Lippert Ignition Proof 5th Wheel RV Landing Gear Switch w/Harness

Ask the Experts about this Lippert Accessories and Parts

How to Run Wiring fo...

How to Wire Replacem...

Landing Gear Moving ...

Landing Gear Moving ...

Landing Gear Moving ...

Replacing Ultra-Fab ...

Replacement Landing ...

Recommended Replacem...

• How to Run Wiring for Replacement Landing Gear Switch
  If you are using either the Lippert Components Landing Gear Switch # LC145236 or the Stromberg Carlson Landing Gear Switch # LG-145236 you will connect the red wire without the fuse along with the longer black wire to the red and black wires on your motor. The short black wire will be run to the battery's negative post and grounded and the pink or red wire with the fuse will be connected to the battery's positive post.
  view full answer...
  
• How to Wire Replacement Landing Gear Switch
  Do you know who the manufacturer of the landing gear is? That would be the only way to know for sure if a switch will work so the best option is going to be the Replacement Switch # LG-145236 which is designed for Stromberg Carlson landing gear but will work with most electric landing gear sets, such as Lippert, Venture and Atwood. Wiring this is pretty straightforward and I have included a diagram showing you how it is done (the switch also comes with written instructions). You only need...
  view full answer...
  
• How To Find the Correct Replacement Switch for a Landing Gear Set
  I have some great news, landing gear switches are fairly universal so we will have an option for you and for this I recommend the Replacement Switch for Electric Landing Gear part # LG-145236. If you have a dual motor setup and want to control each with a different switch then you can combine two otherwise you would just need one. In regards to installation, you might not just be able to match color for color but it will still be a sound replacement option. The wiring instructions will...
  view full answer...
• Replacement Switch For Landing Gear On 2021 Forest River XLR Boost?
  Yes! I confirmed with Lippert that the Lippert Ignition Proof 5th Wheel RV Landing Gear w/Harness # LC145236 will work as a replacement switch on your 2021 XLR12 Boost Toy Hauler.
  view full answer...
• How To Test A Landing Gear Switch Harness
  I contacted Lippert and their guidance for testing the Lippert Components Ignition Proof 5th Wheel RV Landing Gear Switch w/Harness # LC145236 is to use a voltmeter to verify power is getting to the motor. Test for power both before and after the switch. If you have power before the switch but not after, then the switch is bad. You will want to make sure the switch is on when testing. If you have power after the switch then the switch is good but if you don't have power before the...
  view full answer...
• Replacement Switch Availability for Powered Landing Gear for 2002 Thor Transport
  I'd need a little more info to be able to recommend for sure what the correct replacement switch is that you'd need, but we do carry replacement switches for powered landing gear sets. The Lippert landing gear replacement switch part # LC145236 is the most likely switch you need since it fits the most popular landing gear set out there. This also fits other popular brands like Stromberg Carlson and Venture.
  view full answer...
• Availability of Replacement Landing Gear Switch for 2007 Cedar Creek Silverback Trailer
  We do have a nice selection of replacement switches that may work on your Cedar Creek Silverback landing gear system. The Lippert Ignition Proof Landing Gear Switch # LC145236 that you were looking at is compatible with most systems produced today (as Lippert produces most of them), but if you can tell me what manufacturer/model landing gear set you currently have, I will be happy to confirm if it will work for you or make a different recommendation. Trailer manufacturers don't often...
  view full answer...
• Troubleshooting Replacement Lippert Jack Operating in Opposite Direction
  Although you wired up the new Lippert jack the same was as the failed unit, the fact that the jack is operating in the opposite direction from what you are pushing on the switch does indicate that the wiring leads are somehow reversed. Swapping the positions of the wires to the motor on your system should resolve this issue so that the stabilizer jack starts working correctly again. Please just let me know if you have any further issues and I wll be happy to do some more troubleshooting.
  view full answer...
• Troubleshooting Lipperty Hydraulic Leveling System Where Jack Won't Retract- Only Extends
  It's definitely possible that this has occurred during your re-build but it's more likely that whoever re-installed the unit got the plumbing for the hydraulic system mixed up. You'll want to make sure that the black hose is connected to the extend feed and the orange hose is connected to the retract feed-this is the opposite of what would be on a 5th wheel trailer with a similar hydraulic system, so that might be where the error lies. If both hoses are black then you would need to follow...
  view full answer...
• Replacement Landing Gear Switch Recommendation Rockwood Travel Trailer with Lippert Landing Gear
  Since you said your lading gear is electric and not hydraulic you would actually want the part # LC145236 and not the part # LC138415 that you referenced since it is for hydraulic landing gear sets.
  view full answer...
• Landing Gear Legs Keep Blowing Fuse Even After New Motor
  If you still continue to blow a fuse on your lading gear legs even with a new motor then that would lead me to believe you have an issue with the wiring or switch. Therefore, I recommend you trace the wires from the motor to the switch and then from the switch to the battery. If I had to guess I would say you have a short in one of these wires but I don't think the relay would be your issue. The Lippert Components Ignition Proof 5th Wheel RV Landing Gear Switch w/Harness part # LC145236...
  view full answer...
• Lippert Motorized Hydraulic Leveling System Controls Work The Wrong Jacks On a 2007 Daymon Daybreak
  It sounds like the wiring was changed going into the solenoids at the hydraulic pump on your 2007 Damon Daybreak. I would check these connectors as it sounds like they were mixed up if the unit was swapped out. This would explain why your jack positions are all off and why the auto level fails when you try to use it. The system sends power to one jack and when a different jack lifts the camper the internal sensors read an error.
  view full answer...
• How Many Terminals Are On the JR Products RV Landing Gear Switch
  The JR Products RV Landing Gear Switch part # 37213635 has four terminals; power, ground, motor in, and motor out. This will be the case for all of our landing gear switches. That said, most likely you have dual landing gear motors and just need to combine the motor in and motor out for each side before attaching to the switch. If you like, you could also just use two switches, one for each jack leg. The Lippert Components 5th Wheel RV Landing Gear Switch part # LC145236 comes with the...
  view full answer...
• Landing Gear Switch Installation on 5th Wheel Trailer
  For six poles on landing gear switch, I assume you are referring to a three switch assembly for passenger leg switch, dual switch, and driver leg switch. Unfortunately we don't have a schematic on your exact system, but typically on a 6 pole switch system, you have a power to the battery and a ground to the chassis. Then you have polarity for each motor. Positive polarity is normally red, and negative polarity is usually black or yellow depending on the manufacturer of the motor. We...
  view full answer...
• Looking for Less Bulky Switch Than Those Included with the Ultra-Fab Landing Gear Set # UF17-943010
  The Lippert Components Ignition Proof Switch # LC145236 will work with landing jacks that have a 12V motor so this would be one option for your client. Another option would be the Replacement Switch, # LG-145236. My contact at Stromberg Carlson said that this switch would work as well with the Ultra-Fab Deluxe Electric Landing Gear Set, # UF17-943010.
  view full answer...
• Landing Gear Moving In Opposite Directions When Switch Is Activated
  One of your motors is connected backwards and you'll need to simply swap the wires at the switch assembly # LC145236. Make sure to level your landing gear before you completely finish the assembly because the motors will work in sync with each other when you switch the wires around and you want your landing gear to move at the same rate. To level your trailer, simply unplug one motor and use the other to move up or down to match, then connect the wiring in the correct order to make both...
  view full answer...
  
• Will The Lippert Motor 142178 Work With the Landing Gear Set RVLG-8HDL
  Yes, the Lippert Motor for Electric Landing Gear part # LC142178 that you said you have will work with the Landing Gear Set part # RVLG-8HDL. The switch you have now can then be reused or we have the Lippert Components 5th Wheel RV Landing Gear Switch part # LC145236.
  view full answer...
• Replacement Motor for Venture Fifth Wheel Landing Gear
  The replacement motor for Venture fifth wheel landing gear is Lippert Components Venture 5th Wheel RV Landing Gear Motor # LC142178. The switch you'd want is Lippert Components 5th Wheel RV Landing Gear Switch # LC145236; the gearbox is Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies # LC276602. If you needed repair kits, we have those as well, the Lippert Components Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059 and the Follow...
  view full answer...
• Replacing Ultra-Fab Landing Gear With Lippert Landing Gear With High-Powered Motor
  Thanks for all that good info, and what you have is the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010, which you can replace with a Lippert set with a high speed motor on you RV, though you will need to have new brackets welded on. The issue is that the Ultra-Fab has an uncommon 20-1/4 inch space between the mounting brackets, while Lippert and most others have landing gear with the standard 17-1/2 inches. So if you were okay with having new brackets welded on to meet the spacing...
  view full answer...
  
• Recommended Replacement Landing Gear For 2004 Keystone Laredo 5th Wheel Camper
  I recommend going with an electric set for your 2004 Keystone Laredo 5th Wheel Camper. You could use # RVLG-8HDL, but I would add motor # LC142178 and a switch # LC145236.
  view full answer...
• Will the Ultra-Fab Deluxe Electric Landing Gear Set Fit a Keystone Montana 5th Wheel
  I do have an option but the landing gear hangers on the Keystone Montana are not standard and they will not match up with the Ultra-Fab Deluxe Electric Landing Gear Set part # UF17-943010. If you wanted to use the Ultra-Fab Deluxe Electric Landing Gear Set you would need to weld new hangers on. The other option we have for you would be to install a lead leg in place of the follow leg, the Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear part # LC178653 as this would then...
  view full answer...
• Diagnosing And Finding Parts For Landing Gear That Blows Fuse On 2009 Keystone Montana 5th Wheel
  Most Lippert landing gear systems just have one fuse so I don't think you will find another one in the system. The fact that you replaced the blown fuse and it still did not operate points to a few issues that could be going on. First, make sure the battery is properly charged and in good shape, then follow all the wires going from the battery to the switch, and from the switch to the battery making sure there are no pinched or bare wires. The best method for testing the circuit would be...
  view full answer...
• Replacement Landing Gear Recommendation for a 2011 Keystone Raptor 3812 Toy Hauler
  While I don't know exactly what landing gear you have on your 2011 Keystone Raptor 3812 Toy Hauler, I can say that you should be able to replace them with the Landing Gear Set w/ Handle # RVLG-8HDL as this landing gear uses the standard weld mount locations of 15-1/2" inside and 17-1/2" outside measurements (see attached). You can confirm fitment by measuring where the weld stops are on your current landing gear. This set comes with a handle but if you don't already have an electric motor...
  view full answer...
  
• Can a Single Motor Venture Landing Gear Set be Converted to a Dual Motor System
  To make the single motor landing gear into a dual-powered landing gear you will need to replace the existing follower leg with a lead leg # LC119102, add a new gear box LC276602, motor # LC142178, and switch # LC145236. It would be easier and cost less to just replace the whole system with a dual motor system such as # UF17-943010 rated for 12,000 pounds.
  view full answer...

Do you have a question about this Accessories and Part?