will be very hot after doing this, so after every 10 stops you'll want to wait about 10 minutes to let the brakes cool off before continuing. If you don't, you might cook and crack the pad material.
23-26 Dexter Electric Brake Assembly - LH - Driver Side - 10" x 2-1/4" - Manual Adjust - 3,500 lbs
23-27 Dexter Electric Brake Assembly - RH - Passenger Side - 10" x 2-1/4" - Manual Adjust - 3,500 lbs
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K - 23-26-27
Average Customer Rating: 4.8 out of 5 stars (395 Customer Reviews)
Whether you're replacing trailer brakes or installing some on a new brake axle, these are easy to work with from start to stop. 10" x 2-1/4" Assemblies fit 14" to 15" wheels. 4-Bolt pattern backing plate. Made in the USA.by: Paul11/08/2023
The brake parts were all correct for my application and installation was straightforward with minimal tools needed. I did take the extra step of soldering the wire connections because that is the best way to do it IMO.
Stephen at etrailer was very helpful. He made sure I had all the right parts for my application. and they were on their way very quickly.
I will say that I tried to use my local dealer first because I like to support local businesses, but unfortunately, they were having trouble finding the right parts for my trailer. When we did find them, they were 50% more expensive for the exact same parts that etrailer supplied. I would also have had to drive 80 miles round trip to get them.
The reason for the 4-star rating is because of shipping/packing. The parts were heavy in large boxes with no packing material to hold them in place. Two of the hub sets were out of their boxes and there was a crushed grease cap. So, better packing to keep things in place in the boxes or use a smaller box would be nice.
I attached a few pics of before and after also tmy very worn hubs. You can see that eh armature is worn down to the studs and the magnets are starting to show the coils. It was time. Also a short video or timelapse that I titled, Trailer Brakes in 18 seconds
by: Phil03/18/2023
My first time ordering from trailer, and I will definitely go back to them in the future. George J let me know when my shipment was on the way. Carol C. let me know it had been delivered. It came three days early! Their customer service has been outstanding and I am grateful. I needed to replace some parts in my electric brakes on my 17' Casita SD, which had failed state inspection in Virginia. The dealer wanted $400 to replace the magnets. I went with a right and left wheel assembly kit made by Dexter, the company that made my axle. New everything! Not messing around. The good: Just four nuts/ bolts! The bad: two of those nuts on each assembly required more than wrenches to remove them. Be prepared! Have a plan! The two behind the swing arm can be hard to reach with a socket. And two of those broke free from the brake assembly plate, so they just spin. I had to grind the head of the studs off with an angle grinder, after removing the brake shoes. See photo. After removal challenges, assembly was easy. Just four bolts and two wires! I reassembled with an anti seize compound on the threaded studs, so that when I have to do it again, hopefully the nut's are not frozen on the studs. Etrailer's service was awesome and their prices were the best as well. I'm a believer and will go with them again. Excellent transaction and support! Oh yeah... my packages arrived in new boxes and in perfect, ready to install condition. No issues with my red at all. Give them a try!
by: 01/18/2024
Spring tensioner assembly immediately broke in my driver side drum. Im having to mail back the entire assembly on my own dime. Dexter service is nonexistent, had to go through etrailer for the warranty help. Ended up buying a whole new drum assembly because i need it asap, instead of waiting weeks for the warranty to get figured out. Very annoyed.
by: Otis H04/07/2023
Website is very easy to navigate. Order went smooth and delivery was very quick. Parts seem to be high quality at a reasonable price. Very happy all around. I highly recommend e-trailer.
Otis H.
4/9/2024
After a year, my-trailer brakes are working great. I’ve hauled everything from lumber to mini excavators and I h have had zero issues with the brakes. Love em!
Bud M.
5/9/2024
@OtisH
Great to hear. Thank you for providing us with an update.
by: Micah11/26/2023
These are awful. The first set I installed kept on catching and sticking on, despite constantly adjusting them. The second set was lightly damaged in shipping (etrailer customer support is top notch and sent a replacement set out right away) but I installed them after the first set refused to work right. They're better but they're still the grabbiest trailer brakes I've ever towed and make it hard to get a decent setting on the brake controller for good braking that doesn't snap your head each time you step on the pedal but provides decent braking performance. Save your money and buy generic brakes, instead.
Jenny N.
11/28/2023
I wondered if you had also gone through the process of what we call bedding the brakes? This process allows the brake shoes and the magnet to seat to the drum. What you would do is drive the trailer out into an open area, like an empty parking lot. Get up to around 40 MPH and apply the manual override on your brake controller. Make sure the brake controller is set high enough where it will fully engage the trailer brakes [usually the middle setting will be just fine]. Do not hit the brake pedal during this time, as you want to slow down your vehicle and trailer with only the trailer brakes. You will most likely have to do this about 20 to 30 times to properly seat the brakes. When you feel like your brakes are properly seated, pull over and check for signs that you are done: a bit of smoke is normal and your brakes should be very hot [brakes should read 350-400 degrees with a temperature gun]. If you don't see these signs, then keep repeating the process until your brakes are properly seated.
by: Robert 05/01/2024
Direct replacement with all the parts needed, nice not to have to piece things together.
by: Jim 05/10/2024
Good product, good price, fast shipping! I will deal with e trailer in the future!
by: Jim 02/10/2024
I bought an 18 year old trailer with dexter axles so it made sense to rebuild the suspension with DEXTER components. Ordered,shipped,and rebuilt in a week. etrailer works for me!!!
by: Darryl R03/22/2024
"Top Shelf Service", by all!
Pleased with the complete price.
Well packaged.....arrived on the
projected date....in good condition.
Thanks, Darryl
Pleased " />
by: Patrick05/10/2023
Customer service was excellent, fast shipping and perfect replacement parts.
by: Tony07/08/2022
I purchased a brake assembly and hub kit for my travel trailer. I had a 100% positive experience with etrailer. Very helpful in placing my order.
All parts were correct and fit perfectly.
The only minor problems I encountered were as follows. The printed instructions included with the hubs were copies, that had been recopied about 3000 times. Practically illegible. One of the brake assemblies arrived without the small plastic clip that secures the wires for the brake magnet to the backing plate. Both of these small problems were "in the box" from Dexter and not the fault of etrailer
I will have no hesitation dealing with etrailer in the future.
Tony
7/11/2023
I am completely satisfied with my partspurchase 1 year later.
by: Calvin 11/29/2022
Great product, all hardware included, no problems
Calvin
12/4/2023
Works good. Bolted right up
by: Ron02/05/2024
Very easy installation. The order for the break assembly was delivered on time. Looks like quality parts.
Should add Dexter stickers to delivery so we can advertise for you
by: Jeffrey 03/15/2023
It was easy to find the correct part for my Aerolite, shipping was very quick
Jeffrey
3/16/2024
Perfwct replacement
by: George05/19/2024
Dexter always known for high quality items. Thier trailer brake assemblies were nice. Some minor paint scuffing on back side right out of their bags
by: Karen09/24/2023
We hadn’t changed anything on our 16ft trailer in 18 yrs. While the design had changed a bit all the new equipment fit like the original pieces.
by: Jan07/17/2023
The parts that I received were very well described. They installed perfectly with no problems.
by: James04/13/2021
Time to replace original brakes on Jayco travel trailer. Bought two fully assembled genuine Dexter trailer brake kits. One kit for each axle. Purchase price was excellent and received fully assembled as described. Packaging was great with no damage. Free shipping! The brake assemblies looked good with no issues. Definitely new! Installed with no issues. No missing hardware. Their website was easy to use. Will buy from them again. As a side note, really appreciate the videos they provide on their website to help as required.
by: Karen04/05/2024
It’s a good product.
by: Travis 05/08/2024
Fast shipping and great product. I will be ordering from them again
by: Karl 05/10/2024
Superb assemblies!
by: Nina 04/19/2024
The website was easy to find what we needed and the ordering process was so helpful
by: Matthew03/14/2024
Great equipment. Easy to install, good fit and easy to wire up!
by: Kenneth02/07/2020
Brake assemblies and drums arrived in perfect condition. Packed very well. It seems that way to many items from other online retailers come delivered damaged. UPS is hard on packages. etrailer.com also has superb customer service. Prices are very good. Thanks etrailer.co. Trailer lights were packed well to.
by: Matthew 01/17/2024
Excellent fit, excellent quality, shipped quick, arrived in perfect condition, I truly can't think of anything negative about the product or purchase experience. They are awesome to do business with!
25
395
Show More Reviews
See what our Experts say about this Dexter Trailer Brakes
- Replacement Brake Assemblies For a 2015 Forest River Flagstaff Classic Super Lite RV CamperTo determine exactly what brakes your 2015 Forest River Flagstaff Classic Super Lite camper came with I will need the serial number off your axles to verify what they got from the factory. You may have gotten the standard Dexter Electric Trailer Brake Kit # 23-26-27 or the Dexter Nev-R-Adjust Electric Trailer Brake Kit # 23-468-469. No matter which kit you originally got you can use the Dexter Nev-R-Adjust to eliminate the need to adjust your brakes. This will also ensure you have a better...
view full answer... - Parts Needed to Replace 12" Disc Brakes with Electric Drum BrakesHey Eric! Are you wanting to change from disc brakes to electric hub and drums, or are you just wanting to replace the rotors themselves? Traditionally 10" brakes are only compatible with up to 15" wheels but if yours have been working just fine then I can help you out with replacements. The 10" Dexter Electric Trailer Brakes # 23-26-27 will work if you have 3,500 lb axles and a square 4-bolt brake mounting flange (2-7/8" apart on center) but you'll also need 2 of the 10" Hub and Drum...
view full answer... - Replacement Brake Assemblies For A 2016 Keystone Sprinter Hi Ross, When replacing trailer brakes the best piece of information is going to be the axle capacity since this can narrow down the compatible options very quickly. From there we can measure the inside of the drum to determine the correct fit. 5.2K - 7k axles will usually have a 12" diameter x 2" wide brake assembly while 3,500lb and 4,400lb axles will typically have 10" diameter x 2-1/4" wide brake assemblies. You can look at the axle for a white sticker to see if you can find the...
view full answer... - Picking Out Replacement Brake Assemblies for 2003 Fleetwood Prowler LynxTo pick out the correct brake assemblies for your trailer you need to know a few things but I do not have ability to look up what your trailer would have had. You will want to measure the inner diameter of your hub/drums and the depth of the drums to determine what brake assembly dimensions you need. For example the part # 23-26-27 is a 10 inch by 2-1/4 inch thick brake assembly. You also want to determine what the bolt pattern is of your assembly mounting flange. The standard size is...
view full answer... - How To Determine Correct Brake Assembly For 2007 Airstream Safar Travel TrailerReplacement brakes typically correspond with the capacity of your axles. They also need to match the bolt pattern on the brake mounting flange as well as the size of your drum on the hub and drum assembly. Based on what I have found, it is likely that your 2007 Airstream Safari is using 3,500 lb axles. I recommend checking the axle tag to verify this information. If there is no information on the axle you could also measure the drum which would typically be 10" x 2-1/4". Although these...
view full answer... - What Hub/Drum Assembly Fits with the 10 Dexter Axle Brake AssembliesThe kit # 23-26-27 that you referenced only comes with left and right hand 10" brake assemblies. The drums are sold separately. The typical hub and drum assembly that fits with these brakes is the etrailer 3,500 lb # AKHD-545-35-EZ-K. Even though this is compatible with these brakes you need to verify that the 5 on 4-1/2" pattern is correct for your wheels and that your spindle uses an # L68149 inner bearing, # L44649 outer bearing, and a grease seal that has 1.719" and 2.565" inner and...
view full answer... - Replacement Hub/Drums and Brake Assemblies for 6x12 Enclosed Trailer with Axletek AxlesYou didn't mention the axle capacity of your trailer but if the drums you have now are 10 inch in diameter and the bolt pattern is 5 lug like you mentioned I'd be willing to bet they are 3,500 lbs hubs and the # AKHD-545-35-K would be what you'd need as a replacement and the brake assemblies part # 23-26-27 would also be a fit as well.
view full answer... - Parts Needed To Add Electric Drum Brakes To A Trailer To determine the correct brakes for your trailer we'll need to first know the axle capacity. The Dexter Electric Trailer Brake Kit # 23-26-27 you were looking at are designed for 3,500lb axles. From there you'll need a hub/drum assembly, which will require knowing your bearing and grease seal numbers and your wheel's bolt pattern. If you can't read the numbers on your bearings and grease seal then you can measure the spindle at points B, C, and D to get the inner diameter so that we can...
view full answer...
- Replacement 10 x 2-1/4 Inch Left and Right Hand Drum Electric Brake Assemblies I would be happy to help you. The 023-216-00 number you found is for a 10" x 2-1/4" left hand drum brake assembly. To replace it you will need the Left Hand: Dexter Electric Trailer Brake Assembly - 10" - 3,500 lbs item # 23-26 and Right Hand: Dexter Electric Trailer Brake Assembly - 10" - 3,500 lbs item # 23-27. The complete kit is the Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500 lbs item # 23-26-27.
view full answer... - Recommended Replacement Brake Assembly For 3500lb AxleThe Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange # 23-105-106-09 is designed to work with 6000lb axles with the AL-KO/Hayes 4 bolt flange, and will more than likely not work with your 3500lb axle since it more than likely uses the standard 4 bolt flange. The standard 4 bolt flange is has the holes 2-7/8" apart center to center, and the AL-KO/Hayes has a pretty odd pattern that you can see with the dimensions in the included diagram. You will want to measure the flange on your...
view full answer...
- How To Add Brakes to a Trailer with Lippert 3,500 AxleYes, the Dexter Electric Trailer Brake Kit part # 23-26-27 or part # 23-468-469 for self-adjusting will work great on a Lippert 3,500 lb axle. In addition to the brakes you'll also need hubs/drum for which I recommend the Dexter Trailer Hub & Drum Assembly part # 84546UC3-EZ. Finally, I do recommend using a junction box # 3375601101 and 7-Way Connector # H20046 to upgrade the wiring as well as a breakaway kit like the Hopkins Engager Push-To-Test Trailer Breakaway Kit part # 20400.
view full answer... - Is 4-Bolt Brake Flange Needed to Install 3,500 lb Hub & Drum AKHD-655-35-KGood question but no, the 4-bolt brake flange is not a requirement to install the Trailer Hub and Drum Assembly - 3,500-lb Axles # AKHD-655-35-K. The hub will still fit your spindle and install just fine, but you will need that 4-bolt brake flange if you were also installing brakes that fit the hub like the Dexter Hydraulic Trailer Brake Kit # 23-312-313 or Dexter Electric Trailer Brake Kit # 23-26-27.
view full answer...
- Hub & Drum With Electric Brakes Replacement For AL-KO 8700 HubThe Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 5-1/2 # AKHD-555-35-K will fit the spindle on your trailer to replace your AL-KO 8700 hub, but this does have a 5 on 5-1/2" bolt pattern. My information is the AL-KO 8700 has a 5 on 4-1/2" bolt pattern. BUT if you have or want to use wheels with a 5 on 5-1/2" bolt pattern you are fine with the hub you ordered; if you do have a 5 on 4-1/2" bolt pattern you will need the Trailer Hub and Drum Assembly - 3,500-lb Axles...
view full answer... - How Many Assemblies Come with Dexter Electric Trailer Brake Kit 23-26-27The Dexter Electric Trailer Brake Kit - 10inch - Left and Right Hand Assemblies - 3,500 lbs # 23-26-27 is a pair of brake assemblies. This includes a left and a right hand assembly so it basically comes with what is needed to replace the brakes on a single trailer axle.
view full answer... - Can Dexter Trailer Axle w/ Electric Brakes 7359765-EB Be Ordered With The 5 on 5" Bolt Pattern?I would be happy to piece together an axle with the components you need, but unfortunately the Dexter Trailer Axle w/ Electric Brakes # 7359765-EB you were looking at cannot be ordered with hubs that have the 5 on 5" bolt pattern you are needing. Instead you will need to go with the Dexter Trailer Axle Beam with E-Z Lube Spindles - 95" Long - 3,500 lbs # 7359765 which has the 95" hub face measurement and 80" spring center measurement you mentioned that you need, Dexter Electric Trailer...
view full answer... - Suspension Enhancement & Brake Controller Recommendations For 2006 Toyota 4Runner Towing TrailerWe can get you everything you need for your 2006 Toyota 4Runner, and let's go ahead and start with the suspension enhancement, for which there are two options, the SumoSprings # SS78DR and Timbrens # TTORSEQ. Between these two, the better option for your 4Runner is going to be the SumoSprings: - SumoSprings Solo Custom Helper Springs # SS78DR The reason for that is they have a 1,800 lb capacity - which is going to be more than enough to help reduce the squat for a more controlled towing...
view full answer... - Will Dexter Electric Trailer Brake Kit Fit 2002 Fleetwood Prowler With 10 Inch DrumsIt's a smart idea to go ahead and replace your brakes and yes, the Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500 lbs # 23-26-27 will absolutely fit your 2002 Fleetwood Prowler. The reason they will fit is these brake assemblies are the same dimensions as your drums, 10" diameter x 2-1/4" wide so they are perfect for you. These brakes fit a standard 4-bolt brake mounting flange which has bolt holes that measure 2-7/8" apart on center. The Dexter brake...
view full answer... - Replacement Parts For A Dexter 3,500 Lbs Axle Part # 35545E-ST-EZ-89According to the manufacturer, the Homestead Challenger Trailers are equipped from the factory with 3,500 lb axles with electric brakes. For these axles you will need the following: 2 Dexter Electric Trailer Brake Kit part # 23-26-27 (Manual-Adjust) Or 2 Electric Trailer Brake Kit part # AKEBRK-35-SA (Self-Adjusting) And 4 Bearing Kits for #84 Spindles part # BK2-100 I have attached a few articles for your consideration in addition to a review of the products I have recommended.
view full answer... - Determining The Correct Replacement Brake Assemblies For A 2016 Airstream Sport Travel Trailer There unfortunately isn't a guide to tell us exactly what your trailer has so we'll first need to check the axle capacity to determine the correct replacement brake assemblies. If you look at the axle tube there should be a sticker that lists the capacity of the axle. If your sticker is missing then you can also remove the hub and measure the diameter and depth of the assembly as pictured below. For example, the Dexter Electric Trailer Brakes # 23-26-27 you were looking at are rated for...
view full answer...
- How to Add 5 on 5-1/2 Lug Pattern Hubs to a M1102 Military TrainerI was able to find the maintenance manual online for your m1102 military trailer. The hubs use a outer bearing item # 14125A and inner bearing item # 25580. The only option other than an 8 on 6-1/2 hub is to use the Dexter Trailer Hub and Drum Assembly item # 8-174-5UC3 which has a 5 spoke pattern. This will not work with a 5 on 5-1/2 wheel. I recommend you replace your axle with the Timbren Trailer Suspension System item # ASR3500S06. This is an axle-les system with a 3,500 lbs capacity....
view full answer... - What Signs Should You Look For To Know When To Replace The Hubs On Your Trailer Typically if your hub is bad then you'll experience quite a bit of noise whether it's just when making turns or even while just rolling down the road if it's severe enough. The trailer will start to pull to one side when the brakes are applied, and you bearings will start to become loose. You could start to see visible damage to hub as well. A more noticeable sign is uneven tire wear or vibration and wobble, which can be caused by a loose bearing in the hub. It's so important to catch...
view full answer... - Replacement Trailer Brakes and Hubs for 2007 Jayco Jayfeather 25zThe brake assemblies you have are the same as part # 23-26-27 which is a standard 3,500 lb axle setup. This means that we know the correct brake hubs you'd need are # AKHD-545-35-EZ-K that you referenced. This comes with new bearings and seals as well.
view full answer... - Can Electric Brakes be Used on a Boat TrailerPeople use electric brakes on boat trailers all the time actually. We used to tell people they had to unplug their trailer wiring before backing the trailer into the water (still not a terrible idea) but in reality people leave the wiring plugged in all the time and rarely have issues. I sat and watched people on a boat ramp once (always entertaining by the way) and didn't see a single person unplug their trailer wiring before backing in and it didn't seem to phase any of the trailers....
view full answer... - Are The Dexter Electric Trailer Brakes # 23-26-27 WaterproofTraditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. The Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500lbs # 23-26-27 you referenced are not waterproof, so while I do not recommend them you can still use them on your boat trailer. I highly recommend using heat shrink butt connectors, like part # DW05745-10, when splicing...
view full answer...
Do you have a question about this Trailer Brake?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Expert Research:
Adam R
Edited by:
Lindsey S
Installed by:
Jeff D
Installed by:
David F
Video Edited:
Jacob T
Video by:
Dustin K
Updated by:
Wilson B
Written by:
Alexander C
Written by:
Ryan F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina D.
11/11/2023
I am sorry that the hubs arrived in this condition. Let me get you over to our customer service department for them to see what we can do for you.