See what our Experts say about this Optronics Accessories and Parts

• Why is There a Driver and Passenger Round Optronics Trailer Tail/Stop/Turn Light
  The Trailer Tail Light # ST24RB is labeled as the passenger side because the driver side option, part # ST25RB, has a clear section on the underside of the housing to illuminate a license plate on a bracket like part # LP10SB. If you already have a light dedicated to the license plate then you can definitely use 2 of the passenger side options for your trailer. Attached are some review videos for you to check out. These light assemblies ground through the mounting hardware and then you...
  view full answer...
• Recommended Replacement License Plate Bracket, 4-Pin Harness, and Tail Lights for an 18' Bass Buggy
  Hey Ghent, I took a look at your trailer and it looks like they use square taillights, so something like the Optronics LED Combination Trailer Tail Lights # TLL160RK should work fine but I'd recommend measuring your current light first. These lights measure 8 1/16" long, 2 7/8" tall, are submersible, and has a 3 wire pigtail for easy install. This kit comes with both the left and right sides and has the stop, turn, tail, side marker, side reflex, rear clearance, and rear reflex functions...
  view full answer...
• License Plate Bracket Needed for Smaller Trailer License Plate
  From what you're describing it sounds like the Optronics Trailer License Plate Mount Bracket # LP10SB or the Cruiser License Plate Mounting Plate # CR79150 would be your best option since they have multiple mounting locations for the license plate. If you can send in the dimensions of your license plate (as well as the dimensions of the mounting holes) I can verify if these will work for your application or not.
  view full answer...
• Comparing Weight of EcoHitch, Curt, and Draw-Tite Trailer Hitches for 2019 Chevrolet Volt
  The EcoHitch # 306-X7338 weighs 37 lbs, Curt # C11436 weighs 26 lbs, and the Draw-Tite # 24947 weighs 21 lbs. The EcoHitch Invisi Trailer Hitch Receiver uses a flip-up license plate kit since the hitch installs behind your license plate. This does mean that you will not have a visible rear license plate with your bike rack installed. Typically your license plate would be obscured with the bike rack on the back regardless of the hitch. If you're worried about the legality of the plate not...
  view full answer...
• Recommended License Plate Relocation Bracket for a Cargo Carrier
  You're not supposed to block your plates and it will give them a reason to pull you over. Since you are going to be traveling through multiple states I recommend using the Trailer License Plate Mount Bracket item # LP10SB. This will allow you to relocate your license plate so it is visible behind the Curt Cargo Carrier item # C18110. If your tail lights will be blocked you can also use the etrailer License Plate and LED Tail Light Mounting Kit item # e98943-44LED.
  view full answer...
• Trailer Light Kits With Wishbone Wiring And Full Length Ground, Running Lights and Brake/Turn Wires
  The 25 Ft 4-Way Trailer Wiring Harness # A25W2GWB is our only wiring harness with a full length ground, running light and brake/turn signal wire to run down both sides of the trailer. While we do not have this in a kit you will simply need to select the additional lights you will need. For a trailer under 80" wide you will need the following parts. Driver's Side Tail Light # STL9RB qty 1 Passenger's Side Tail Light # STL8RB qty 1 Trailer License Plate Mount Bracket # LP10SB qty 1 Side...
  view full answer...
• Relocating License Plate and Bracket on a Utility Trailer
  I recommend using something like and L-bracket, such as # CE26098G, that you can attach to the top rail near the end of the trailer. Then you can attach a bracket such as # LPL55CB (may have to do some drilling/modify the L-bracket). Then you can ground the license plate bracket to the nearby frame of the trailer and the power wire to the running light circuit. The wiring can be run along the frame to the nearest tail light for the power wire. You can use wire ties or even metal loom claps...
  view full answer...
• License Plate Holder and Replacement Lights for Exiss Horse Trailer
  We have a few types of license plate holders to choose from and you can see all of them on the linked page. You might prefer one design over another for your Exiss horse trailer, such as the CE Smith Tread Plate design # CE26053A As for trailer lights we have products that are direct replacements for many popular OEM lights, and we also offer both basic incandescent bulb lights as well as brighter high-efficiency LED types that draw less power. We offer tail lights like Optronics' oval...
  view full answer...
• Are There Mounting Restrictions for the Trailer License Plate Mount Bracket
  The Trailer License Plate Mount Bracket part # LP10SB can be mounted where you choose so long as you are within the guidelines of local state ordinances . If you are unsure of your local state ordinances then you will need to reach out to the appropriate organization such as the DMV or DOT. We also have the Optronics LED Trailer License Plate Light w/ Bracket part # LPL55CB which has a light that is a requirement for most state ordinances.
  view full answer...
• License Plate Mounting Bracket for a Curt Cargo Carrier on a Volkswagen Beetle
  You can attach a license plate bracket to the back of the Curt cargo carrier # C18110 using # LP10SB. If you don't want to use one of the bolt locations on the carrier you could use self-tapping screws to attach it anywhere on the carrier.
  view full answer...
• Can A License Plate Be Mounted On the Swagman Bike Cover
  I do have an option for you but the Swagman Bike Cover for RVs part # S24FR does not have a spot for a license plate. If you want, you could most likely attach the license plate with some zip ties or you could mount the license plate elsewhere with the Optronics LED Trailer License Plate Light part # LPL56CB or the License Plate Mount part #LP10SB.
  view full answer...
• Recommendation for a License Plate Bracket for a Small Cargo Trailer
  I believe I have just the right license plate bracket for you. Take a look at the Trailer License Plate Mount Bracket, # LP15SB. It is just a little over 8 inches long at 8-7/16 inches. It is 4 inches tall. The center to center distance between the center slotted holes is 2-1/4 inches but can be 2-3/4 inches apart at the outside edges. The top most set of holes are 2 inches apart on center. I have included a picture showing the dimensions for you.
  view full answer...
  
• Dimensions and Hole Diameters on Optronics License Plate Brackets # LP5SB and # LP10SB
  I am including pictures of the Optronics Trailer License Plate Mount Bracket, part # LP5SB, and the Optronics Trailer License Plate Mount Bracket, part # LP10SB with the dimensions and hole diameters listed.
  view full answer...
  
• License Plate Bracket Needed for 23x47 Carpod Walled Cargo Carrier
  We do have license plate brackets like part # LP10SB that you could use to move your license plate so it sits behind the 23x47 Carpod Walled Cargo Carrier # M2205-2201. If you plan on driving at night time you should make sure to have a bracket with a light like part # PM436B. If you go this route then you will also need a wiring harness like part # HM38134 (you will connect the wire from the light to the brown wire and then cap off the additional wires for this application). Butt connectors...
  view full answer...
• Replacement Black Plastic License Plate Bracket to Replace Wesbar 3201
  We offer an exact replacement for Wesbar part 3201. The Optronics # LP10SB is a black plastic angled license plate bracket whose dimensions and mounting hole pattern are shown on the linked photo.
  view full answer...
  
• Recommended License Plate Brackets For Hitch Mounted Cargo Carrier
  We do have license plate brackets that can be mounted on a carrier. If you are looking for a bracket with an LED light I recommend part # LPL55CB. For a lighted bracket with a replaceable incandescent bulb I recommend part # LP55CB. To install either of these lights the black wire would need to tap into the running light circuit of your vehicle and the white wire would need to get grounded. The best way to wire this is to use a harness like part # HM48035. If you don't want to install...
  view full answer...
• Why Does Underside of Drivers Side Trailer Taillight Have Clear Plastic Lens
  Waterproof heat shrink butt connectors like # DW05744-5 would work great to tap your side-mounted clearance lights into the running lamp circuit which is typically carried by a brown wire, as you mentioned. The clear panel on the underside of the driver's side taillight is for illuminating a license plate if it's mounted below the taillight. If you don't have license plate mounting bracket, you can add one using part # LP10SB. Once the running lights are switched on, the license plate...
  view full answer...
• Submersible Tail Lights and 4-Way Wiring With Full Length Ground Wires For 15' Aluminum Boat Trailer
  You will need the following components as we do not have a kit with a full length ground wire harness. 4-Way Trailer Harness # A25W2GWB Driver Tail Light # STL37RB Passenger Tail Light # STL36RPG License Plate Bracket # LP10SB
  view full answer...
• Recommended Trailer Hitch for Carrying Bike Rack with Lights On 2022 Hyundai Tucson
  Hey Scott. For your 2022 Hyundai Tucson I recommend going with the etrailer # e38KR. This hitch has a nice matte black powder coat to blend in the black fascia on your car, and will install so only the receiver portion will be visible once it's on there. It's 525lb tongue weight is more than enough for a bike rack. Since you're going to need lights, you'll need wiring too of which I recommend # 118784. This'll give you the 4-way connector you need plug in your lights. If your bike rack...
  view full answer...
• License Plate Mount for a Trailer Hitch Receiver Mounted Bike Rack
  You will need to check with your local DMV to verify any laws, city or county ordinances that specify the visibility of your license plate behind the bike rack. We don't have any that are directly intended for this application, but some of the more popular ones are the Thule Replacement Licence Plate Bracket, part # 753-2023 and the Optronics License Plate Mount, part # LP10SB. If you plan on mounting and using either one of these, becuase they are not designed for this use, you'll have...
  view full answer...
• Do You Carry A Lighted License Plate Bracket For a Motorcycle License Plate On a Enclosed Trailer?
  While we do not have an exact part we do have all the parts that will allow you to mount your smaller license plate to your enclosed cargo trailer. First the Trailer License Plate Mount Bracket # LP10SB will give you an attachment point for the license plate and light. This is made of a rustproof black polymer that will last. A Peterson Great White LED Trailer License Plate Light # M290C-BT2 will attach to the top of the bracket to light up the license plate. You will need to provide...
  view full answer...
• Angled License Plate Bracket Recommendation for a License Plate Collection Display
  I think a better option for you would be the Trailer License Plate Mount Bracket # LP15SB. This bracket has an offset that is pretty close to 90 degrees and since it is a metal bracket it can be bent to the desired angle if needed. You could also paint the bracket with spray paint if you wanted.
  view full answer...
• License Plate Relocation Bracket for Viking Solutions Stack Rack II 2-Level Cargo Carrier
  It is good to note that when using a hitch mounted accessory like the Viking Solutions Stack Rack II 2-Level Cargo Carrier # 310-VSR201, that your license plate will be hidden when you have cargo loaded up. While Viking Solutions doesn't have a kit dedicated to relocating your license plate, we do have some options here at etrailer. I recommend either using the Mount Bracket # LP10SB or # LP5SB for your application. You will have to drill holes through the carrier, but after you do so...
  view full answer...
• Replacement License Plate Mounting Bracket that is Part of a Trailer Tail Light
  The mounting bracket or base is not available by itself so you would either need to replace the entire tail light or use a separate license plate mounting bracket such as # LP10SB. Since the light works just going with a separate bracket might be the way to go. The numbers on a tail light lens rarely help identify the light itself. If the model number of the light is not elsewhere on the housing you will need to go by the dimensions. Bargman Surface Mount Tail Light, # 30-92-003, that...
  view full answer...

Do you have a question about this Accessories and Part?