Convert-A-Ball Cushioned Weight Distribution Shank for 2" Hitches - 10,000 lbs

Ask the Experts about this Convert-A-Ball Accessories and Parts

Do you have a question about this Accessories and Part?

• Which Weight Distribution System is Best For a Ford F-150 Raptor and a 16 Foot Airstream Trailer
  
• From the weights you have listed it looks like you may at times have as much as 700 pounds of tongue weight with the weight loaded behind the rear axle in the truck. I recommend the Reese Strait-Line Weight Distribution System, 800 lbs. TW / 10,000 lbs. GTW, item # RP66073, as long as your tongue weight will not exceed 800 lbs at any time. Another option, if you need sway control, would be the Reese Strait-Line Hitch 800 lbs TW / 12,000 lbs GTW, item # RP66073. The Strait-Line sway control...
  view full answer...


• Weight Capacity of the Convert-A-Ball Adapter Part Number BA-1
  
• I contacted our representative at Convert-A-Ball and the weight capacity of the ball mount adapter # BA-1 is 10,000 pounds and tongue weight capacity is 2,000 pounds. It bolts right onto your weigh distribution shank such as the Convert-A-Ball # AMAC1. The adapter # BA-1 can fit other weight distribution shanks with 3/4 inch shank diameter holes and holes 1-1/4 inches apart on center. I added a short video review for you too.
  view full answer...


• Weight Distribution Setup with Sway Control for a 6,500 LB, 600 LB TW Trailer On 2009 Chevy 1500 4wd
  
• I would recommend the Reese Strait-Line Hitch 800 lbs TW / 12,000 lbs GTW, item # RP66073, this is the best system we have and actually works to keep sway from happening rather than stop it after it starts like other systems. The tongue weight that you mentioned falls right in the middle of the weight rating for this system so it is the perfect match for your trailer and would allow you to upgrade in the future if needed. Along with the weight distribution system you will need a weight...
  view full answer...


• Dimensions of Convert-A-Ball Cushioned Weight Distribution Shank # AMAC1
  
• I ran out to the warehouse, and pulled one of the # AMAC1 shanks. I found that the distance from the end of the shank that would insert into the hitch receiver to the center of the hitch pin hole is exactly 2-11/16 inches, as you can see in the accompanying photo.
  view full answer...


• Weight Distribution / Sway Control System That Will Fit A V-Nose Trailer
  
• Yes, the Strait-Line Weight Distribution Hitch System can be adapted to a V-Nose style trailer. You would need to use an alternate mounting system for the chain hanger brackets. The Bolt on Chain Hanger Kit, item # RP58305, will bolt onto the side of trailer frame. Once installed the chains are attached by raising the trailer tongue and rear of vehicle with the trailer jack. Tubular frames cannot be wider than 2-1/4 inches with this hanger kit, so you will need to be sure and measure before...
  view full answer...


• Maximum Drop When Convert-A-Ball Shank # AMAC1 and Ball Mount Adapter # BA-1 Are Combined
  
• I went out to our warehouse to take the measurement of those two parts together for you. The Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank # BA-1 when used with the Convert-A-Ball Cushioned Weight Distribution Shank # AMAC1 will give you a maximum drop of 7-5/8 inches. You may also wan the 3/4" Pins with Clips for Convert-A-Ball Weight Distribution Shank Accessories - Qty 2 # CABPN-2 for this combination.
  view full answer...


• Weight Distribution and Sway Control Recommendations for a 6,000 Pound Pace Trailer
  
• When choosing a weight distribution and sway control system, you will want to install one that has a tongue weight capacity range that encompasses your trailer tongue weight. Tongue weight should be between 10 and 15 percent of the gross trailer weight, or in your case, 600 to 900 pounds. With this is mind, I recommend a system with a range of 600 to 1,200 pounds like the Strait-Line Weight Distribution System with Sway Control, # RP66088. This system comes with built in dual-cam sway...
  view full answer...


• Hole Spacing For An Adjustable Ball Mount 2 Inches on Center
  
• I see the confusion with the hole spacing and think I can clear it up. The holes are 3/4 inch and they are 2-1/2 inches apart on center. They are not 1-1/4 inches apart however, that is the adjustment increment based on the Convert-A-Ball Cushioned Weight Distribution Shank for 2 inch Hitches,# AMAC1, this part is paired with. The actual metal spanning between the holes is 1-3/4 inches. The only similarly styled adjustable ball mount I could find that has a 2 inch on center adjustment...
  view full answer...


• Which Weight Distribution and Sway Control System Is Recommended for a Jeep Grand Cherokee
  
• The best sway control is provided by dual cam high performance sway control. I would suggest the Reese Strait-Line Hitch 600 lbs TW / 12,000 lbs GTW, item # RP66072 which will handle any load that will be within the weight capacity of your vehicle. This weight distribution and sway control system works to keep sway from starting rather than just stopping it once it begins, like other systems do. With this kit you will also need a Weight Distributing Shank, like item # AMAC1. You should...
  view full answer...


• What is the Tongue Weight Capacity of the Convert-A-Ball # BA-1 Ball Mount Adapter
  
• The tongue weight capacity of the Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank, item # BA-1, is 2,000 lbs. The gross trailer weight capacity of the Ball Mount Adapter is 5,000 lbs, and when used with the Convert-A-Ball Cushioned Weight Distribution Shank, item # AMAC1, you will need to stay within the weight capacity of the ball mount adapter which is 5,000 pounds.
  view full answer...


• Availability of 2-Inch Weight Distribution Shank with Tongue Weight Rating Higher Than 1600-lbs
  
• On the Reese weight distribution shank # RP54998 the distance from the center of the hitch pin hole to the head mounting holes is 9-1/4-inches. This is shown on the linked photo. This shank will work with your Reese trunnion head assembly. The grooves in the shank are provided to allow mounting of certain accessories. We do offer 2-inch weight distribution shanks with tongue weight (TW) ratings higher than 1600-lbs. For example, Convert-A-Ball Cushioned Weight Distribution Shank # AMAC1...
  view full answer...


• Recommended Weight Distribution Hitch for a 4,000 Pound Trailer and a 2003 Honda Pilot
  
• To be on the safe side, we will assume the maximums; trailer weight of 4,000 pounds and tongue weight of 425 pounds. When selecting a weight distribution system, the most important thing is properly matching tongue weights. That being said, you never want to exceed the gross trailer weight capacity either. We have a few weight distribution systems with sway control, that have a 400-600 pound tongue weight range and they all have more than enough gross trailer weight capacity. Being that...
  view full answer...


• Measurements from Hitch Pin Hole to Gussets on Cushioned Weight Distribution Shank Part # AMAC1
  
• The distance from the center of the hitch pin hole to the rear of the bottom reinforcing gusset is 3-3/4 inches. The distance from the hitch pin hole and the top gusset is right at 4 inches. I have edited a photo showing how the measurements relate to the # AMAC1 shank.
  view full answer...


• Need a Shorter Weight Distributing Hitch Shank
  
• We do have a few options for replacement WD shanks that have a distance shorter than 8 inches from the center of the hitch pin hole to the center of the adjustment holes. The Convert-A-Ball Cushioned Weight Distribution Shank # AMAC1 fits 2 inch hitch receivers, measures 6-3/4 inches from center of hitch pin hole to the center of the adjustment holes, and has a Gross Trailer Weight (GTW) capacity of 10,000 lbs with a Tongue Weight (TW) capacity of 2,000 lbs. The distance between the...
  view full answer...


• Can I Use # 66010 Trunnion Bars in My # RP66131 Weight Distribution System to Increase Weight Cap.
  
• I spoke with my contact at Reese and he informed me that yes, you can swap the Reese Replacement Trunnion Spring Bar, 1,700 lbs, part # 66010 into your Reese Weight Distribution w/out Shank - Trunnion Bar - 15,000 lbs GTW, 1,500 lbs TW, part # RP66131, to increase the capacity of your weight distribution system to 1,700 lbs. The head of your weight distribution system is capable of the 1,700 lbs, however you will need to make sure the the shank you are using is capable of 1,700 lbs tongue...
  view full answer...


• Recommended Weight Distribution Shank Compatible with Blue Ox Sway Pro System
  
• Yes, the Convert-A-Ball Cushioned Weight Distribution Shank for 2" Hitches - 10,000 lbs # AMAC1 will work with the 2,000 lb tongue weight of the Blue Ox SwayPro # BXW2000 but it will limit the towing capacity to 10,000 lbs. Your only other option is to replace your trailer hitch receiver. If you go this route, I recommend the Draw-Tite Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" # DT45508 which is a custom fit for your 1999 Ford Super Duty Truck
  view full answer...


• Can Convert-A-Ball Cushioned Weight Distribution Shank be Used Without a Weight Distribution System
  
• Yes, you can use the Convert-A-Ball Cushioned Weight Distribution Shank # AMAC1 without a weight distribution system and it will keep its 10,000 pound weight rating. The Ball Mount Adapter # BA-1 is designed to work with it just for that purpose and is also rated for 10,000 pounds GTW.
  view full answer...


• Weight Distribution System And Towing Mirror Recommendations For 2009 Chevrolet Suburban
  
• Thank you for the great information about your 2009 Chevrolet Suburban and your new trailer. It really helps when we try to find components that work best for you. You will want to choose a system where the tongue weight falls near the middle of the weight distribution system range. The tongue weight will be the tongue weight of the fully-loaded ready-to-tow trailer added to the weight of any cargo placed behind the rear axle of your towing vehicle. A system like the Pro Series Weight...
  view full answer...


• Recommendation for WD/Sway Control for 2007 Fleetwood Saratoga and 2010 Ford Flex
  
• Tongue weight will depend on how you load it. I would check the Flex owners manual to see what the weight distribution capacity of the vehicle is. Some vehicles cannot use weight distribution systems. I am not sure on the Flex, but to be safe, I would strongly recommend checking the owners manual. Some of the aftermarket hitches we have do allow use of weight distribution system and some do not. The ones that do, do not allow an increase in tow capacity. So I would imagine if your factory...
  view full answer...


• Drop Dimensions of 11 Inch Weight Distribution Shank # RP3215
  
• The minimum drop is 4-1/2 inches, the maximum is 6-7/8 inches and it adjusts by 1-1/4 inch increments. Since you need a drop of 3-1/2 inches, # RP3215 is not the best option for your application. Part # AMAC1 has a maximum drop of 3-3/8 inches which is close enough to 3-1/2 inches. It has a maximum tongue weight capacity of 2,000 pounds and maximum trailer weight of 10,000 pounds. If you have a heavier trailer weight, you can use part # RP54977. It has a minimum drop of 3-1/4 inches...
  view full answer...


• Can Convert a Ball Shank AMAC1 and Platform BA-1 Achieve 2 inches of Rise
  
• The ball mount adapter part # BA-1 that you referenced will fit the Convert a Ball shank part # AMAC1. With the shank in the rise position you could easily achieve 2 inches of rise.
  view full answer...


• How to Figure out Which Replacement Arms are Needed for Weight Distribution Hitch
  
• The biggest difference is going to be that the Reese replacement bars are going to have a tapered end, like you can see in the photo of Replacement Round Spring Bar for Reese Weight Distribution System - 800 lbs TW # RP58114. The other photo - with the chain - is the Replacement Spring Bar for Curt Round Bar Weight Distribution System - 600-800 lbs TW # C17113. I've added links to our pages with our replacement round bar selections from both Curt and Reese for you to take a look at. As...
  view full answer...


• Weight Distribution Recommendation for Towing a 24 Foot Travel Trailer with a 2005 Isuzu Ascender
  
• You are correct, the 24 foot Coachman travel trailer you are considering will require weight distribution for use with your vehicle, and for safety sway control is a good idea. The dual cam sway control you have referenced is the best sway control available, and keeps sway from starting rather than reacting to it like some other systems. You will need to check your trailer weight fully loaded and ready to tow, to be sure you are within the capacity of the hitch and vehicle. Your vehicle...
  view full answer...


• Recommended Weight Distribution With Sway Control For 2012 Chevy Traverse
  
• You will need to know what the tongue weight is to make sure you get the right weight distribution system. Tongue weight is the tongue weight of your fully-loaded-ready-to-tow trailer added to the weight of any cargo you have loaded behind the rear axle of your towing vehicle. For your 2012 Chevrolet Traverse I recommend the Strait-Line Weight Distribution w Sway Control, part # RP66072. This weight distribution system features can handle tongue weight between 200 and 600 lbs and has...
  view full answer...


• Will Ball Mount Adapter Work With Weight Distribution Shank
  
• I pulled one of the Ball Mount Adapters, part # BA-1 from our warehouse and took a measurement for you. As the attached photo shows, the center-to-center measurement is 2-1/2 inches. With 3 inch spacing on your shank this will unfortunately not work for you. We do offer a shank that might work for you and will work with the ball mount adapter. I recommend the Convert-A-Ball Cushioned Weight Distribution Shank, part # AMAC-1. This Shank fits 2 inch receiver openings and the holes are...
  view full answer...


• Compatibility of Ball Mount Adapter # BA-1 with Weigh Safe Hitch Ball with Scale # WSUN-1
  
• I went out to our warehouse to measure the Ball Mount Adapter for Convert-A-Ball Cushioned Weight Distribution Shank # BA-1 for you. The platform measured 11/16th inches which is the 3/4 inch platform they are referring to. I recommend the # BA-1 for your Weigh Safe 2" and 2-5/16" Hitch Ball w/Built-In Scale # WSUN-1. These two parts will work very well together. That platform is designed to work with the Convert-A-Ball Cushioned Weight Distribution Shank for 2" Hitches # AMAC1,...
  view full answer...


• Will Convert-A-Ball Weight Distribution Shank # AMAC1 Fit a Husky Weight Distribution System
  
• Husky is the one brand that I know of that has at least 2 different shanks with different sizes as far as the hole diameter goes. You have to measure your existing shank to determine if # AMAC1 will fit. The vertical part of the # AMAC1 is 2 inches square. The holes are 1-1/4 inches apart on center. And the holes are 3/4 inches in diameter.
  view full answer...


• Can Convert-A-Ball Ball Mount Adapter Be Used with Any Weight Distribution Shank
  
• The Ball Mount Adapter # BA-1 can be used with any weight distribution shanks with 3/4 inch shank diameter and holes 1-1/4 inch apart. Which is the standard. The only shank type you will not be able to use it with are shanks with a hollow channel, such as part # RP63971. The holes will not line up with the holes on the adapter. But if you stick with a solid design like the # AMAC1 you'll be just fine.
  view full answer...


• Can Convert-A-Ball Dual-Cushioned Adjustable Ball Mount Be Used with Weight Distribution System
  
• I do have a great solution for you, however the Convert-A-Ball Dual-Cushioned Adjustable Ball Mount # CAB-UM that you referenced cannot be used with a weight distribution system, in large part because of its adjustment hole spacing. Just about any weight distribution shank features adjustment holes that are spaced 1-1/4 inches apart, on center. The shank for the Convert-A-Ball features adjustment holes are are spaced apart by 1-1/2 inches. This simply means that the holes will not line...
  view full answer...

Do you have a question about this Accessories and Part?