See what our Experts say about this Optronics Trailer Lights

• Recommended Replacement Tail Light Assembly for 6 inch x 3 inch Tail Lights
  It sounds like you're looking for a set of submersible tail lights, and which ones you'll want to use depends on the other type of lights you currently have on your trailer-i.e. LED or incandescent. If you've got incandescent lights already on your trailer you can use something like the Optronics # ST56RS (passenger side) and # ST57RS (driver's side) and are 6" long by 3-1/2" tall. If you've got LED lights on your trailer the LED Combination Tail Light Kit for Trailers under 80" Wide...
  view full answer...
• Smallest Diameter Trailer Tire with At Least 1,800 Pounds Capacity and Parts for Building a Trailer
  Assuming the trailer is as single axle and only has two tires the smallest we carry is a 205/75-14 size tire. The Kenda # AM10235 measures 26.3 inches in diameter and has a weight capacity of 2,200 pounds at 75 psi. You also want to make sure the wheel has enough capacity. If you can tell me your bolt pattern I can recommend a wheel as well.
  view full answer...
• Upgrading Pop-Up Camper Taillights to LED
  Although they are a bit smaller than the lamps you are replacing, the Optronics # TTL56RK light kit would work great for you. The lamps would provide the same tail light, turn signal and brake light functions as the lamps you are replacing. The drivers side lamp will also provide illumination for the license plate. The only spot where you might have an issue would be in how the lamp attaches to the camper. The TLL56RK lamps are bolt mounted, with the head of the bolts fitting into slots...
  view full answer...
• LED Replacement Lights for Peterson M444
  We do have a couple of really good options for you to replace your Peterson # # PM444L and # PM444, but you do have a keen eye because the Tail Light Kit # TLL16RK will not work with the 2-1/4" spacing you have. One of the lights would interfere because it is too long overall and the back of the light cannot be rotated. Instead, for a couple of similar options that have 2" on center spacing and the needed space for you to mount them I recommend checking out the LED Combination Tail Light...
  view full answer...
• How to Determine Correct Tail Lights for Boat Trailer
  There is a way for you to pretty easily find out the tail lights you need, although the SAE numbers just means it has been approved by the Society of Engineers and aren't a part number, and we don't have any way of knowing specific lights for any trailer. So you will simply need to measure your current tail lights and find the one that most closely matches your measurement, and also know if your lights are surface mounted or recessed mounted. For example, the Optronics LED Combination...
  view full answer...
• What Does it Mean when a Trailer Light is Listed as Waterproof or Submersible
  When it comes to trailer taillights the terms waterproof and submersible are somewhat interchangeable. If a taillight is considered submersible that means that the internal circuits are waterproof and would be protected for if you were to back the trailer into water like when launching a boat. The part # TLL56RK that you referenced is listed as waterproof and submersible so it would work great on a boat trailer. Lights that aren't waterproof or submersible will still work just fine on...
  view full answer...
• What Mounting Bracket To Use With LED Combination Tail Light TLL56RK?
  Hello Richard, thanks for reaching out. Tail lights like the LED Combination Tail Light # TLL56RK generally mount to a bracket already present on the trailer, like in the picture below. We do not carry a bracket specifically for this light, but you could use eally any piece of metal with mounting holes 2" apart on center. We do carry one bracket from CE Smith, part # CE26057AA that has mounting holes 2" apart.
  view full answer...
• Recommended Disc Brakes, Actuator, and Lights for a 2005 Karavan Classic Boat Trailer
  Hey Anthony, thanks for all the information. To replace the hubs, I'll need to know the part numbers off of the bearings inside and your lug nut pattern. I do not have a database that shows me what part numbers are on trailers. To replace your disc brake actuator, I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout item # DX29FR, which bolts to the top of a 3" wide coupler or the Replacement Inner Member for Dexter DX7.5L Actuator item # DX99FR if you already have a Legacy...
  view full answer...
• Can Trailer Lighting with Three Wires Replace Two Wire Setup
  Trailer taillight kits like the part # TLL56RK that have 3 wires can install on trailers that have 2 wire setups pretty easily. What you would need to do is run the white wire of this kit to the mounting hardware and you'd be set. What you have now is designed to ground through the mounting hardware so with kits like this it would be just a matter of running the ground to the same place.
  view full answer...
• Side Marker Lights Required for Trailer Wider Than 80 Inches and Longer Than 30 Feet
  If your trailer is more than 80" wide and 37' long then you need 2 rear side marker lights, 2 rear side reflectors, 2 front side marker lights, 2 front side reflectors, 2 intermediate side marker lights and reflectors, as well as 2 front and 2 rear clearance lights. I have attached a helpful article that explains how many lights you need for different trailer variations and I clipped the parts specific for your trailer for you to check out. We have an abundance of lights and wiring as...
  view full answer...
  
• Replacement Taillights for EZ-Loader Trailer
  We carry all sorts of replacement trailer lights including taillights that you can see on the linked page. Since trailer makers do not maintain detailed specs on the lights they install during production you can match up the size, shape and functions of your taillights to those we offer, or you may be able to find a brand name and/or part number on the light base (not the lens). You can use the click on filters on the linked page to narrow the presented items to just those that match your...
  view full answer...
• Where Is Trailer Measured To Determine What Lights Are Required
  Actually, the width of a trailer is determined by it's widest point. If the wheels are outside of the frame of the trailer then the width is measured for that trailer from outside of the fender to outside of the fender on the other side of the trailer. If the wheels are under the trailer frame then the measurement is taken at the frame width only. I have attached a helpful article that explains how to measure a trailer and the article has also got a complete breakdown of the lights...
  view full answer...
• What are Lighting Requirements of Trailer that is Longer than 30 Feet
  I attached a link to a page that has all of the lighting requirements that your trailer would require but basically what you'll need are: 2 Stop/brake lights 2 Tail lights 2 Turn signals 2 Rear reflectors 1 License plate light 2 Rear side marker lights 2 Rear side reflectors 2 Front side marker lights 2 Front side marker reflectors 2 Rear clearance lights 2 Front clearance lights Rear identification lights
  view full answer...
• What do I Need to Completely Replace my Boat Trailer Lights
  I really like the LED Combination Tail Light Kit for Trailers part # TLL56RK. It offers LED lights which you won't have to be replacing bulbs in and with the submersible design you won't have to worry about water. It has the 4-way connector to connect to your Pathfinder and the wiring to make all of your connections. It also has the hardware for connecting the lights to the trailer. If for some reason your lights are different looking than these or you would like a different type please...
  view full answer...
• Recommendations For Complete Re-Wiring Of 6 X 12 Enclosed Trailer With LED Lights
  We do have everything you need to re-wire your 6 X 12 enclosed trailer. We also have any of the lights you said you want to use as well. For trailer wiring I recommend installing a 7-way so you can operate the light inside the trailer. The 7-way wiring I recommend is the Hopkins # H20046. This harness is an 8-ft long molded 7-way. I then recommend using a junction box like part # 38656. You would mount this on your trailer and then run your # H20046 wiring into the box. You can then...
  view full answer...
• Replacement Tail Lights for Boat Trailer Carrying 2018 Tracker Pro Team 175 TXW
  Rocks are definitely a menace to boat trailers but we can get you back out and fishing in no time on you 2018 Tracker Pro Team 175 TXW. Although we don't have specifics about the specific trailer you have, we absolutely have submersible LED trailer lights that will work for you. I highly recommend the LED Combination Tail Light Kit because both kits are bright, are extremely durable (the LEDs have a lifetime warranty), and have waterproof housing so they are submersible. To get the...
  view full answer...
  
• What is Needed to Convert Trailer Wiring to LED
  To convert a trailer to LED taillights is just a matter of swapping the fixtures with LED models or replacing the bulbs of the fixtures with the LED version. Unlike vehicles you don't have to swap in any special harnesses or resistors. Since you mentioned wanting a kit with wiring though we do have options like the # TLL56RK that include that as well as a pair of LED taillights. I also attached a link to a page that has all of the LED taillights we offer as well. If you see a light...
  view full answer...
• Easy to Install Wiring Harness on 2004 Jeep Liberty
  Since your 2004 Jeep Liberty does not seem to have the factory 7-way, the easiest to install 4-way that fits your Jeep is the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 42475. You'll only need to plug this into your Jeep's harness, and getting to that is likely going to be the most difficult part as you'll have to remove some interior paneling to find it. Then for lights, I recommend going with LED marker lights. Ten marker lights is quite a bit...
  view full answer...
• Required DOT Lights for a Pop-Up Camper
  For light requirements you have to look at the total length and width of the trailer along with its gross capacity. The 1987 Coleman Sequoia is 14 feet, 11 inches long and 6 feet, 8 inches wide. That makes the trailer right at 80 inches wide, but less than 30 feet long and the gross weight will be less than 10,000 pounds. If you go with the under 80 regulations, which is likely how Coleman manufactured this trailer because that is how it is set up then the trailer will need to have: Back 2...
  view full answer...
  
• Does LED Tail Light Kit TLL56RK Have Side Marker Lights
  The description of the LED Combination Tail Light Kit for Trailers under 80" Wide # TLL56RK does specify that the lights have a side marker function (in the second line under "Features"). I have added a link to a help article which details trailer lighting requirements, which are different not only for different trailer widths, but also lengths and weights. I have also added a link to a video installation I recommend taking a look at which details the side marker function of the LED...
  view full answer...
• Mounting Bolt Pattern of Optronics Trailer Light Kit TLL56RK
  The distance between the mounting holes of the Optronics trailer light kit part # TLL56RK is 2 inches like you mentioned needing. The distance from the mounting holes to the top of the light is 1.825 inches.
  view full answer...
  
• Replacement LED Tail Lights for 2017 Karavan LB-2200-70-17-SF-ST2-CR Boat Trailer
  For LED tail lights for your 2017 Karavan boat trailer I recommend the LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger # TLL56RK. These lights are virtually identical to the lights that came with the trailer so they will make a perfect replacement. They are 6-1/16" wide x 3-5/8" tall x 2-1/4" deep and come with a 25' wiring harness with a 4-way connection. These lights are waterproof and the built in license plate bracket is corrosion resistant....
  view full answer...
• Are Submersible Trailer Lights Guaranteed Against Leakage
  I have an explanation for you. Light kits like the LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible part # TLL56RK and other submersible trailer light are actually a little confusing. They are not completely sealed, if fact it is just the opposite there are drain holes on the light that will allow for the water to drain out of the lights after they have been submerged. On incandescent type submersibles there is a thin plastic shield around just the bulb to keep cold...
  view full answer...
• Replacement Tail Lights for Boat Trailer
  A 2015 Mako Pro Skiff 17 is a nice fishing boat but I assume you need taillights for the boat's trailer. While we do not have any specifics on a trailer for that boat, we definitely have taillights that will work. I highly recommend the LED Combination Tail Light Kit because they are bright, long-lasting with a lifetime warranty on the LEDs, and have waterproof housing to ensure they work perfectly with your boat trailer. To get the right kit you only need to know how wide the trailer...
  view full answer...
  

Do you have a question about this Trailer Light?