See what our Experts say about this Dexter Accessories and Parts

• Replacement Master Cylinder for Older Model Titan Model 60 Brake Actuator
  I spoke with my technical contact at Titan and showed him the photo that you sent in of your actuator. My contact confirmed that you actuator is a Model 60. The right replacement master cylinder for you will depend on what kind of brakes the actuator is designed for. If the brakes have never been changed out, you can determine this by checking if the trailer has disc or drum brakes. If your actuator is designed for drum brakes, you will want the Replacement Master Cylinder Assembly #...
  view full answer...
  
• My Surge Brakes Are Activating When I Back Up My Trailer - What Can I Do?
  Hello Gregg, I think I can help shed some light on what is going on. Basically, there are two ways to stop surge brakes from actuating when backing up the trailer. The first and most popular way to do this is to use a surge brake actuator with a reverse lockout. For example, the Dexter DX7.5L A-60 Brake Actuator # DX56FR has an electric lockout. The solenoid is wired to the reverse light circuit on the tow vehicle. This way when the vehicle is put in reverse, the actuator will be locked...
  view full answer...
• Troubleshooting Surge Brakes Not Releasing Pressure
  Hi Don; since the brakes aren't releasing it sounds like you have a bad master cylinder. Depending on the design it may also be the shock. It sounds like they are drum brakes so assuming it is the Dexter Model 60 the Replacement Master Cylinder Assembly # T4395100 you were looking at will work as a replacement. If you need a replacement shock it is the # T2336200.
  view full answer...
• How to Identify the Correct Replacement Shock for a Titan Surge Brake Actuator
  Thanks for sending the pictures Larry! I was able to identify your actuator from the original tag. You have a Dexter P-16 Model SLR surge brake actuator rated for 3,500 lbs. The Replacement Shock Absorber for Dexter Model 60 Brake Actuators # T2336200 you're looking at is the replacement shock for the older Dexter/Titan/Dico actuators and measures 4-15/16" collapsed and 6-1/4" extended, measured from the center of one mounting hole to the center of the other. Can you measure your existing...
  view full answer...
• Troubleshooting Disc Brakes Not Releasing
  If your disc brakes like the Kodiak Disc Brake Kit # K2R35S are not releasing it is likely an issue with the hydraulic actuator. Oftentimes this is the shock of the actuator having gone bad so it won't release all the way, so that would be the first thing to check; you could possibly replace it if that is the case. For example, if you had a Titan Model 60 Actuator you could use the Replacement Shock Absorber for Titan Model 60 Brake Actuators # T2336200.
  view full answer...
• Replacement Shock Absorber for Titan Trailer Brake Actuator Model 60
  For your Titan Model 60 Brake Actuator, I recommend the Replacement Shock Absorber for Titan Model 60 Brake Actuators # T2336200. This shock is a direct replacement and has and extended length of 6-1/4 inches and collapsed length of 4-15/16 inches.
  view full answer...
• Options For Replacement Shock on Actuator For Shoreland'r Trailer
  Hi Reid, You would need to know the brake actuator you have in order to get the correct replacement shock, as they are direct replacements for specific models of actuator, and I've gone ahead and listed out the options we have for you. - Replacement Shock for Titan Model 6 and 10 Brake Actuators # T1242600 - Replacement Shock Absorber for Titan Model 60 Brake Actuators # T2336200 - Replacement Shock Absorber Spring Kit for Titan/UFP Brake Actuators # TK71-758-00 - Replacement Shock...
  view full answer...
• Troubleshooting Brakes Locked Up on Surge Brake Coupler
  Hi Gene; I agree it is probably the master cylinder. I'm not 100% sure about the shock absorber since I don't see your order to know what actuator it actually is. However, I can't imagine you not seeing it is an issue if it worked for the last two years. If it is a Dexter Model 60 the correct master cylinder replacement is the # T4820000.
  view full answer...
• Rebuild Parts for a Modl 60 Actuator on a 1998 Haul Rite Boat Trailer
  Thanks for reaching out and providing the photos, Devin! You definitely have a Model 60 Actuator so you can use the following parts to get your system back up and running: - Master Cylinder Assembly for Drum Brakes # T4395100 - Shock Absorber # T2336200 - Push Rod Assembly # T2346300
  view full answer...
  
• Orientation of Replacement Shock Absorber for Dexter Model 60 Brake Actuators
  Hi Ed; the cylinder tube on the # T2336200 should be facing the front of the trailer and be the closest to the actual coupler. The piston rod will extend out toward the rear of the trailer.
  view full answer...
• Replacing the Shock Absorber on a Titan Model 60 Actuator
  The current shock absorber on your Titan Model 60 actuator won't be under any kind of pressure so it is simply a matter of taking the actuator apart to get at the absorber. The Replacement Shock Absorber for Titan Model 60 Brake Actuators # T2336200 may need to be slightly compressed when you fit it into the actuator but this is something that can be done by hand. It should be fully expanded when you receive it so you won't have to worry about expanding it for the installation.
  view full answer...
• Worn Out Actuator Shock Troubleshooting, Loud Clanking on Acceleration
  It sounds like the shock is worn out in your coupler and it is no longer functioning as a dampener to allow the coupler to return slowly and that is the clanking sound you are hearing. I attached a page that shows all of the different actuator shocks like # T2336200 that we offer. If you email me back with what model actuator you have I can help you pick one out.
  view full answer...
• Suggested Replacements for Titan Coupler and Brake Calipers
  As it looks like you have a Titan model 60 actuator, we definitely have replacements for you. If you wanted to replace the whole actuator, the Titan Zinc-Plated Brake Actuator w/ Electric Lockout - Disc - Multi-Fit Ball - Bolt On - 6,000 lbs # T4745720 will be a direct bolt on replacement. However, if you just wanted to replacement master cylinder and shock, you will need the # T4820000 and # T2336200. For the actual brakes, you have 2 options. If you wanted replace the whole caliper,...
  view full answer...
  
• Troubleshooting Titan Model 60 Brake Actuating Coupler Not Releasing Disc Brakes
  Since your brakes aren't releasing, it sounds like you either have a bad master cylinder in your surge coupler or a bad shock. The caliper piston moved when you released the pressure with the bleed valve, so it appears the plunger on the master cylinder is not responding when you release the brakes. This could be the master cylinder # T4820000 or it could be the shock # T2336200 has gone bad not allowing the pressure to be released.
  view full answer...
• Troubleshooting Surge Brakes Locking Up When Moving Forward
  Surge brakes use a hydraulic actuator to push fluid to the cylinder piston to activate the brake shoes on drum brakes or brake pads on disc brakes. This pressure should only be applied when weight is pushing against the hitch ball, so no pressure when moving forward and pulling the trailer. With brakes dragging and locking up when going forward, there has to be something mechanically incorrect in the system like a sticking piston in the wheel cylinder keeping pressure on the brake shoes...
  view full answer...
• Replacement Shock for Reliable Brand Actuator on a Mastercraft Boat Trailer
  One of our replacement shocks might work for your Reliable actuator but we do not carry that particular brand so you would have to go by the measurements. We have several models including # 1844-2. This particular model fits Toledo brand actuators. When fully closed it measures 6-1/4 inches from center of hole to center of hole and when expanded, it measures approximately 8-1/4 inches from center of hole to center of hole. Replacement Shock for Titan Model 6 and 10 Brake Actuators #...
  view full answer...
• Troubleshooting EZ Loadr Boat Trailer Brake Issues
  It sounds like the fact your brakes are locking and releasing is what will cause the bounce and porpoising you are describing. It sounds to me like your surge brake actuator is sticking and then releasing and then doing so again and again as you slow down. This could be from a shock like the Replacement Shock Absorber for Titan Model 60 Brake Actuators # T2336200 not working correctly, a wheel cylinder/brake caliper issue if that is only happening on one side, or a master cylinder issue...
  view full answer...
• Replacement Shock Absorber for M101A1 Military Trailer
  The Replacement Shock Absorber part # T2336200 is for Titan Model 60 Brake Actuators like the Titan Zinc-Plated, Leverlock Brake Actuator w/ Lockout Shield. If you have a Titan Model 60 Brake Actuator then the Replacement Shock Absorber will work for you but unfortunately, I don't have any information on what brake actuator is on your military trailer. If you would like to send me a few photos I can then forward them onto Titan to see if they recognize the brake actuator but if not then...
  view full answer...
• What Does Shock Absorber on Titan Model 60 Surge Brake Actuator Do?
  The Replacement Shock Absorber for Titan Model 60 Brake Actuators # T2336200 for your Titan Model 60 Surge Brake Actuator ensures smooth operation of the brakes when you apply the brakes of your tow vehicle by easing the trailer forward. Without a shock the actuator would apply the brakes very sporadically and cause a less than pleasant towing experience.
  view full answer...
• Replacement Shock for Worn Out One on a Titan Model 60 Trailer Coupler
  It does indeed sound like the shock is shot. The shock basically prevents the moving part of the coupler from banging around when stopping and accelerating. If you can easily move the coupler in and out by hand then it is for sure the shock. For the model 60 actuators use shock # T2336200. You mentioned adjusting the trailer brakes but make sure you have not adjusted them too far. There should be a slight but constant drag of the pads on the drum when the wheel is turned. You might also...
  view full answer...
• Troubleshooting Non-Electric Drum Brakes on an EZ Loader Trailer That Lock Up Moving Forward
  It sounds like you have surge brakes on your EZ Loader Duel axle trailer for your 1989 Bayliner. If your brakes are locking up when trying to move forward, it sounds like there is a mechanical error happening and it is most likely happening in the coupler. Something like a sticking piston in the wheel cylinder keeping pressure on the brake shoes or a plunger in the master cylinder that is not releasing. There is a shock like the # T2336200 in the coupler to help the coupler return to position...
  view full answer...
• Why Are My Calipers Dragging On My Load Rite Trailer?
  If your brake calipers are dragging, this is indicating that your caliper is not properly aligned with the rotor. This is caused by a bent caliper mounting bracket, or some warped rotors and pads. To fix this, you'll need to inspect the alignment between the rotor and the pad, and if it turns out to be a bent bracket simply replace as necessary. If you're able to send me the specific brake kit you have or some pictures of your brakes, I would be happy to see if we have some replacement...
  view full answer...
• Troubleshooting Hydraulic Trailer Brakes Initially Locking Up After Coming to a Stop
  It sounds like the shock absorber might be the issue here. The shock absorber, like part # T2336200 for Dexter Model 60 Brake Actuators, is designed to "push" the actuator back into a naturally opened position but it sounds like your coupler is staying compressed until your tow vehicle pulls it back open, which is why your trailer brakes are still activated until that initial "pull" you're feeling after a stop. Your trailer coupler should be very difficult to compress by hand (typically...
  view full answer...
• Are Surge Actuator Shocks Normally Hard to Push In and Pull Out
  Shocks like the Replacement Shock Absorber part # T2336200 that you referenced are normally pretty hard to push in and pull out so if that is what you are experiencing then yes it would seem like yours is working normally.
  view full answer...

Do you have a question about this Accessories and Part?