Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4
(185 reviews)
Price: $8.97
In Stock
Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4
Item # BP10-220
Our Price: $8.97
Orders above $99 qualify for Free Shipping
In Stock
- All Info
- Reviews (185)
- Q & A (30)
- Videos (1)
- Photos
- Why etrailer?
Redline Accessories and Parts - BP10-220
- Trailer Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Adjuster Plug
- Redline
These replacement adjuster plugs fit many Dexter and Demco (Dico) electric and hydraulic trailer brake assemblies.
Features:
- These replacement adjuster plugs fit many Dexter and Demco (Dico) electric and hydraulic trailer brake assemblies
- Fits Dexter 7" x 1-1/4", 10" x 1-1/2", 10" x 2-1/4", and 12" x 2" electric and hydraulic brakes
- Fits Demco (Dico) 10" x 2-1/4" and 12" x 2" hydraulic brakes
- Quantity: 4 plugs
Specs:
- Overall dimensions: 1-3/32" long x 15/32" wide
- Plug bottom dimensions: 33/64" long x 21/64" wide
BP10-220 Adjuster Plugs for 7", 10", and 12" Brake Assemblies
Video of Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Redline Trailer Brakes BP10-220 Review
Speaker: Today, we're going to take a look at the adjuster plugs for the 7", the 10", and 12" brake assemblies. This part is for a quantity of four of them. These replacement adjuster plugs are designed to fit many Dexter and Demco electric and hydraulic trailer brake assemblies. They fit the Dexter 7", 10" and 12" Electric and Hydraulic Brake assemblies and the Demcos 10" and 12" hydraulic brakes. This part again is for a quantity of four plugs. The dimension on each plug, the over-all length is 1 3/32, the width is 15/32 wide. What these adjuster plugs are used for, they're used on a brake assembly.
Let me show you here. I happen to pull a 10" brake assembly. Let me zoom out here. At the bottom of all your brake assemblies on your trailer, there'll be an opening and there should be a plug in there. That plug is used for to seal off to keep any dirt and debris from getting inside your brake assembly when your drum's over this.
But, what you need to do is that slot 00:00:58 you pull that plug out. This plug is designed to go right in there. When you pull that plug out, it gives you access to adjusting your brakes, as you noticed the star wheel for adjusting your brakes is at the bottom. That slot is where you your screwdriver through and adjust that star wheel to adjust your brakes in or out. What you want to make sure you have is when you're done adjusting and put the plug back in again to keep any debris from getting in there. In this case, you happen to see there's just one opening so you just need one.
But on some there might be one slot or some there might be two at the bottom so you want to check your brakes and make sure you need to purchase how many you need to put in your brake assemblies. This part number I'm describing today is for a quantity of four. This is the adjuster plugs for the 7", the 10" and the 12" brake assemblies for a quantity of four.
Customer Reviews
Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4 - BP10-220
Average Customer Rating: 4.7 out of 5 stars (185 Customer Reviews)
These replacement adjuster plugs fit many Dexter and Demco (Dico) electric and hydraulic trailer brake assemblies.
- BP10-220
by: William10/07/2021
These fit perfectly into my Dexter electric brake assemblies
- BP10-220
by: Noel S.08/25/2015
As always, I am very impressed with etrailer.com. The prices are more than fair with shipping that can not be beat. I would recommend them anytime. I added the picture with the new Electric brake assemblies put on all 4 wheels. Also the brake adjuster plugs are added. Thank you Noel S.
- BP10-220
RobertOscar - 02/14/2019
by: RobertOscar02/14/2018
Ok, here is another product that is not nearly as good as it used to be. Remember when you were working on your 60's - 70's era cars.... huge drum brakes, adjusters and "little rubber plugs"? Well, now I know why all of them were missing on my TT, they are no longer nice quality, snug fitting rubber plugs like I used to swear at when trying to get time off. Nope, now they are some sort of harder rubbery plasticy sort of material with very little give and staying force.... They are not so easy to find, this seems to be as good as it gets so purchase extras!
Comments
Nothing to add, a year later and my opinion of these has not changed.
RobertOscar - 02/14/2019
- BP10-220
by: Dave W.07/06/2016
Bought a Keystone Hideout from a private party. While doing maintenance on the brakes found that there were no access plugs installed on any of the brakes. Did a web search for the AL-KO part number and etrailer was the only site that crossreffed the part number AND had them in stock. Parts came in the mail in 3 days from Missouri to PA. Part is not rubber but a semi-pliant plastic that fits very tight and needed a tap with a hammer to seat them. They pop out pretty easy with a screwdriver and can be re-installed with a tight fit. This is my second order from etrailer and they will be top of the list for future purchases.
- BP10-220
by: Ginger05/04/2021
We received the brake adjuster slot plugs however, they were loose in the shipping envelope instead of in 4 packs containing qty 4 plugs in each like our last order so we had to repackage them for retail.
- BP10-220
Tony T - 05/04/2016
by: Tony Testa05/05/2015
I received the order on time and in good order. I began to install the brake assembly, I discovered that the assembly was the wrong part. The "Backing Plate" has a different bolt pattern. However, I carefully checked all of the brake components and realized the parts would fit on the original backing plate. So I assembled and installed the assembly and it worked fine. The error was mine when ordering, a lesson learned. I really did not want to return the order if I didn't absolutely have to. So next time I will use OEM part numbers when ordering Dexter brake assemblies. This was a lesson learned and lots of research time to get it right. thanks!
Comments
Great no problems!
Tony T - 05/04/2016
- BP10-220
by: Steve W08/19/2014
got brake assembly's, drum, bearings, and adjuster plugs all excellent fit, price and received fast. Can't beat etrailer have bookmarked for future problems.
- BP10-220
by: Lawrence09/19/2021
Worked great!
- BP10-220
by: Frank09/24/2021
Parts worked perfect, so good I ordered more
- BP10-220
by: Bowie08/24/2020
They are perfect fit for my Dexter brakes. IMO they are way over priced for 4 little plastic pieces. Since the new trailers don't come with those adjuster caps now, have no choice but to pay for it.
- BP10-220
by: Daryl10/24/2018
Plugs arrived quickly and fit correctly. These plugs are a semi-rigid plastic, not rubbery, but seem to snap into place okay. All of my original plugs were missing, so I don't know if they were the same material or not. I am not 100% confident that these plugs are going to stay in place during travel, which is why I only gave 4 stars. etrailer service was quick and efficient, and I feel the price and shipping were fair. I will do business with them again in the future.
- BP10-220
by: Tony09/14/2017
Who ever heard of electric trailer brake assemblies not having these adjuster plugs. I had to order them extra after the brake assemblies were delivered.
- BP10-220
by: Anthony08/26/2021
Awesome!!!!
- BP10-220
by: Cherish08/20/2021
Exactly what I want it worked perfectly thank you
- BP10-220
by: DaveW07/21/2017
This is not so much a review on the inexpensive and simple product I bought, which was as expected, but more a review on etrailer.com in general. The site is pretty good for finding information, and that information seems quite good. etrailer impresses me as a reputable seller that I would go back to again if I need something they sell.
- BP10-220
by: Dave H.08/05/2017
Nice product that will work, but could not give it an excellent review because of the material it is made of. The plugs are more like a rigid plastic vs. a softer rubber material. One of them cracked as I pushed it into the slot, which makes me wonder how long they will last, especially when the temperature drops. I think if they were more pliable like the stock plugs, they will last longer. They are cheap enough and will work, just don't think they are going to last after a winter or two.
- BP10-220
by: George09/12/2018
I've ordered products from etrailer in the past. I've also discussed some of my purchases with their technical support team. Always helpful and knowledgeable. The orders so far, including this most recent one are correct, complete and delivered in a timely manner. etrailer is a good company to work with in my opinion.
- BP10-220
by: Timothy07/30/2021
Perfect fit for my needs!
- BP10-220
by: Martin07/23/2021
Very nice service...
- BP10-220
by: Luke Skalicky06/30/2019
I have two vehicles with drum brakes a 72 Dodge Charger (8 1/4) & a 00' (8 3/4) Ford ranger and this product went into place smooth as silk. The material was hard durable plastic and does what it's designed for and should be fine for daily driving. When it rains water gets into the drum through that oval hole & it's not good. Getter fixed today order NOW!!!
- BP10-220
Daniel L - 10/10/2017
by: Joseph Or10/09/2016
Your run of the mill backing plate adjuster hole rubber dust plugs. Soft, pliable and fit the holes just fine. Unfortunately there is not a lot to say about this particular product. I will be back the next time I need to purchase other trailer related products though.
Comments
After 18,000 miles over rough and dusty roads the plugs are still holding up just fine.
Daniel L - 10/10/2017
- BP10-220
Jack - 04/30/2019
by: Norman04/30/2018
Products were easy to install and appear to be of good quality. Can't tell if they will stay there and it is too early to tell if they are effective.
Comments
Has prevented moisture or dust from entering the brake drum. Exactly what it was designed to do.
Jack - 04/30/2019
- BP10-220
by: Craig H03/19/2018
How can you review something you haven't needed yet? I purchased these as a reverse-voodoo, just-in-case... if you have something, you're not gonna need it. Which is where I'm at with these adjuster plugs... they reside happily in my "spares" kit until one of the original plugs goes missing.
- BP10-220
by: Robert B02/22/2017
Generally speaking the product seems like a good buy. I looked at the different options at Etrailer and decided on the Dexter units even though they were slightly higher - made in USA. My package of parts arrived 3 days after ordering - a good deal considering the freight cost was $0. One of the brake assemblies had the self adjuster knocked halfway of in spite of the stiff spring hold it together to the shoes. I suspect this happened during shipment and due to bulk packing the 4 assemblies in a box. I would suggest that Etrailer warn their customers to look at their parts carefully upon receipt. I also was concerned about one of the 7/16" mounting studs being knocked out. I found the stud in the carton and reset it into the backing plate and did not have any issues in the installation. All in all the process went well from ordering to installation. I appreciated all of the helpful videos on line that helped with the ordering process and gave me a heads up on making sure to order nuts, washers and plugs for the adjusting ports. I would have given the review a 5 except for the packaging which could stand a little improvement.
- BP10-220
by: Jon E.04/30/2017
Haven't had much opportunity to test them in the Sierras but on the flat they work fine. The brake assemblies came as ordered and quickly. Installation was straight forward and went together with no problems.
26
186
Show More Reviews
Ask the Experts about this Redline Accessories and Parts
- Recommended Dust Cover Plugs For Dexter Brake AssembliesThe dust caps for the adjustment opening on your Dexter brake assemblies I recommend are the Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4 # BP10-220. These will work great with your assemblies.
view full answer... - Adjuster Plugs for 10 Inch Trailer BrakesThe adjuster plugs you're looking for are part # BP10-220. These fit the # AKEBRK-35 10 inch brakes you purchased.
view full answer... - What Are Dimensions of Redline Adjuster Plugs # BP10-220I walked out to our warehouse and pulled the Redline Adjuster Plugs # BP10-220, from our inventory. Checkout the short video I shot for you which shows the dimensions of the plug.
view full answer...![]()
- Replacement Drum Brake Adjuster PlugAL-KO part 568089 is an adjuster plug for a 12 x 2-inch drum brake. We offer a set of four of these as part # BP10-220. A single piece is also offered as part # 46-7. These fit 7-, 10- and 12-inch drum brakes from most brands.
view full answer... - Replacement Brake Assembly Plug Covers for Dexter Trailer Brake AssembliesYes we have the replacement brake assembly plugs with part # BP10-220.
view full answer... - Replacement Adjuster Plugs for Dexter Electric Brake AssembliesYes, to replace the adjuster plugs on Dexter Electric Brake Assemblies like the 10" # K23-463-00 that you were looking at you just need the part # BP10-220. These plugs can be used on all of the common electric brake sizes (7 inch, 10 inch, and 12 inch). This includes 4 adjuster plugs. I have attached a short video review that you can check out as well.
view full answer... - Will Dexter Brake Assemblies Fit on a Lippert AxleYou will have no problem using a Dexter brake assembly on a Lippert 7K axle. We have installed several Dexter brake assemblies on Lippert axles at our shop. Lippert and Dexter use the same standard mounting pattern and brake sizes. If you want standard brake assemblies, you could go with the Right Hand brake # 23-181 and the Left Hand brake # 23-180. I recommend stepping up to the Dexter Nev-R-Adjust brakes, # 23-465 and # 23-464. The cost difference is very minimal compared to the standard...
view full answer... - Adding Electric Drum Brakes to a Scamp Camper TrailerSetting up a trailer with electric drum brakes is going to be the easier and most cost effective way of adding brakes to your Scamp trailer. Since the trailer already has the mounting flanges that will limit the amount of parts and work that will need to be done. Starting with the hub and drum assemblies since your bearings are both L44649 and you have an EZ Lube style axle you would need # 8-257-5UC3-EZ with the 5 on 4-1/2 bolt pattern. They are designed for 2,000 pound axles but will...
view full answer... - Recommended Hub And Drum for Electric Brakes With 4 On 4 Bolt Pattern For 1973 Scamp TrailerThe hub we offer that will work with electric brakes and has a 4 on 4 bolt pattern, is part # 8-173-16UC3. You are correct that this hub and drum will only work with 7 inch x 1-1/4 inch brakes. The bearings, races, and seals are included with this assembly. I have attached a product review video for this hub/drum you can check out. The electric brakes that will work with this drum is designed for axles rated up to 2,000 lbs. The brakes have a 4 bolt mounting flange. For the right...
view full answer... - 10 Inch Hydraulic Trailer Brake Assemblies for etrailer 3.5K Hub and Drum # AKHD-545-35-KThe trailer hub and drum assembly # AKHD-545-35-K will take Bearing Buddy 1.98, # BB1980A or # BB1980A-SS (for stainless steel). For complete brake assemblies that fit this hub and drum I recommend the free-backing etrailer brakes # AKFBBRK-35L for the left side and # AKFBBRK-35R for the right side. If this is going on a boat trailer I recommend # AKFBBRK-35L-D for the left and # AKFBBRK-35R-D for the right. These brakes have a corrosion resistant dacromet coating ideal for marine applications. If...
view full answer... - Replacing Brake Assemblies and Drums on a 2000 Interstate Cargo TrailerSelf-adjusting brakes do work, but they will need to be adjusted when first installed. After the initial installation you will not need to do yearly adjustments. According to the Interstate Cargo Trailer Manual, you should have two 3500 lb axles, 15" wheels and your hubs should have a bolt pattern of 5 on 4-1/2". Based on that information, I recommend brake assembly kit # AKEBRK-35-SA and the hub and drum assembly # AKHD-545-35-EZ-K. Prior to ordering, please double-check that your...
view full answer... - Brake Assembly Dust Caps and Nut Recommendation for Brake Assemblies 23-105-106Sounds like you are looking for the dust cover plugs part # BP10-220 for the brake assemblies # 23-105-106. The bolts these are designed to fit to are actually studs that are attached to the mounting flange of your current spindle like the part # 4-44-1. For nuts and washers that fit that you'd want the part # 38LW and # 38N.
view full answer... - Brake Adjustment Tool Compatible With 12K Quality Axles Brake AssembliesThe Performance Tool Brake Adjustment Spoon for Drum Brakes # W80630 is a universal tool compatible with nearly all drum brake assemblies. This tool allows you to move the star shaped adjuster so you will have greater or less distance as your brake shoes require for proper use. You may also be interested in the Adjuster Plugs for 7", 10", and 12" Brake Assemblies - Qty 4 # BP10-220 to keep dirt and grime out of your brake assemblies to keep them functioning correctly in between adjustments.
view full answer... - Electric Brake Assemblies And Grease Seal Recommendation For Scamp TrailerThe Dexter 7 Inch Electric Trailer Brake Assembly, part # 23-47 is what you need for the left hand on your Scamp trailer. For the right hand you would need part # 23-48. These are designed with a 4-bolt mounting flange. These are used on the axle you said you have on your trailer, and will work well even though they say they have a 2,000 lb rating. The hardware kit you need for mounting each side is part # BIK-00. You will need a kit for each side. Adjusters plugs are available as well....
view full answer... - Replacement Parts for Dexter Nev-R-Adjust 12 x 2 Inch Electric Trailer BrakesThose are 12 x 2 Dexter brake assemblies, 5200 capacity, with 5 bolt mounting flange. But the Nev-R-Adjust brakes on these axles should be the 12 x 2 inch brakes. We have several parts available including the following: Actuating Arm, Left Hand, # BP02-230 Actuating Arm, Right Hand, # BP02-240 Shoe Hold Down Spring, # BP06-090 Shoe Return Spring, # BP07-105 (works on left or right hand sides) Adjuster Plugs, # BP10-220 Adjuster # BP10-060 (these are regular adjusters so you may...
view full answer... - Recommended Hubs Drums And Electric Brakes For 2000 Trails West 4 Horse TrailerFrom my research it looks like you have 6,000 lb axles on your trailer. You may want to check to see if there is a plate or sticker that shows the axle weight capacity. If you have a 5-bolt brake mounting flange I recommend the Dexter Nev-R-Adjust Electric Brake Assembly, part # 23-459 for the right hand and part # 23-458 for the left hand. These are designed to use with 12 inch hubs and drums. I have attached links to a product review video and an initial setup video for these brakes....
view full answer... - Do Dexter Nev-R-Adjust Brake Assemblies Include Adjuster PlugsThe Dexter Nev-R-Adjust Electric Brake Assemblies, like # 23-469, do not include plugs in the backing plates. To seal the adjuster holes, you will want to use the Adjuster Plugs for Brake Assemblies # BP10-220. These plugs are designed to fit Dexter and Demco 7 inch, 10 inch, and 12 inch electric and hydraulic brake assemblies.
view full answer... - Electric Brake Install 2000 Coleman SedonaLet's begin with the brake assemblies. You'll need the Dexter # 23-48 for the right side of the trailer, # 23-47 for the left. The brake assemblies have the mounting bolts integrated into the backing plate, but the necessary nuts and lock washers aren't included. We sell the nuts individually as part # 6-17 and the lock washer as part # 5-8. You'll need four of each per brake assembly. Dexter doesn't include the adjuster hole plugs with the assemblies, those are sold separately as part...
view full answer... - Do Dexter Brake Assemblies Like # 23-459 Include Adjuster Hole PlugsThe Dexter Axle # 23-459 12 inch Nev-R-Adjust brake assembly does not include the adjuster hole plugs which are sold in a quantity of 4 as part # BP10-220. The mounting hardware, # 38LW, # 38N nut and # 7-5 bolt are also sold separately. You'll need five bolts, nuts and washers per brake assembly.
view full answer... - Fit & Compatibility of Timbren Axle-Less Suspension w/4" Lift & Electric Brakes on 1962 AirstreamIt sounds like you might have a 1962 Globe Trotter Airstream Travel Trailer. According to my research this has a dry weight of 2,770lbs and a hitch weight of 400lbs hitch ball height of 19.5 If the 3,500lbs weight capacity will work for your loaded Airtstream, then the Timbren axle-less system # ASR3500S06 could be just what your looking for. Since this hasn't been installed on this trailer before here are the dimensions you will need to check to determine if this system will work...
view full answer...![Image 1 for]()
![Image 2 for]()
- Replacement Adjuster Plugs and Brake Line for Brake Actuator on Trailer with Surge BrakesAs long as the brake line you need uses 3/8 inch 24 UNF male and female fittings you can use # T0777300 if a 13 inch line is long enough. If not we have # T0776500 that 18-25/32 inches long which is more than enough. The adjuster plugs we carry are # 46-7 for one or # BP10-220 for a pack of four.
view full answer... - Hub and Drum Assemblies and Brakes for Timbren 2,200 Pound Axle-Less Suspension SystemTimbren axle-less suspension system # ASR1THDS02 can be used with hub and drum assembly # 84546UC3-EZ. For the right hand brake assembly use # 23-27 and for the left use # 23-26. For nuts and washers I recommend # BIK-00. And for adjuster plugs, # BP10-220.
view full answer... - Availability of Replacement Brake Shoes for Brake Assembly on Dexter 2.8K AxleFor your Dexter 2.8K axle, we do indeed offer replacement brake shoes. The part number is # BP04-065. We also offer replacement magnets, # BP01-068 for the oval magnet. We offer replacement actuating arms for the magnets, # 47-112-4 for the left hand or # 47-113-4 for the right hand. For a spring kit, use # K71-362-00, for the adjuster, part # BP10-060 and for the adjuster dust plug, part # BP10-220. We also offer the magnet retainer clips, sold in packs of four as part # BP19-001. Brake...
view full answer...![]()
- Initial Set-Up for 12" Nev-R-Adjust Electric Brake Assemblies # 23-458 and # 23-459I want to start by thanking you again for your purchase. We truly appreciate your business. When it comes to the 12" Nev-R-Adjust Electric Brake Assemblies, # 23-458 and # 23-459, the mounting bolts, nuts, washers, and adjuster plugs are sold separately. For adjuster plugs you will need part # BP10-220. As for replacing the adjuster wheel with one from your older assemblies, it most likely will not work. Last but not least, the performance of the brake assemblies. Poor performance...
view full answer... - Recommended Dust Cap Cover and Mounting Nuts for the Nev-R-Adjust Electric Brake Assembly # 23-468The Nev-R-Adjust Electric Brake Assembly # 23-468 does not include the mounting nuts or dust plug covers. You would need to purchase them separately. For the nuts you would want part # 6-17 and for the covers part # BP10-220. I attached a couple helpful videos to the right for you to check out as well.
view full answer... - Hardware for etrailer.com 10 Inch Trailer Brake AssembliesI'm not exactly sure what you mean by the seals for brake assemblies, part # AKEBRK-35-SA. If you mean the adjuster plugs then you want part # BP10-220. If you actually mean the grease seals that fit the 10 inch hubs the brakes are used on then it's almost definitely part # 58846 which has inner and outer diameters 1.719 and 2.565 inches respectively. You should verify the measurements to be sure. You can also verify the seal by checking the hub which would use the same bearings as...
view full answer...![Image 1 for]()
- Where to Manually Adjust the Brakes on a1991 GMC Cab & ChassisI spoke with one of our ASE-certified mechanics and he let me know that there is an adjustment access hole on the back of the brake drums on your 1991 GMC. There is usually a rubber adjuster plug in the hole that looks like # BP10-220. You will need to remove that plug to access the star-wheel adjuster. You can use a thin flathead screwdriver or a brake spoon like # W80630. I've included a link to our video on trailer brakes and installation. You can fast forward to the 4:35 mark to...
view full answer... - Replacement Electric Brake Assemblies for Denali Trailer with Tandem 5.2K Lippert AxlesI'm assuming that you're simply replacing the existing brake assemblies and that your trailer has hub/drums that have an inside diameter of 12 inches and a depth of 2 inches. I'm also assuming that your existing brake drums are in good shape, and you're planning on reusing them. If that's the case, I'd recommend the self adjusting electric brake assembly, part # AKEBRK-7R-SA for the right hand side, part # AKEBRK-7L-SA for the left. You'll need two of each. The brake assemblies don't...
view full answer...![]()
- Parts Needed to Add Electric Drum Brakes to a TrailerThe 10 inch brake assembly # AKEBRK-35R-SA (and matching left hand side # AKEBRK-35L-SA) is just the assembly itself. A complete assembly is the backing plate, shoes, magnet and the components used to secure them to the backing plate. The only thing that is needed is the nuts, washers, and adjustment hole plugs. The axle will have to have brake mounting flanges welded on to mount brakes. A brake mounting flange looks like # 4-35 or, on the end of an axle, it would look like # TRU74FR...
view full answer...
Do you have a question about this Accessories and Part?
Why etrailer.com?
At etrailer.com we guarantee:Highest quality accessories and parts for the best price.
Our Lowest Price Pledge ensures you will never overpay for the parts you need.Real product know-how.
We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem.Most detailed, accurate accessories and part information available.
Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.Installations, made easy.
We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions.Fast shipping.
Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Receive free shipping on orders over $99.Personalized service for life.
We provide one-on-one, personalized service from the ordering process through the life of your product.Trusted since 1946.
We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.Returns Policy
Need to return an item? No problem. Please read our Returns Policy for more information.
Info for this part was:
Video Edited:
Zack K
Installed by:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
Adam R
Updated by:
Wilson B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 800-298-1624
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.